-
Jet JJ-8CS - page 1
OWNER’S MANUAL JJ-8CS W oodworking Jointer JET EQUIPMENT & TOOLS, INC. P .O. BOX 1349 Phone:253-351-6000 A WMH Company Auburn, W A 98071-1349 Fax: 1-800-274-6840 www .jettools.com e-mail jet@jettools.com M-708458 06/01 ...
-
Jet JJ-8CS - page 2
2 W arranty & Service The JET Group warrant s every product it sells. If one of our tools needs service or repair , one of our Authorized Repair S tations located throughout the United S tates can give you quick service. In most cases, any one of these JET Group Rep air S tations can authorize warranty repair , assist you in obtaining p arts, o ...
-
Jet JJ-8CS - page 3
3 W ARNING Wear eye protection. Always keep cutterhead and drive guards in place and in proper operating condition. Do not remove guard for rabbeting operations. Never make a jointing, planing, or rabbeting cut deeper than 1/8” . Always use hold-down/push blocks for jointing material narrower than 3”, or planing material thinner than 3? ...
-
Jet JJ-8CS - page 4
4 • Don’t overreach. Keep proper footing and balance at all times. • Maintain tools with care. Keep tools sharp and clean for best and safest performance. Follow instruc- tions for lubricating and changing accessories. • Always disconnect the machine from the power source before servicing. • Reduce the risk of unintentional starting. Make ...
-
Jet JJ-8CS - page 5
5 T able of Contents W arranty ......................................................................................................................................................... 2 W arnings ....................................................................................................................... ............................. 3-4 ...
-
Jet JJ-8CS - page 6
6 Levers and Controls 1. Handwheel for Outfeed T able 8. On/Off Switch 2. Outfeed T able 9. Rabbeting Ledge 3. Fence 10. T able Lock Knob 4. Fence Adjustment Handle 1 1. Fence T ilt Lock Handle 5. Cutter Guard 12. Fence Control Handle 6. Infeed T able 13. Belt Guard 7. Handwheel for Infeed T able 14. Dust Chute Specifications: JJ-8CS S tock Number ...
-
Jet JJ-8CS - page 7
7 Contents of Shipping Cartons Note: unit shipped in two cartons. Stand Carton 1. S tand with Motor 1. S tand Door 1. Dust Chute w/ Mounting Hardware Main Unit Carton 1. Bed Assembly w/ Fence 1. Cutter Guard 3. Mounting Bolts 3. 3/8" Lock Washers 1. Belt Guard 3. Hex Wrenches (3, 4 & 5mm) 2. Handwheels 2. Handles 2. V -Belts 1. Can of T ou ...
-
Jet JJ-8CS - page 8
8 Installing Bed to Stand 1. Use an assistant or hoist mechanism to place bed assembly on top of stand. Be sure identi- fication label on the bed faces the same direc- tion as the label on the stand (Fig. 1). 2. Line up two holes in top of stand with holes in bed assembly by viewing through access door in stand. 3. Attach bed assembly to stand with ...
-
Jet JJ-8CS - page 9
9 Assembling Knife-Setting Gauge 1. Place the two bases (A, Fig. 4) onto each end of the bar (B, Fig. 4). Snap the four E-rings (C, Fig. 4) into the grooves on the bar as shown. 90 ° Fence Adjustment Note : whenever making an adjustment to the fence, lift the fence up slightly after releasing the lock handle to avoid scratching the table. 1. Set i ...
-
Jet JJ-8CS - page 10
10 45 ° Fence Adjustment Note : Whenever making an adjustment to the fence, lift the fence up slightly after releasing the lock handle to avoid scratching the table. 1. Loosen lock handle (A, Fig. 7). Move the stop plate (B, Fig. 7) out of the way and position the fence at the 45 ° angle. Make sure the fence sits against the stop bolt (C, Fig. 7) ...
-
Jet JJ-8CS - page 11
11 5. When the outfeed table and blade number one are the same height, tighten table lock screw . 6. The knives must be parallel with the outfeed table. Bring the straight edge forward to the front of the outfeed table and confirm that blade number one is at the same height at the front of the table as it is at the back of the table. 7. If blade is ...
-
Jet JJ-8CS - page 12
12 Installing V -Belts 1. Disconnect the machine from the power source, unplug. 2. Remove the lock knob (A, Fig. 14) and belt guard (B, Fig. 14). 3. Place v-belts onto cutterhead pulley grooves and through opening in stand. 4. Pull v-belts down and place onto motor pulley (Fig. 15). If necessary , loosen the mounting screws (A, Fig. 15) and slightl ...
-
Jet JJ-8CS - page 13
13 Installing Access Cover 1. Install access cover by placing bottom of panel into access in stand and fastening by turning latch (Fig. 17). If the access door latch needs adjustment: 1. Remove the access door from the stand. 2. Loosen the hex lock nut (A, Fig. 17). Rotate the latch a quarter turn clockwise to tighten and counterclockwise to loosen ...
-
Jet JJ-8CS - page 14
14 Operation W ARNING Keep all guards in place and in adjustment at all times during the cutting procedure! Keep hands away from the cutterhead! Do not pass hands directly over the cutterhead! The use of push sticks and/or handle pads are highly recommended when using the jointer! Failure to comply may cause serious injury! Jointing cuts or edg ...
-
Jet JJ-8CS - page 15
15 Jointing W arped Material If the work to be jointed is cupped or warped, take light, repetitive cuts until the surface is flat. Forc- ing the material flat against the table will still leave a warped piece after the cuts have been made. W ARNING Never joint any material shorter than eight inches! The material may tip into the jointer’s thr ...
-
Jet JJ-8CS - page 16
16 Rabbet Cut W ARNING Rabbeting requires the removal of the cutterhead guard. Use extreme caution when making rabbeting cuts and replace the guard immediately after completion! Failure to comply may cause serious injury! 1. Adjust the fence so that the distance between the end of the knives and fence is equal to the width of the rabbet (Fig. 2 ...
-
Jet JJ-8CS - page 17
17 6. Insert lock bar and screws and tighten to hold in place. Blades are set at the proper height when the top of the blade is 1/16" above the cutterhead. 7. Repeat for other two blades. 8. T o set the knives to the outfeed t able and to the same height in the cutterhead, see section titled “Leveling Outfeed T able to Cutterhead Knives” f ...
-
Jet JJ-8CS - page 18
18 Sharpening the Knives W ARNING Blades are extremely sharp! Use caution when handling. Failure to comply may cause serious injury! 1. Disconnect the machine from the power source. 2. Remove the fence, blade guard and belt cover . 3. T o protect the infeed t able from scratches, par- tially cover the sharpening stone with paper . (Fig. 30) 4. ...
-
Jet JJ-8CS - page 19
19 T rouble-shooting e l b u o r Te s u a C e l b i s s o Pn o i t u l o S e h t n o d e v a c n o c s i k c o t s d e h s i n i F . d n e d e e f t u o e h t n a h t r e h g i h s i p i t e f i n K . e l b a t l e v e l s i t i o s e l b a t d e e f t u o e s i a R . p i t e f i n k h t i w s i k c o t s d e h s i n i f f o e d i s k c a B . e d i ...
-
Jet JJ-8CS - page 20
20 Fence Assembly ...
-
Jet JJ-8CS - page 21
21 Parts List for the JJ-8CS W oodworking Jointer Fence Assembly Index Part No. No. Description Size Qty . 1 ......... JC-F01 .............................. Fence Body ....................................................................... .................. 1 2 ......... JC-F02 .............................. Fence Link ............................ ...
-
Jet JJ-8CS - page 22
22 Bed Assembly ...
-
Jet JJ-8CS - page 23
23 Bed Assembly Index Part No. No. Description Size Qty . 1 ......... JC-T01 .............................. Base ............................................................................. .......................... 1 2 ......... JC-T02 .............................. Front T able ................................................................... ...
-
Jet JJ-8CS - page 24
24 Stand and Motor Assembly ...
-
Jet JJ-8CS - page 25
25 Stand and Motor Assembly Index Part No. No. Description Size Qty . 1 ......... JC-M01W .......................... S t and ....................................................................................................... 1 2 ......... JC-M02W .......................... Motor Mount ............................................................ ...
-
Jet JJ-8CS - page 26
26 Cutterhead Assembly ...
-
Jet JJ-8CS - page 27
27 Cutterhead Assembly Index Part No. No. Description Size Qty . 1 ......... JC-C01 ............................. Cutterhead ........................................................................ ...................... 1 2 ......... JC-C02 ............................. Bearing Housing .............................................................. ...
-
Jet JJ-8CS - page 28
28 Wiring Diagram ...
Avez-vous une question à propos de Jet JJ-8CS?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Jet JJ-8CS, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Jet JJ-8CS il est probable qu’il a envie de partager la façon de le résoudre.