Français dropdown-ico

Manuel d’utilisation Hitachi CP-WX8255

33 pages 1.58 mb
Télécharger

Aller à la page of 33

Summary
  • Hitachi CP-WX8255 - page 1

    1 Projector CP-X8150/CP-X8160/CP-WX8240 CP-WX8255/CP-SX8350/CP-WU8440 CP-WU8450 User's Manual (detailed) Instant Stack Guide Thank you for purchasing this product. WARNING ►Before using this product, be sure to read all manuals for this product. After reading them, store them in a safe place for future reference. ►Follow all the instructio ...

  • Hitachi CP-WX8255 - page 2

    2    1. Introduction ........................ 3 1.1 Basic information and preparations ............................. 3 Instant Stack ........................................ 3 Intellectual Stack and Simple Stack ..... 3 Remote control for Intellectual Stack and Simple Stack ............................. 3 2. Installation ............... ...

  • Hitachi CP-WX8255 - page 3

    3 (continued on next page) 1. Introduction 1.1 Basic infor mation and prepar ations Instant Stack Instant Stack is a feature that allows you to superimpose images projected from two projectors easily . Intellectual Stack and Simple Stac k Instant Stack includes the following two features. When two projectors are connected via an RS-232C cable with ...

  • Hitachi CP-WX8255 - page 4

    4 Introduction 1.1 Basic information and preparations (continued) NO TICE ► Intellect ual Stack can be opera ted only in pairs of the same model projectors. ► A maximum of two projectors can be used as Intellectual Stack. ► Depending on the installation and surrounding environment, images projected from the two projectors may not superimpose ...

  • Hitachi CP-WX8255 - page 5

    5 For safety reasons, read 1.1 Basic information and preparations (  3, 4 ) carefully before installation. In addition, take note of the followings for proper use of Instant Stack. ● When using Intellectual Stack , both projectors will respond to the remote control signals until ST ACK MODE on either projector is set to SUB. If you control one ...

  • Hitachi CP-WX8255 - page 6

    6 Installation NOTE • Set the tilt angle of Set A to within 9 degrees from the level line. (continued on next page) Deciding installation position Decide the position of Set A and its projection angle. (  User ’s Manual (concise) → Arrangement and Adjusting the projector ’s elevator ) 2.2 Installing the r st projector (Set A ) Setting ...

  • Hitachi CP-WX8255 - page 7

    7 Installation 4. Display the menu with the MENU button. (  Operating Guide → Using the menu function ) 5. Use the ▲/▼/◄/► buttons to go into the following menu. ADV ANCED MENU > OPTION > SERVICE > COMMUNICA TION > ST ACK ST ACK menu will appear on screen. (  Operating Guide → OPTION menu ) NOTE • Set A will not be o ...

  • Hitachi CP-WX8255 - page 8

    8 Installation 2.3 Installing the second projector (Set B ) Connecting projector s T o use Intellectual Stack, connect an RS-232C cross cable between the CONTROL port of Set A and Set B . (continued on next page) NOTE • KEYST ONE cannot be operated when PERFECT FIT is in use. T o reset both functions, reset PERFECT FIT rst. • Perform the INS ...

  • Hitachi CP-WX8255 - page 9

    9 Installation 8. After pressing the ► button, a dialog to conrm whether or not to save the setting is displayed. Press the ► button to complete the setting. (  19 ) 6. Use the ▲/▼ buttons to highlight ST ACK MODE, and press the ► button to display the ST ACK MODE dialog. Highlight MAIN with the ▲/▼ buttons, and press the ◄ bu ...

  • Hitachi CP-WX8255 - page 10

    10 Installation 2.4 Conr ming Main and Sub settings NO TE • When Intellectual Stack is in use, only Main is capable of receiving the remote control signals, Sub will not respond to the remote control signals. 2. The following dialogs appear on the lower right screen. Main (Set B ) Sub (Set A ) 3. If you press the ► button, the dialog closes ...

  • Hitachi CP-WX8255 - page 11

    1 1 Installation 2.5 Fine adjusting image position T o superimpose the images of Main (Set B ) and Sub (Set A ), ne adjust the im- age size and position of Main (Set B ) using PERFECT FIT . 3. Using PERFECT FIT on Main (Set B ), adjust the im- age size and position of Main (Set B ) to superimpose well to the image of Sub (Set A ). (  Operatin ...

  • Hitachi CP-WX8255 - page 12

    12 Installation NOTES f or all user s • For details on PERFECT FIT , refer to PERFECT FIT of EASY MENU or SETUP menu in the Operating Guide . • It is strongly recommended to use a at screen. If a curved or skewed screen is used, it is very difcult to align the two images even if you use the pin/barrel adjustment of PERFECT FIT . • Even ...

  • Hitachi CP-WX8255 - page 13

    13 3.1 Displaying ST ACK menu Use the ▲/▼/◄/► buttons to go into the following menu. ADV ANCED MENU > OPTION > SERVICE > COMMUNICA TION > ST ACK ST ACK menu will appear on screen. (  Operating Guide → OPTION menu ) The setting for Intellectual Stack operation starts from this menu. Set the Intellectual Stack operation using ...

  • Hitachi CP-WX8255 - page 14

    14 ST ACK menu settings NOTE • After setting Main or Sub, the setting information can be checked on Projector Web Control. (  Network Guide → Projector Web Control ) Select Projector Status in the main menu of Projector Web Control. The Stack Mode item shows whether your projector is set to MAIN or SUB even if ST ACK MODE is set to OFF . 3. ...

  • Hitachi CP-WX8255 - page 15

    15 ST ACK menu settings 3. Press the ◄ button to return to the previous menu, or press the ► button to complete the setting. (  19 ) NOTE • If DUAL is selected, a menu to select MAIN or SUB appears on screen when a button on the control panel of the projector or remote control is pressed. Select the projector that you want to operate. Refe ...

  • Hitachi CP-WX8255 - page 16

    16 ST ACK menu settings NO TE • When DUAL is selected for LAMP MODE, the images projected from the Main and Sub projectors may be different. It is recommended to set the projectors as follows. - Set the same image for TEMPLA TE and ST ART UP on the Main and Sub projectors. - Capture the same image for MyScreen on the Main and Sub projectors. - Sa ...

  • Hitachi CP-WX8255 - page 17

    17 ST ACK menu settings 3. Press the ◄ button to return to the previous menu, or press the ► button to complete the setting. (  19 ) NOTE • The AL TERNA TE MODE dialog can be operated on the Main projector when AL TERNA TE is selected in the LAMP MODE dialog. • T o maintain the quality and reliability of the two projectors, the projector ...

  • Hitachi CP-WX8255 - page 18

    18 ST ACK menu settings 3. Press the ◄ button to return to the previous menu, or press the ► button to complete the setting. (  19 ) NOTE • <Only for CP-WU8440 and CP-WU8450 > When the projectors are in the PbyP mode, the SUB INPUT SOURCE is xed at FOLLOW MAIN UNIT . • If FIXED (COMPUTER IN 1) is selected, either the COMPUTER IN ...

  • Hitachi CP-WX8255 - page 19

    19 ST ACK menu settings Before exiting menu operation for Intellectual Stack, it is recommended to check all the settings in the ST ACK menu. For dialogs that are called from the ST ACK menu, you can press the ◄ button to return to the ST ACK menu. Refer to the following to exit menu operation for Intellectual Stack. 3.6 Exiting Intellectual Stac ...

  • Hitachi CP-WX8255 - page 20

    20 ST ACK menu settings (continued on next page) 3.7 Impor tant infor mation f or Intellectual Stack This section provides important information for setting up the Main and Sub projectors, not explanations on operating the menus. Read all information carefully . ● T o use Intellectual Stack, one projector must be set to Main and the other set to ...

  • Hitachi CP-WX8255 - page 21

    21 ST ACK menu settings ● The Main and Sub projectors have the following common settings. - A V MUTE (  Operating Guide → T emporarily turning off the screen an d audio ) - Magnifying feature (  Operating Guide → Using the magnify feature ) - ASPECT and OVER SCAN (  Operating Guide → IMAGE menu ) - COMPUTER IN (  Operating Guide ...

  • Hitachi CP-WX8255 - page 22

    22 ST ACK menu settings Example: Cover Error: Lamp cover is opened. Lamp Error: Lamp does not light up. Fan Error: Problem with cooling fan. T emp Error: T emperature of the projector is too high. Air Flow Error: T emperature of the projector is too high, check that the exhaust vents are not blocked. Filter Error: The reading on the lter timer e ...

  • Hitachi CP-WX8255 - page 23

    23 T o superimpose two images onto one screen, the same image must be input to the Main and Sub projectors. There are various methods to input the image to the projectors. This chapter describes the ways of connecting the cables. Read this chapter to nd a method that meets your needs. 4.1 Connecting an RS-232C cable If you are using Intellectual ...

  • Hitachi CP-WX8255 - page 24

    24 Connecting cables Inputting image to Sub and Main individuall y 1. Split the output signal from your image device into two with device such as a signal splitter . 2. Connect the output ports of the image output device to the same input ports on the Main and Sub projectors. NO TES for Simple Stac k • COMPUTER IN1 and IN2 can be used as the inpu ...

  • Hitachi CP-WX8255 - page 25

    25 5.1 Preparing for menu operations If Simple Stack without an RS-232C connection is used, press the button corresponding to the port on the remote control or the INPUT button on the projector to select the port to which the cable is connected. For setting of MONITOR OUT , refer to SETUP menu in Operating Guide . This completes the setting. If Int ...

  • Hitachi CP-WX8255 - page 26

    26 Setting input por ts using menu 5.3 Star ting up Main projector After performing section 5.2 Checking Main projector's operating status , the two projectors are conrmed to have been set to AL TERNA TE mode and the Sub projector is currently operating. As the settings for Intellectual Stack can be changed only when the Main projector is o ...

  • Hitachi CP-WX8255 - page 27

    27 Setting input por ts using menu 5.4 Setting the menu If Intellectual Stack with RS-232C connection is used, observe the followings. When inputting image signa ls to Sub via Main, the oper ations diff er between using computer signals and video signals such as component and video signals. Inputting image fr om Main to Sub - Computer signal 1. If ...

  • Hitachi CP-WX8255 - page 28

    28 Setting input por ts using menu Inputting image fr om Main to Sub - Video signal (either component or video) 1. If the ST ACK menu is already displayed on the screen, proceed to 3 below . Otherwise press the MENU button on the remote control. If the MENU dialog is displayed, use the ▲/▼ buttons to highlight MAIN, and press the ► button. A ...

  • Hitachi CP-WX8255 - page 29

    29 Setting input por ts using menu 5.4 Setting the menu - Inputting image to Sub and Main individually (continued) 3. Use the ▲/▼ buttons to highlight SUB INPUT SOURCE, and press the ► button to display the SUB INPUT SOURCE dialog. 4. Use the ▲/▼ buttons to highlight FOLLOW MAIN UNIT , and press the ► button to c omplete the set- ting. ...

  • Hitachi CP-WX8255 - page 30

    30 6. R estrictions on Schedule function This model supports the Schedule function on the Projector Web Control feature. (  Network Guide → 3.1.7 Schedule Settings ) There are some restrictions on the functions when Intellectual Stack with RS-232C connection is used. But for Simple Stack without an RS-232C connection, there is no restriction o ...

  • Hitachi CP-WX8255 - page 31

    31 Restrictions on Sc hedule function NOTE • If the Schedule is not executed, an error message will be sent in accordance with the conditions set in Schedule Execution Error on Projector Web Control. (  Network Guide → 3.1.6 Alert Settings ) • If the Schedule function is set to turn off the power when the projectors are operating in Intell ...

  • Hitachi CP-WX8255 - page 32

    32 7. T roubleshooting About the phenomenon confused with a machine defect, check and cope with it according to the following table. Phenomena that may be easy to be mistaken for machine defects Phenomenon Cases not involving a machine defect Reference page Intellectual Stack does not function. No power is supplied to the Main and Sub projector . T ...

  • Hitachi CP-WX8255 - page 33

    33 T r oubleshooting The ST ACK menu cannot function. The settings on the projectors are not set for the Intellectual Stack feature. Check the following settings on the Main and Sub projectors. - ST ANDBY MODE in SETUP menu: NORMAL - COMMUNICA TION TYPE under COMMUNICA TION in SERVICE menu: OFF - ST ACK LOCK in SECURITY menu: OFF  5 The projecto ...

Fabricant Hitachi Catégorie Projector

Les documents que nous recevons du fabricant de l'appareilHitachi CP-WX8255 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Hitachi
- manuels d’utilisations CP-WX8255
- fiches produit Hitachi
- dépliants
- ou étiquettes-énergie Hitachi CP-WX8255
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Hitachi CP-WX8255.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Hitachi CP-WX8255, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Hitachi CP-WX8255. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Hitachi CP-WX8255.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Hitachi CP-WX8255, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Hitachi CP-WX8255 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Hitachi CP-WX8255.

Le manuel d’utilisation complet Hitachi, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Hitachi CP-WX8255 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Hitachi CP-WX8255, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHitachi CP-WX8255 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Hitachi CP-WX8255 - qui devraient nous aider dans les premières étapes lors de l'utilisation Hitachi CP-WX8255
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Hitachi CP-WX8255
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Hitachi CP-WX8255 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Hitachi CP-WX8255?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Hitachi CP-WX8255, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Hitachi CP-WX8255 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)