-
Sharp FU-40SE-K - page 1
R FU-40SE-K Ta b letop / wall-mounting type AIR PURIFIER OPERA TION MANU AL ...
-
Sharp FU-40SE-K - page 2
...
-
Sharp FU-40SE-K - page 3
FEA TURES Cluster Ion Contr ol The unit controls the ratio of minus cluster ions and plus cluster ions depending on the condition of the room. • Clean mode Appro ximately the same amount of plus and minus cluster ions are discharged. This mode is eff ective f or reducing floating mold and household odors in the air . • Refresh mode It is said t ...
-
Sharp FU-40SE-K - page 4
• Do not use the unit if the power cord or plug is damaged or the connection to the wall outlet is loose. Electrical shock, shor t circuit and/or fire ma y occur as a result. • Do not damage, break, coat, f orcefull y bend, pull, twist, bundle, pinch or place hea vy objects on the power cor d. If the pow er cord is damaged, fire and/or electric ...
-
Sharp FU-40SE-K - page 5
CA UTIONS CONCERNING THE USA GE OF THIS PR ODUCT • Do not bloc k the intake and exhaust ports. • Do not use the unit near or on hot objects, such as a sto ve, etc. Also , do not use the unit where it ma y come into contact with steam. • Do not use the unit on its side. Def ormation, malfunction and/or overheating of the motor ma y occur as a ...
-
Sharp FU-40SE-K - page 6
Plasmacluster NAMES OF P AR TS MAIN UNIT DISPLA Y Filter timer lamp AU TO operation lamp F an level lamps * T obacco smoke mode oper ation lamp Pollen mode operation lamp OFF timer displa y lamps (set using remote control) Po w er lamp (Lights when the power plug is inser ted into the w all outlet) Remote control receiver Odor sensor (Detects odors ...
-
Sharp FU-40SE-K - page 7
AC CESSORIES Remote control (1 unit) Battery (AA batter y X 2 units) When used on a tabletop Stand (1 unit) Thumbscrew (2 units) Located on bottom of stand CLUSTER ION LAMP Cluster ion operation is selected using the remote control. Blue light When the cluster ion operation is in the Clean mode or A UT O cluster ion mode and the air in the room is ...
-
Sharp FU-40SE-K - page 8
INST ALLA TION WHEN USING THE UNIT ON A T ABLET OP FIXING THE ST AND 1 Remove the fr ont panel. • At this time, also remo ve the pre-filter , stamina-pow er carbon and the HEP A filter . Front panel 2 Place the unit with its front side facing down on a flat and stable surface. • Place a soft cloth, etc., to prevent damaging the unit. 3 Insert t ...
-
Sharp FU-40SE-K - page 9
Mount the brac k et to the back of the main unit using the small scre ws included. 3 Place the cushions as sho wn 4 Mount the main unit (1) Align the horizontal positions of mounting brack ets 1 and 2 and hook the brack et 2 to brack et 1. (2) Hold the bottom of the main unit, pull the unit to- w ards y ou and then pull down. 5 Chec k the installat ...
-
Sharp FU-40SE-K - page 10
PREP ARA TION Be sure to remove the power plug from the wall outlet. INST ALLING THE FIL TERS To maintain the quality of the filters, the y are installed in the main unit within polyvinyl bags . Be sure to remove the filters from the polyvinyl bags before using the unit. 1 Remove the filters 1 Place the unit facing up Place the unit on a table, etc ...
-
Sharp FU-40SE-K - page 11
2 Install the filter 1 Remo ve the HEP A filter from the polyvinyl bag and install it in the main unit with the display facing up. Inser t so that the tabs on the HEP A filter are f acing you. Proper operation cannot be achie v ed if installed incorrectly . USING THE REMOTE CONTROL HEP A filter T abs 2 Remove the stamina-power car- bon from the pol ...
-
Sharp FU-40SE-K - page 12
OPERA TION MAIN UNIT OPERA TION The unit will start operation when the MODE-ON/OFF button is pressed. (The unit will star t oper ation in A UTO mode) • During operation, the cluster ion lamp will light. (During star t of operation, the cluster ion mode will be A UT O) The operation mode suitab le for the usa ge condition can be set. Stop AU TO op ...
-
Sharp FU-40SE-K - page 13
REMOTE CONTROL OPERA TION •T o star t operation, press the ON/OFF b utton. A short beep will sound and operation will start in the AU TO mode. •T o stop operation, press the ON/OFF b utton again. A long beep will sound and operation will stop. T ransmitter Manual (fan level) button The fan level can be switched between Silent, Median, High and ...
-
Sharp FU-40SE-K - page 14
CARE AND MAINTENANCE (T o maintain the best perf ormance of this product, please clean the unit per iodically .) When cleaning, be sure to remove the power plug from the wall outlet. In addition, never handle the power plug with wet hands. Electrical shock and/or bodily injury may occur as a result. MAIN UNIT For soiling on the main unit and the in ...
-
Sharp FU-40SE-K - page 15
Guide for filter replacing timing • The f ollo wing is a guide from JEM 1467 b y Japan Electrical Manuf acturers Association in Japan, and in JEM 1467, the replacement period is set as when smoking 10 cigarettes per da y and the dust collection/deodorization power is reduced b y half that of new filters . • HEP A filter About 5 years after open ...
-
Sharp FU-40SE-K - page 16
TROUBLESHOOTING Before calling f or repair , chec k the symptoms below f or possib le remedies, since the problem ma y not be a malfunction of the unit. SYMPT OM REMEDY (not a malfunction) The remote contr ol does not w ork •H av e the batteries depleted? • Are the batteries inser ted correctly? • Is a fluorescent lighting in the room flick e ...
Avez-vous une question à propos de Sharp FU-40SE-K?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Sharp FU-40SE-K, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Sharp FU-40SE-K il est probable qu’il a envie de partager la façon de le résoudre.