Français dropdown-ico

Manuel d’utilisation Peavey CS 1200X

22 pages 0.81 mb
Télécharger

Aller à la page of 22

Summary
  • Peavey CS 1200X - page 1

    ...

  • Peavey CS 1200X - page 2

    A lntended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. A Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the pr ...

  • Peavey CS 1200X - page 3

    A WARNING! For optimum performance and reliability DO NOT PRESENT THE AMPLIFIER WITH A SPEAKER LOAD OF LESS THAN 2 OHMS, OR A COMBINATION OF SPEAKERS THAT TOGETHER ARE LESS THAN 2 OHMS! Using one speaker, it must be rated at 2 ohms minimum. Using two speakers, they must be rated each at 4 ohms minimum. Using three speakers, they must be rated each ...

  • Peavey CS 1200X - page 4

    CHANNEL A lN!wT -- SEN!3TlVITY MADE IN U.S.A. CHANNEL 0 INPUT SENSITIVITY CS” 12ooz PROFESSIONAL STEREO POWER AMPLIFIER DDTTM ACTIVE LEDs (1) The DDTTM active LEDs indicate when compression is taking place. As long as gain reduction is occurring, the LED will continue to light, thereby giving a valuable indication of this unique compression funct ...

  • Peavey CS 1200X - page 5

    that particular channel. Operation at power output levels below 100% will naturally be indicated by lower LED readings. The lowest value indicated is 0.4% of full power, which corresponds to 2.0 watts RMS output into 4 ohms. Operation below that power level will not be indicated, since the lowest LED is calibrated at 0% or standby. As mentioned, th ...

  • Peavey CS 1200X - page 6

    A GRILLE (6) The back panel includes the fan opening with protective grille (6), where cooling air is drawn into the amplifier. This opening should never be blocked or restricted. DDT SWITCH (7) This switch is used to either ENABLE or DEFEAT the DDT compressor. Defeating the DDT compressor should not be performed lightly or simply as a matter of co ...

  • Peavey CS 1200X - page 7

    MODE SWITCH (10) The mode switch is located on the “back-porch” next to the channel input jacks. This switch converts the CS 1200X from normal stereo mode to bridge mode. Bridge-mode operation is very popular for commercial sound distribution systems (70/l 00 volt lines). A WARNING: In bridge mode, the CS 1200X is capable of delivering 1200 W R ...

  • Peavey CS 1200X - page 8

    amp channel or at the input of the PL-MODULE ELECTRONIC CROSSOVER when BIAMPING, the (PL-2) transformer must be inserted here. Otherwise a blank plug (PL- 1) is inserted in this socket. CROSSOVER INPUTS (13) These are the HIGH-Z INPUTS when an ELECTRONIC CROSSOVER module is installed. Two parallel input jacks are provided at this point, allowing fl ...

  • Peavey CS 1200X - page 9

    per channel or 4 ohms BRIDGE mode for any application. Operation at loads of 4 ohms per channel or 8 ohms BRIDGE mode is more desirable for sustained operation applications, be- cause the amplifier will run much cooler at this load. Operation above 4 ohms per channel and even open-circuit conditions can always be considered safe; however, sustained ...

  • Peavey CS 1200X - page 10

    OPERATION The CS 1200X is designed for maximum ease and flexibility of operation. When the unit is installed and connected as described in the previous sections, operation is as simple as turning on the mains switch (S), turning up the sensitivity controls (4) to the full clockwise setting, and then adjusting the associated mixer or pre-amplificati ...

  • Peavey CS 1200X - page 11

    2. STEREO MODE (BALANCED INPUTS) When conditions require the use of a balanced input at the power amplifier, the XLR connectors (11) on either or both channels can be converted to a balanced configuration by removing the jumper plug from the transformer accessory socket (12) and plugging in an input transformer module (PL-2). The Peavey model PL-2 ...

  • Peavey CS 1200X - page 12

    isolated (no longer connected to anything). In other words, the crossover modules and all associ- ated connectors (as well as the PL-2 transformers and respective XLR connectors) are islands unto themselves: in this case, two islands with each crossover having a balanced input (1 l), dual (parallel) unbalanced inputs (13), an unbalanced low output ...

  • Peavey CS 1200X - page 13

    mode. Remember, the 4-ohm minimum load must be connected between the red binding posts. If individual loads were connected to each output (as in normal stereo applications) when the bridge mode is selected. Channel A would supply a normal in-phase signal to its respective load, but Channel B would supply an abnormal out-of-phase signal to its respe ...

  • Peavey CS 1200X - page 14

    turn really is maximum compression range), the input sensitivity control should be set at Ihe maximum clockwise setting. This is always the best setting to start with. If, however, the ampti- fier is used in a small club, church, or studio application where the full-output capability of the power amplifier is seldom needed, or there is no need for ...

  • Peavey CS 1200X - page 15

    normal intermittent applications, low-speed fan operation will provide adequate cooling. Since the CS 1200X is a redundant two-channel amplifier, but only one fan is employed, the fan circuitry is an independent system, separately fused internally. You will notice that the heat sink components are divided horizontally. The lower half contains Chann ...

  • Peavey CS 1200X - page 16

    The result usually is severe clipping (distortion) of the high-frequency material. In a biamplified system, the high-frequency material is routed to its own power amplifier (and associated loud- speaker), which avoids the clipping problem. This results in an effective increase in system headroom that is greater than that which is obtained by simply ...

  • Peavey CS 1200X - page 17

    , 5. 6. ule. In this case, the associated XLR connector (11) is now unbalanced as per previous discussion. If desired, the parallel unbalanced phone jack inputs (13) may be used to supply signal to the crossover module. In addition, whenever the XLR connector on a particular crossover island is used (either balanced or unbalanced), the crossover in ...

  • Peavey CS 1200X - page 18

    SPECIFICATIONS Characteristics: (@ 120 V AC, 60 Hz) Output Power: (Typical Value) Stereo mode, both channels driven 2 ohms, 1 kHz, 1% THD 4 ohms, 1 kHz, 1% THD 8 ohms, 1 kHz, 1% THD Bridge mode, mono 4 ohms, 1 kHz, 1% THD 8 ohms, 1 kHz, 1% THD Rated Output Power: Stereo mode, both channels driven 4 ohms, 20 Hz to 20 kHz, 0.03% THD 8 ohms, 20 Hz to ...

  • Peavey CS 1200X - page 19

    k’requency Response: (Typical Value) Stereo mode, both channels driven +O, -1 dB, 1 W RMS, 4 ohms +O, -0.2 dB @ rated output, 4 ohms Damping Factor: (Typical Value) Stereo mode, both channels driven 4 ohms, 1 kHz Hum & Noise: Stereo Mode, both channels driven Below rated output power, 4 ohms Power Consumption: Stereo mode, both channels drive ...

  • Peavey CS 1200X - page 20

    CS42OOX PATCH DIAGRAMS Channel A Speakers Channel A (Shielded) Channel A Speakers Stereo Mode Channel B (ShIelded) PATCH DIAGRAM 1 Stereo Operation Unbalanced High Z Inputs (Typical Home Stereo) Channel A Channel A pL-2 (Balanced) Channei A Stereo Mode Jumper Plugs il Channel B (Balanced) PATCH DIAGRAM 2 Stereo Operation Balanced Low Z Inputs (Bala ...

  • Peavey CS 1200X - page 21

    THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA. ALL EXPORTED PRODUCTS ARE SUBJECT TO WARRANTY AND SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY. Ces clauses de garantie ne sont vaiables qu’aux Etats-Unis et au Canada. Dans tour les autres pays, les clauses de ga ...

  • Peavey CS 1200X - page 22

    IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric products, basic cautions should always be followed, including the following. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17 18 Read all safety and operating instructions before using this product. All safety and operating instructions should be retained for future reference. Obey ...

Fabricant Peavey Catégorie Stereo Amplifier

Les documents que nous recevons du fabricant de l'appareilPeavey CS 1200X peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Peavey
- manuels d’utilisations CS 1200X
- fiches produit Peavey
- dépliants
- ou étiquettes-énergie Peavey CS 1200X
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Peavey CS 1200X.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Peavey CS 1200X, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Peavey CS 1200X. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Peavey CS 1200X.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Peavey CS 1200X, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Peavey CS 1200X par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Peavey CS 1200X.

Le manuel d’utilisation complet Peavey, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Peavey CS 1200X - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Peavey CS 1200X, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lPeavey CS 1200X qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Peavey CS 1200X - qui devraient nous aider dans les premières étapes lors de l'utilisation Peavey CS 1200X
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Peavey CS 1200X
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Peavey CS 1200X dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Peavey CS 1200X?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Peavey CS 1200X, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Peavey CS 1200X il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)