Français dropdown-ico

Manuel d’utilisation Husqvarna 326EX

24 pages 0.93 mb
Télécharger

Aller à la page of 24

Summary
  • Husqvarna 326EX - page 1

    326E X-SERIES Operator’ s manual (CARB II, EP A II) 114 00 19-93 Read through the Operator‘s manual carefully and understand the content before using the machine. ...

  • Husqvarna 326EX - page 2

    2 – English Symbols • Warning! The blade continues to rotate even after the engine has stopped. When the engine has stopped, stop the blade from rotating by letting the blade come in contact with the ground. Indicates the direction of rotation. SYMBOL EXPLANA TION WARNING! The edger can be dangerous! Careless or incorrect use can result in seri ...

  • Husqvarna 326EX - page 3

    English – 3 List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS Personal protective equipment ............................................ 4 The machine‘s ...

  • Husqvarna 326EX - page 4

    4 – English The machine ‘ s safety equipment This section describes the machine ‘ s safety equipment, its function and how checks and maintenance are carried out to ensure that it operates correctly. (See the chapter “ What is what “ to locate where this equipment is positioned on your machine.) Personal protective equipment 3. Cutting at ...

  • Husqvarna 326EX - page 5

    English – 5 6. Cutting equipment The blade is designed and machined for coping with the wear that cutting the edges of lawns involves. 7. Locking nut The locking nut secures the cutting equipment on the output shaft. 5. Muffler The muffler is designed to give the lowest possible noise level and to direct the engine ‘ s exhaust fumes away from t ...

  • Husqvarna 326EX - page 6

    6 – English 3. Cutting attachment guard • Ensure that the guard is undamaged and not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" . Control, maintenance and service of the machine ‘ s safety equipment IMPORTANT IN ...

  • Husqvarna 326EX - page 7

    English – 7 Two basic rules: 1) Only use the cutting and guard equipment we recommend! See chapter “ Technical data “ . 2) Check the cutting equip- ment with regard to damage and crack formation. Damaged cutting equipment should always be replaced. 7. Locking nut • Protect your hand from injury when assembling, use the blade guard as protec ...

  • Husqvarna 326EX - page 8

    8 – English Safety instructions before starting work • Inspect the working area. Remove loose objects such as stones, broken glass, nails, steel wire, string, etc. that can be thrown or become entangled in the blade or blade guard. • Keep unauthorised persons at a distance. Children, animals, onlookers and helpers should be outside the safety ...

  • Husqvarna 326EX - page 9

    English – 9 Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like. • When storing and transporting fuel approved containers intended for t ...

  • Husqvarna 326EX - page 10

    10 – English Basic safety precautions 1. Observe your surroundings: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that the above mentioned do not come into contact with the cutting equipment or objects that can be thrown by the cutting equipment. • NOTE! Never use a machine without t ...

  • Husqvarna 326EX - page 11

    English – 11 SAFETY INSTRUCTIONS Safety instructions after completing work • Ensure the blade has stopped before cleaning, carrying out repairs or an inspection. Remove the spark plug cable from the spark plug. • Wear heavy-duty gloves when carrying out repairs on the edger. • Store the machine out of reach of children. • Only use origina ...

  • Husqvarna 326EX - page 12

    English – 12 WHA T IS WHA T? What is what on the edger? 1. Blade 2. Grease filler cap 3. Angle gear 4. Blade guard 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Cylinder cover 11. Starter handle 12. Fuel tank 13. Choke 14. Air purge 15. Air filter cover 16. Clutch cover 17. Handlebar adjustment 18. Locking nut ...

  • Husqvarna 326EX - page 13

    English – 13 Assembling the blade Fit the blade as follows: 1. Fit the drive disc (A) on the outgoing shaft. Make sure that the edge that fits in the hole of the blade is facing outward. 2. Block the blade rotation by inserting locking pin in the hole behind the blade guard engaging it in the corresponding hole in the drive disc. 3. Fit the blade ...

  • Husqvarna 326EX - page 14

    English – 14 NOTE! The edger is fitted with two-stroke engines and must always be run on a mixture of gasoline and two-stroke oil. To ensure the correct mixture proportions it is important to measure the quantity of oil accurately. When mixing small amounts of fuel small discrepancies in the amount of oil has a great bearing on the proportions of ...

  • Husqvarna 326EX - page 15

    English – 15 Control before starting WARNING! When the engine starts with the choke lever in the choke or starter throttle position the cutting tool (blade or trimmer) starts to rotate immediately. ST ART AND ST OP For reasons of safety follow these recommendations! • Check that the support flange is not cracked due to fatigue or due to being t ...

  • Husqvarna 326EX - page 16

    English – 16 Fine adjustment • When the machine has been ”run-in” the carburetor should be finely adjusted. The fine adjustment should be carried out by qualified person. First adjust the L-jet, then the idling screw T and then the H-jet. Conditions • Before any adjustments are made the airfilter should be clean and the airfilter cover fi ...

  • Husqvarna 326EX - page 17

    English – 17 Correctly adjusted carburetor A correctly adjusted carbur etor means that the machine accelerates without hesitation and the machine 4-cycles a little at max speed. F urthermor e, the cutting attachment must not rotate/mo ve at idling. A too lean adjusted low speed needle L may cause starting difficulties and bad acceleration. A too ...

  • Husqvarna 326EX - page 18

    English – 18 A muffler fitted with a catalytic converter reduces the extent of the following substances in the exhaust fumes: • Hydrocarbons (HC). Some hydrocarbons in gasoline and the exhaust are carcinogenic. • Nitric oxides (NO). Irritating for the breathing air-ways. • Aldehydes. The most common formaldehyde, is carcinogenic and causes ...

  • Husqvarna 326EX - page 19

    English – 19 Lubricating the flexible drive axle Adjusting the edger ‘ s cutting depth MAINTENANCE Inside the edger ‘ s drive shaft is a flexible drive axle. The flexible drive axle should be regularly lubricated after 30 hours of operation. Loosen the two screws on the angle gear and remove it. The flexible drive axle is easily removed from ...

  • Husqvarna 326EX - page 20

    English – 20 NOTE: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQVARNA. Maintenance schedule Below you will fin ...

  • Husqvarna 326EX - page 21

    English – 21 TECHNICAL D A T A T echnical data Engine Cylinder capacity, cu. in/cm 3 Cylinder bore, inch/mm Stroke length, inch/mm Recommended max. speed, rpm Idling speed, rpm Speed of output axle, rpm Max. engine output, acc. to ISO 8893 Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition sy ...

  • Husqvarna 326EX - page 22

    English – 22 FEDERAL AND CALIFORNIA EMISSION CONTR OL W ARRANTY ST A TEMENT ´+H!•¶3l¨ WHAT IS COVERED REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding your warranty rights an ...

  • Husqvarna 326EX - page 23

    English – 23 ...

  • Husqvarna 326EX - page 24

    ´+H!•¶3l¨ 2001W22 ...

Fabricant Husqvarna Catégorie Trimmer

Les documents que nous recevons du fabricant de l'appareilHusqvarna 326EX peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Husqvarna
- manuels d’utilisations 326EX
- fiches produit Husqvarna
- dépliants
- ou étiquettes-énergie Husqvarna 326EX
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Husqvarna 326EX.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Husqvarna 326EX, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Husqvarna 326EX. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Husqvarna 326EX.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Husqvarna 326EX, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Husqvarna 326EX par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Husqvarna 326EX.

Le manuel d’utilisation complet Husqvarna, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Husqvarna 326EX - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Husqvarna 326EX, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHusqvarna 326EX qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Husqvarna 326EX - qui devraient nous aider dans les premières étapes lors de l'utilisation Husqvarna 326EX
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Husqvarna 326EX
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Husqvarna 326EX dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Husqvarna 326EX?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Husqvarna 326EX, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Husqvarna 326EX il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)