Manuel d’utilisation Pella 801U0103

10 pages 0.74 mb
Télécharger

Aller à la page of 10

Summary
  • Pella 801U0103 - page 1

    Installation Instructions for T ypical Wood F rame Construction. These instructions wer e developed and tested for use with typical wood frame wall construction in a wall system designed to manage water . These instructions ar e not to be used with any other construction method. Installa tion instructions for use with other construction methods, mu ...

  • Pella 801U0103 - page 2

    C. Cut the water resistive barrier (1C). See page 10 for additional cutting pat terns. D. F old the water r esistive barrier (1D). F old side flaps into the opening and staple to inside wall. F old top flap up and temporarily fasten with flashing tape. E. Apply sill flashing tape #1. Cut a piece of flashing tape 12" longer than the openin ...

  • Pella 801U0103 - page 3

    A. Install and level shims. Place 1" wide by 1/4" thick shims on the bottom of the opening, 2-1/2" fr om each side, beneath transition bars and mullion joints. K eep shims back 1/2" from interior face of window. Adjust shims as necessary to ensure the sill is level. Once level, at tach shims to prevent movement. Note: Improper p ...

  • Pella 801U0103 - page 4

    F. Insert the window from the e xterior of the building. Place the bottom of the window on the spacers at the bottom of the opening, then tilt the top into position. C enter the window between the sides of the opening to allow clearance for shimming. Windows with nail fin: Insert one roofing nail in the first hole fr om the corner on each end of ...

  • Pella 801U0103 - page 5

    A. Units that do not have pre-applied fin corners: Cut four pieces of flashing tape 1-1/2" long. Apply one piece of flashing tape to each end of the sill fin so that it extends 1-1/2" past the end of the sill fin. Apply one piece of flashing tape to the bottom end of each flexible fin, beginning 1-1/2" from the end of the fi ...

  • Pella 801U0103 - page 6

    D. F old down top flap of water resistive barrier (3D). E. Apply flashing tape to diagonal cuts. Cut pieces of flashing tape at least 1" longer than the diagonal cuts in the water resistive barrier . Apply the tape covering the entire diagonal cut in the water resistive barrier a t both upper corners of the window . If vertical cuts were al ...

  • Pella 801U0103 - page 7

    4 SECURING THE WINDOW A. Install a #10 x 3-1/2" corrosion resistant wood scr ew into each pre- drilled screw hole. Note: Minimum 1-1/4" embedment into the wall framing is requir ed. P roceed to S tep 6. Ř ALL WINDOWS Ř ALL WINDOWS Ř 5 INST ALLA TION CLIP METHOD A. F asten the window to the opening by driving two #6 x 1-1/2" ...

  • Pella 801U0103 - page 8

    7 SEALING THE WINDOW TO THE EXTERIOR WALL CLADDING When applying siding, brick veneer or other e xterior finish material, leave adequate space between the window frame and the ma terial for sealant. Refer to the illustration tha t corresponds to your finish material. Note: T he sealant details shown are standar d recommendations fr om the sealant ...

  • Pella 801U0103 - page 9

    A. Insert closed cell foam backer r od into the space around the window so ther e is approxima tely 3/8" clearance between the backer r od and the exterior face of the window. Note: Backer rod adds shape and depth for the sealant line. x x B. Apply a bead of high quality exterior gr ade sealant to the entire perimeter of the window . Not ...

  • Pella 801U0103 - page 10

    EXTERIOR FINISH The exterior fr ame and sash are pr otected by aluminum cladding with our EnduraClad® or EnduraClad Plus baked-on factory finish tha t needs no painting. Clean this surface with mild soap and water . Stubborn stains and deposits may be r emoved with mineral spirits. DO NO T use abrasives. DO NO T scr ape or use tools that might da ...

Fabricant Pella Catégorie Window

Les documents que nous recevons du fabricant de l'appareilPella 801U0103 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Pella
- manuels d’utilisations 801U0103
- fiches produit Pella
- dépliants
- ou étiquettes-énergie Pella 801U0103
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Pella 801U0103.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Pella 801U0103, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Pella 801U0103. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Pella 801U0103.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Pella 801U0103, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Pella 801U0103 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Pella 801U0103.

Le manuel d’utilisation complet Pella, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Pella 801U0103 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Pella 801U0103, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lPella 801U0103 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Pella 801U0103 - qui devraient nous aider dans les premières étapes lors de l'utilisation Pella 801U0103
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Pella 801U0103
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Pella 801U0103 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Pella 801U0103?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Pella 801U0103, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Pella 801U0103 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)