Manuale per l’uso TP-Link TL-SG3424P

220 pagine 1.24 mb

Scarica

Vai alla pagina of 220

Prev Next

Summary

TP-Link TL-SG3424P - page 1

TL-SG3424P JetS tream L2 Managed PoE Switch Rev: 1.0.0 1910010613 ...
TP-Link TL-SG3424P - page 2

I COPYRIGHT & TRADEMARKS S pecifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., L TD. Other brands and product names are trademarks or registered trademarks of t heir respective holders. No part of the specificatio ns ma y be reproduced in any form or by any means or used to make any derivat ...
TP-Link TL-SG3424P - page 3

II CONTENTS Preface .............................................................................................................. 1 Chapter 1 Using the CLI ....................................................................................... 4 1.1 Accessi ng the CLI ................................................................................ ...
TP-Link TL-SG3424P - page 4

III show ma c-vlan .................................................................................................................. .... 21 Chapter 5 Protocol VLAN Commands ............................................................... 22 protocol-vla n template .................................................................................... ...
TP-Link TL-SG3424P - page 5

IV show lacp interface ............................................................................................................ .... 39 show lacp syst em-prior ity ...................................................................................................... 40 Chapter 10 User Manage Comma nds ........................................... ...
TP-Link TL-SG3424P - page 6

V arp detection trust- port ....................................................................................................... ... 59 arp detection (interfa ce)...................................................................................................... ... 60 arp detection limit-rate .................................................. ...
TP-Link TL-SG3424P - page 7

VI show radius account ing ......................................................................................................... 79 Chapter 15 Log Comma nds ................................................................................. 80 logging loca l buffe r ................................................................................. ...
TP-Link TL-SG3424P - page 8

VII system-tim e dst ................................................................................................................ ..... 97 ip addr ess ..................................................................................................................... ......... 98 ip management -vlan ............................................ ...
TP-Link TL-SG3424P - page 9

VIII Chapter 21 QoS Comma nds................................................................................ 1 17 qos ............................................................................................................................ .......... 1 17 qos dot1p config ......................................................................... ...
TP-Link TL-SG3424P - page 10

IX Chapter 25 ACL Comma nds ................................................................................137 acl time-s egm ent ............................................................................................................... .. 137 acl edit ti me-segm ent ............................................................................ ...
TP-Link TL-SG3424P - page 11

X igmp-snooping global .......................................................................................................... 1 61 igmp-snooping config .......................................................................................................... 1 61 igmp-snooping vlan -config-a dd .................................................. ...
TP-Link TL-SG3424P - page 12

XI show snmp view ................................................................................................................. . 186 show snmp group ................................................................................................................ 186 show snmp user ................................................................ ...
TP-Link TL-SG3424P - page 13

XII show cluste r neighb our........................................................................................................ 2 05 show cluster ntd p gl obal ...................................................................................................... 2 05 show cluster ntd p port-st atus ............................................. ...
TP-Link TL-SG3424P - page 14

1 Preface This Guide is intended for network administrator to provide referenced information about CLI (Command Line Interface). The device mentioned in this Guide stands for TL-SG3424P JetS tream L2 Managed PoE Switch. Overview of this Guide Chapter 1: Using the CLI Provide information about how to use the CLI, CLI Command Modes, Security Levels a ...
TP-Link TL-SG3424P - page 15

2 Provide information about the co mmands used for protecting the swit ch from the ARP cheating or ARP Att ack. Chapter 13: DoS Defend Command Provide information about the commands used for DoS defend and detecting the DoS attack. Chapter 14: IEEE 802.1X Commands Provide information about the commands us ed for configuring I EEE 802.1X function. C ...
TP-Link TL-SG3424P - page 16

3 Protocol). Chapter 27: IGMP Commands Provide information about the commands used for configuring the IGMP Snooping (Internet Group Management Protocol Snooping). Chapter 28: SNMP Commands Provide information about the commands used for configuri ng the SNMP (Simple Network Management Protocol) functions. Chapter 29: LLDP Commands Provide informat ...
TP-Link TL-SG3424P - page 17

4 Chapter 1 Using the CLI 1.1 Accessing the CLI Y ou can log on to the switch and access the CLI by the following two methods: 1. Log on to the switch by the console port on the switch. 2. Log on to the switch remotely by a T e lnet or SSH connection through an Ethernet port. 1.1.1 Logon by a console port T o log on to the switch by the console por ...
TP-Link TL-SG3424P - page 18

5 Figure 1-2 Connection Description 4. Select the port to connect in figure 1-3, and click OK . Figure 1-3 Select the port to connect 5. Configure the port selected in the step abov e as the following figure1-4 sho wn. Configure Bit s per second as 38400, Dat a bit s as 8, Parity as None, S top bit s as 1, Flo w control as None, and then click OK . ...
TP-Link TL-SG3424P - page 19

6 Figure 1-4 Port Settings 6. T ype the User name an d Password in the Hyper T erminal window , the factory default value for both of them is admin. The DOS pr ompt ” TP-LINK>” will appear after pressing the Enter button as figure1-5 shown. It indi cates that you can use the CLI now . Figure 1-5 Log in the Switch 1.1.2 Logon by Telnet T o lo ...
TP-Link TL-SG3424P - page 20

7 Figure 1-6 Open the Run window 3. T ype cmd in the prompt R un window a s figure 1-7 and click OK . Figure 1-7 Run Window 4. T ype telnet 192.168.0.1 in the command prompt shown as figure1-8, and press the Enter button. Figure 1-8 Connecting to the Switch ...
TP-Link TL-SG3424P - page 21

8 5. T ype the User name and Passwo rd (the factory default value fo r both of them is admin) and press the Enter button, then you can use the CLI now , which is shown as figure1-9. Figure 1-9 Log in the Switch 1.2 CLI Command Modes The CLI is divided into different command modes: User EXEC Mode, Privileged EXEC Mode, Global Configuration Mode, Int ...
TP-Link TL-SG3424P - page 22

9 User EXEC Mode Primary mode once it is connected with the swi tch. TP-LINK> Use the exit command to disconnect the switch (except that the switch is connected through the Consol e port). Use the enable command to access Privileged EXEC mode. Privileged EXEC Mode Use the enable command to enter this mode from User EXEC mode. TP-LINK# Use the ex ...
TP-Link TL-SG3424P - page 23

10 you should access the corres ponding command mode firstly. z Global Configuration Mode : In this mode, global commands are provided, such as the Spanning Tree, Schedule Mode and so on. z Interface Configuration Mode : In this mode, users can c onfigure one or several ports, different ports corresponds to dif ferent commands a). Interface Etherne ...
TP-Link TL-SG3424P - page 24

11 1.4 Conventions 1.4.1 Format Conventions The following conventions are used in this Guide: ¾ Items in square brackets [ ] are optional ¾ Items in braces { } are required ¾ Alternative items are grouped in braces and se parated by vertical bars. For example: speed {10 | 100 | 1000 } ¾ Bold indicates an unalterable keyword. For example: show l ...
TP-Link TL-SG3424P - page 25

12 Chapter 2 User Interface enable Description The enable command is used to access Privileged EXEC Mode from User EXEC Mode. Synt ax enable Command Mode User EXEC Mode Example If you have set the password to access Privileged EXEC Mode from User EXEC Mode: TP-LINK>enable Enter p assw ord ： TP-LINK# enable password Description The enable p ass ...
TP-Link TL-SG3424P - page 26

13 disable Description The disable command is used to return to User EXEC Mode from Privileged EXEC Mode. Synt ax disable Command Mode Privileged EXEC Mode Example Return to User EXEC Mode from Privileged EXEC Mode: TP-LINK# disable TP-LINK> configure Description The configure command is used to access Global Configuration Mode fr om Privileged ...
TP-Link TL-SG3424P - page 27

14 Command Mode Any Configuration Mode Example Return to Global Configuration Mode from Interface Configuration Mode,an d then return to Privileged EXEC Mode: TP-LINK(config-if)# exit TP-LINK(config)#exit TP-LINK# end Description The end command is used to return to Privileged EXEC Mode. Synt ax end Command Mode Any Configuration Mode Example Retur ...
TP-Link TL-SG3424P - page 28

15 Chapter 3 IEEE 802.1Q VLAN Commands VLAN (Virtual Local Area Network) technology is developed for the switch to divide the LAN into multiple logical LANs flexibly . Host s in the same VLAN can communicate with each other , regardless of their physical locations. VLAN can enhance performance b y conserving bandwidth, and improve security by limit ...
TP-Link TL-SG3424P - page 29

16 Create a VLAN, the vid of which is 12: TP-LINK(config)# vlan dat abase TP-LINK(config-vlan)#vlan 12 interface vlan Description The interface vlan command is used to access VLAN Interface Mode to configure the specified VLAN. Synt ax interface vlan vlan-id Parameter vlan-id ——VLAN ID,ranging from 1 to 4094. Command Mode Global Configuration M ...
TP-Link TL-SG3424P - page 30

17 TP-LINK(config-if)#description vlan2 switchport type Description The switchport type command is used to configur e the Link T ypes for the ports. Synt ax switchport type { access | trunk | general } Parameter access | trunk | general —— Link T ypes. There are three Link T ypes for the ports. Command Mode Interface Configuration Mode ( interf ...
TP-Link TL-SG3424P - page 31

18 TP-LINK(config-if)# switchport allowed vlan add 2 switchport pvid Description The switchport pvid command is used to configur e the PVID for the switch ports. Synt ax switchport pvid vlan-id Parameter vlan-id —— VLAN ID, ranging from 1 to 4094. Command Mode Interface Configuration Mode (interface ethernet / interface ran ge ethernet ) Exampl ...
TP-Link TL-SG3424P - page 32

19 show vlan Description The show vlan command is used to display t he information of IEEE 802.1Q VLAN . Synt ax show vlan [ vlan-id ] Parameter vlan-id —— VLAN ID, ranging from 1 to 4094. By default , display all the information of IEEE 802.1Q VLAN. Command Mode Any Configuration Mode Example Display the information of vlan 5: TP-LINK(config)# ...
TP-Link TL-SG3424P - page 33

20 Chapter 4 MAC VLAN Commands MAC VLAN (Virtual Local Area Network) is the way to classify the VLANs based on MAC Address. A MAC address is relative to a single VLAN ID. The untagged packets and the priority-tagged packet s coming from the MAC address will be tagged with this VLAN ID. mac-vlan add Description The mac-vlan add command is used to cr ...
TP-Link TL-SG3424P - page 34

21 Example Delete the existing MAC-Based VLAN entry with the MAC address of 00:00:00:00:00:02: TP-LINK(config)# mac-vlan remove 00:00:00:00:00:02 mac-vlan modify Description The mac-vlan modify command is used to modify the settings of t he subsistent MAC VLAN entry . Synt ax mac-vlan modify { vlan-id } { mac-addr } [ description ] Parameter vlan-i ...
TP-Link TL-SG3424P - page 35

22 Chapter 5 Protocol VLAN Commands Protocol VLAN (V irtual Local Area Network) is the way to classify VLANs based on Protocols. A Protocol is relative to a single VLAN ID. The untagged p ackets and the priority-tagged pa ckets matching the protocol template w ill be tagged with this VLAN ID. protocol-vlan template Description The protocol-vlan tem ...
TP-Link TL-SG3424P - page 36

23 protocol-vlan vlan vid template index member-list no protocol-vlan entry-id Parameter vid ——VLAN ID ， ranging from 1-4094. index ——The number of the Protocol template.Y ou can get the template corresponding to the number by the show protocol-vlan template command. entry-id ——The number of the Protocol VL AN . Y ou can get the Proto ...
TP-Link TL-SG3424P - page 37

24 show protocol-vlan vlan Command Mode Any Configuration Mode Example Display information of the protocol-vlan entry: TP-LINK(config)# show protocol-vlan vlan ...
TP-Link TL-SG3424P - page 38

25 Chapter 6 Voice VLAN Commands V oice VLANs are configured spec iall y for voice data stream. By configuring V oice VLANs and adding the ports with voice devic es attached to voice VLANs, you can perform QoS-related configuration for voice data, ens uring the transmission priority of voice data stream and voice quality . voice-vlan enable Descrip ...
TP-Link TL-SG3424P - page 39

26 Parameter aging-time ——Aging time (in minutes) to be set for the V oice VLAN. It ranges from 1 to 43200 and the default value is 1440. Command Mode Global Configuration Mode Example Set the aging time for the V oice VLAN as 2880 minutes: TP-LINK(config)# voice-vlan aging-time 2880 voice-vlan priority Description The voice-vlan priority comma ...
TP-Link TL-SG3424P - page 40

27 voice-vlan oui remove mac-addr Parameter mac-addr —— The OUI address of the voice device. mask-addr —— The OUI address ma sk of the voice device. description ——Give a description to the OU I for identification which contains 16 characters at most. By default, it is empty . Command Mode Global Configuration Mode Example Create a V oic ...
TP-Link TL-SG3424P - page 41

28 switchport voice-vlan security Description The switchport voice-vl an security command is used to configure the V oice VLAN security mode. Synt ax switchport voice-vlan securit y {disable | enable} Parameter disable | enable —— disable/enable the security mode for the specified port . Command Mode Interface Configuration Mode （ interface e ...
TP-Link TL-SG3424P - page 42

29 The show voice-vlan oui command is used to display the configuration information of V oice VLAN OUI. Synt ax show voice-vlan oui Command Mode Any Configuration Mode Example Display the configuration info rmation of V oice VLAN OUI: TP-LINK(config)# show voice-vlan oui show voice-vlan switchport Description The show voice-vlan switchport command ...
TP-Link TL-SG3424P - page 43

30 Chapter 7 GVRP Commands GVRP (GARP VLAN registration protocol) is an implementation of GARP (generic attribute registration protocol). GVRP allo ws the switch to automatically add or remove the VLANs via the dynamic VLAN registration information and propagat e the lo cal VLAN registration information to other switches, without having to individu ...
TP-Link TL-SG3424P - page 44

31 Example Enable the GVRP function for ports 2-6: TP-LINK(config)# interface range ethernet 2-6 TP-LINK(config-if)# gvrp gvrp registration Description The gvrp registration command is used to confi gure the GVRP registration type on the desired port. T o restore to the default value, ple ase use no gvrp registration command. Synt ax gvrp registrat ...
TP-Link TL-SG3424P - page 45

32 Parameter leaveall | join | leave —— They are the three timers: leave All 、 join and leave. Once the LeaveAll T imer is set, the port with GVRP enabled can send a LeaveAll message after the timer times ou t, so that other GARP ports can re-register all the attribute information. After that, the LeaveAll timer will start to begin a new cycl ...
TP-Link TL-SG3424P - page 46

33 TP-LINK(config)# show gvrp global show gvrp interface Description The show gvrp interface command is used to displa y the GVRP configuration information of the s pecified Ethernet ports. Synt ax show gvrp interface [ ethernet port-num ] Parameter port-num ——The Ethernet port number . By default, the GVRP configuration information of all the ...
TP-Link TL-SG3424P - page 47

34 Chapter 8 LAG Commands LAG (Link Aggregation Group) is to combine a number of ports together to make a single high-bandwidth data path, which can highly exte nd the bandwi dth. The bandwid th of the LAG is the sum of bandwidth of it s member port. interface link-aggregation Description The interface link-aggregation command is used to access the ...
TP-Link TL-SG3424P - page 48

35 interface range link-aggregation group-list no interface range link-aggregation group-list Command Mode Global Configuration Mode Parameter group-list ——The aggregation group list. Y ou can configure some aggregation groups at the same time. Example Access the Interface range Link -aggregation Mode and configure the aggregation group 1,4-6: ...
TP-Link TL-SG3424P - page 49

36 link-aggregation hash-algorithm Description The link-ag gregation hash-algorithm command is used to configure the Aggregate Arithmetic for LAG . Synt ax link-aggregation hash-algorithm { src_dst_mac | src_dst_ip } Parameter src_dst_mac —— The so urce and des tination MAC addresses. src_dst_ip ——The source and destination IP addresses. Co ...
TP-Link TL-SG3424P - page 50

37 TP-LINK(config)# interface link-aggregation 1 TP-LINK(config-if)# description movie server show interfaces link-aggregation Description The show interfaces link-aggrega tion command is used to display the configuration information of the A ggregate Arithmetic and the aggregation groups. Synt ax show interface link-aggregation [ group- num ] Para ...
TP-Link TL-SG3424P - page 51

38 Chapter 9 LACP Commands LACP (Link Aggregation Control Prot ocol) is defined in IEEE802.3ad and en ables the dynamic link aggregation and disaggregation by ex changing LACP packet s with its pa rtner . The switch can dynamically group similarly configured ports into a single logical link, which will highly extend the bandwidth and flexibly balan ...
TP-Link TL-SG3424P - page 52

39 Command Mode Interface Configuration Mode （ interface ethernet / interface range ethernet ） Example Configure the admin key of port 1 as 1024: TP-LINK(config)# interface ethernet 1 TP-LINK(config-if)# lacp admin-key 1024 lacp port-priority Description The lacp port-priority command is used to set the port priority for a port. T o restore to ...
TP-Link TL-SG3424P - page 53

40 Parameter port-num —— The Ethernet port number . By default, display the configuration information of all the Ethernet ports. Command Mode Any Configuration Mode Example Display the configuration inform ation of all the Ethernet ports: TP-LINK(config)# show lacp interface show lacp system-priority Description The show lacp system-priority co ...
TP-Link TL-SG3424P - page 54

41 Chapter 10 User Manage Commands User Manage Commands are used to configure the user name and password for users to log on to the Web management p age with a certain access level so as to protect the settings of the switch from being randomly changed. user add Description The user add command is used to add a new user . Synt ax user add user-name ...
TP-Link TL-SG3424P - page 55

42 user remove Description The user remove command is us ed to delete an existing user . The curr ent user can't be deleted by itself. Synt ax user remove user -name Parameter user-name —— An existing user name. Command Mode Global Configuration Mode Example Delete the user named tplink: TP-LINK(config)# user remove tplink user modify stat ...
TP-Link TL-SG3424P - page 56

43 user modify type Description The user modify type command is used to modify the acce ss level for the existing user . The current user can't be modified by itself. Synt ax user modify ty pe user-name {guest | admin} Parameter user-name —— The existing user name. guest | admin —— Access level. Guest: limited user; admin: manager . Co ...
TP-Link TL-SG3424P - page 57

44 Example Modify the password of tplink as newpwd: TP-LINK(config)# user modify p assword tplink p assword newpwd newpw d user access-control disable Description The user access-control disable command is used to cancel the user access-control. Synt ax user access-control disable Command Mode Global Configuration Mode Example Cancel the user acces ...
TP-Link TL-SG3424P - page 58

45 TP-LINK(config)# user access-control ip-based 192.168.0.148 255.255.255.255 user access-control mac-based Description The user access-contro l mac-based command is used to limit the MAC Address of the users for login. Only the user with this MAC Address you set here is allowed for login Synt ax user access-control mac-based mac-addr Parameter ma ...
TP-Link TL-SG3424P - page 59

46 Example Enable the access-control of the ports 2, port4, port5, port6,and port8: TP-LINK(config)# user access-control port-based 2,4-6,8 user max-number Description The user max-number command is used to configur e the number of the users logging on at the same time. T o cancel the limit to the num bers of the users loging in, please use no user ...
TP-Link TL-SG3424P - page 60

47 user idle-timeout minutes no user idle-timeout Parameter minute ——The timeout time, ranging from 5 to 30 in minites. By default, the value is 10. Command Mode Global Configuration Mode Example Configure the timeout time of the switch as 15 minites: TP-LINK(config)# user idle-timeout 15 show user account-list Description The show user account ...
TP-Link TL-SG3424P - page 61

48 Command Mode Any Configuration Mode Example Display the security configurat ion information of the users: TP-LINK(config)# show user configuration ...
TP-Link TL-SG3424P - page 62

49 Chapter 11 Binding Table Commands Y ou can bind the IP address, MAC address, VLAN and the connected Port number of the Host together , whic h can be the condition for the ARP Inspection to filter the pa ckets. binding-table user-bind Description The binding-t able user-bind command is used to bind the IP address, MAC address, VLAN ID and the Por ...
TP-Link TL-SG3424P - page 63

50 binding-table remove Description The binding-t able remove command is used to delete the IP-MAC –VID-POR T entry from the binding table. Synt ax binding-t able remove index idx Parameter idx —— The entry number needed to be deleted. Y ou can use the show binding-t able command to get the idx. Pay attent ion to that, the entry number is the ...
TP-Link TL-SG3424P - page 64

51 Enable the DHCP-snoopi ng function globally: TP-LINK(config)# dhcp-snooping dhcp-snooping global Description The dhcp-snooping global command is used to conf igure the DHCP snooping globally . T o restore to the default value, please us e no dhcp-snooping global command. Synt ax dhcp-snooping global [ global-rate global-rate ] [ dec-threshold de ...
TP-Link TL-SG3424P - page 65

52 dhcp-snooping information enable Description The dhcp-snooping information enable command is used to enable the Option 82 function of DHCP Snooping. T o di sable the Option 82 function, please use no dhcp-snooping information enable command. Synt ax dhcp-snooping information enable no dhcp-snooping information enable Command Mode Global Configur ...
TP-Link TL-SG3424P - page 66

53 Example Replace the Option 82 field of the pa ck ets with the switch defined one and then send out: TP-LINK(config)# dhcp-snooping information strategy replace dhcp-snooping information user-defined Description The dhcp-snooping information user-defined command is used to permit users to define the Option 82. T o disable the func tion, please us ...
TP-Link TL-SG3424P - page 67

54 Example Configure the sub-option Remote ID fo r the customized Option 82 as tplink: TP-LINK(config)# dhcp-snooping information remote-id tplink dhcp-snooping information circuit-id Description The dhcp-snooping information circuit-id command is used to configure the sub-option Circuit ID for the customized Option 82. Synt ax dhcp-snooping inform ...
TP-Link TL-SG3424P - page 68

55 Configure the port 2 to be a T rusted Port: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# dhcp-snooping trusted dhcp-snooping mac-verify Description The dhcp-snooping mac-verify command is used to enable the MAC V erify feature. T o disable the MAC V erify feature, plea se use no dhcp-snooping mac-verify command. There are two fields ...
TP-Link TL-SG3424P - page 69

56 value ——The value of Flow Control. T he options are 0/ 5/10/15/20/25/30 (packet/second). The default value is 0, which stands for disable. Command Mode Interface Configuration Mode （ interface ethernet / interface range ethernet ） Example Set the Flow Control of port 2 as 20 pps: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# ...
TP-Link TL-SG3424P - page 70

57 Command Mode Any Configuration Mode Example Display the IP-MAC-VID-PORT binding table: TP-LINK(config)# show binding-t able show dhcp-snooping global Description The show dhcp-snooping global command is used to display the global configuration of DHCP Snooping. Synt ax show dhcp-snooping global Command Mode Any Configuration Mode Example Display ...
TP-Link TL-SG3424P - page 71

58 show dhcp-snooping interface Description The show dhcp-snooping interface command is used to display the interface configuration of DHCP Snooping. Synt ax show dhcp snooping interface [ eth ernet port-num ] Parameter port-num ——The number of the switch port. By default, it will display the configuration of all the ports. Command Mode Any Con ...
TP-Link TL-SG3424P - page 72

59 Chapter 12 ARP Inspection Commands ARP (Address Resolution Protocol) Detect function is to protect the switch from the ARP cheating, such as the Network Gateway S poofi ng and Man-In-The-Middle Attack, etc. arp detection (global) Description The arp detection (global) command is used to enable the ARP Detection function globally . T o disable th ...
TP-Link TL-SG3424P - page 73

60 port-list ——The specified Trusted Po rt list. Command Mode Global Configuration Mode Example Configure the ports 2-4,5-8 as the T rusted Port: TP-LINK(config)# arp detection trust-port 2-4,5-8 arp detection (interface) Description The arp detection (interface) command is us ed to enable the ARP Defend function. T o disable the arp detection ...
TP-Link TL-SG3424P - page 74

61 value. T o restore to t he default speed, please use no arp detection limit-rate command. Synt ax arp detection limit-rate value no arp detection limit-rate Parameter value ——The value to specify the maxi mum amount of the received ARP packet s per second, ranging from 10 to 100 in pps(packet/second). By default, the value is 15. Command Mod ...
TP-Link TL-SG3424P - page 75

62 show arp detection global Description The show arp detection global command is used to display the ARP detection global configuration including the enable/disable status and the T rusted Port list. Synt ax show arp detection global Command Mode Any Confiuration Mode Example Display the ARP detection configuration globally: TP-LINK(config)# show ...
TP-Link TL-SG3424P - page 76

63 The show arp detection st atistic command is used to display the number of the illegal ARP packet s received. Synt ax show arp detection st atistic Command Mode Any Configuration Mode Example Display the number of the illegal ARP packet s received: TP-LINK(config)# show arp detection statistic show arp detection statistic reset Description The s ...
TP-Link TL-SG3424P - page 77

64 Chapter 13 DoS Defend Command DoS (Denial of Service) Attack is to occupy t he network bandwid th maliciously by the network attackers or the evil programs sending a lot of se rvice requests to the Ho st. With the DoS Defend enabled, the switch can analyze the specific field of the received packet s and provide the defend measures to ensure the ...
TP-Link TL-SG3424P - page 78

65 Parameter land —— Land attack. scan-synfin —— Scan SYNFIN attack. xma-scan —— Xma Scan attack. null-scan —— NULL Scan attack. port-less-than-1024 ——The SYN packet s whose Source Port less than 1024. blat —— Blat attack. ping-flood —— Ping flooding attack, If Pi ng-flood att ack is enabled, the switch will automaticall ...
TP-Link TL-SG3424P - page 79

66 Chapter 14 IEEE 802.1X Commands IEEE 802.1X function is to provid e an access control for LAN ports via the authenticat ion. Only the supplicant passing the authenticat ion can access the LAN. dot1x Description The dot1x command is used to enable the IEEE 802.1X function globally . T o disable the IEEE 802.1X function, please use no dot1x comman ...
TP-Link TL-SG3424P - page 80

67 transmission of EAP packets is termi nated at the switch and the EAP packets are converted to the other protocol (s uch as RADIUS) packe ts for transmission EAP-MD5: IEEE 802.1X authentication system uses extensib le authentication protocol (EAP) to exchange information between the switch and the client. The EAP protocol p ackets with authentica ...
TP-Link TL-SG3424P - page 81

68 dot1x quiet-period Description The dot1x quiet-period command is used to enable t he quiet-perio d function. T o disable the f unction, please use no dot1x quiet-period command. Synt ax dot1x quiet-period no dot1x quiet-period Command Mode Global Configuration Mode Example Enable the quiet-period function: TP-LINK(config)# dot1x quiet-period dot ...
TP-Link TL-SG3424P - page 82

69 Example Configure the Quiet Period and the SupplicantTi meout as 12 seconds and 6 seconds: TP-LINK(config)# dot1x timer quiet-period 12 supp-timeout 6 dot1x retry Description The dot1x retry command is used to configure t he maximum transfer times of the repeated authentication request. T o restore to the default value, please use no dot1x retry ...
TP-Link TL-SG3424P - page 83

70 Command Mode Interface Configuration Mode （ interface ethernet / interface range ethernet ） Example Enable the IEEE 802.1X f unction for the port 1: TP-LINK(config)# interface ethernet 1 TP-LINK(config-if)# dot1x dot1x guest-vlan Description The dot1x guest-vlan command is used to enabl e the Guest VLAN function for a specified port. T o dis ...
TP-Link TL-SG3424P - page 84

71 no dot1x port-control Parameter auto | authorized-force | unauthorized-forc e —— The Control Mode for the port. Auto: In this mode, the port will normally work only after passing the 802.1X Authentication. Authorized-force: In this mode, the port can work normally without passing the 802.1X Authentication. Unauthorized-force: In this mode, t ...
TP-Link TL-SG3424P - page 85

72 Command Mode Interface Configuration Mode （ interface ethernet / interface range ethernet ） Example Configure the Control T ype for port 5 as port-based: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# dot1x port-method port-based radius authentication primary-ip Description The radius authentication primary-ip command is used to c ...
TP-Link TL-SG3424P - page 86

73 radius authentication secondary-ip ip-addr no radius authentication secondary-ip Parameter ip-addr ——The IP address of the alternate aut hentication server . By default, it is 0.0.0.0. Command Mode Global Configuration Mode Example Configure the IP address of the alter nate authentication serv er as 10.20.1.101: TP-LINK(config)# radius authe ...
TP-Link TL-SG3424P - page 87

74 The radius authentication key command is used to configure the shared password for the switch and the authen tication servers to exchange messages. T o clear the radius authent ication key , please use no radius authentication key command. Synt ax radius authentication key key-string no radius authentication key Parameter key-string ——The sh ...
TP-Link TL-SG3424P - page 88

75 radius accounting primary-ip Description The radius accounting primary-ip command is used to configure the IP address of the accounting server . Synt ax radius accounting primary-ip ip-addr Parameter ip-addr —— The IP address of the accounting server . Command Mode Global Configuration Mode Example Configure the IP address of the accounting ...
TP-Link TL-SG3424P - page 89

76 TP-LINK(config)# radius accounting secondary-ip 10.20.1.101 radius accounting port Description The radius accounting port command is used to set the UDP port of accounting server(s). T o restore to the default value, please use no radius accounting port . Synt ax radius accounting port port-num no radius accounting port Parameter port-num —— ...
TP-Link TL-SG3424P - page 90

77 Command Mode Global Configuration Mode Example Configure the shared password for the switch and the accounting servers as tplink: TP-LINK(config)# radius accounting key tplink radius response-timeout Description The radius response-timeout command is used to configure the maximum time for the switch to wait for the re sponse from the RADI US aut ...
TP-Link TL-SG3424P - page 91

78 Synt ax show dot1x global Command Mode Any configuration Mode Example Display the configuration of 801.X globally: TP-LINK(config)# show dot1x global show dot1x interface Description The show dot1x interface command is used to display the port configuration of 801.X. Synt ax show dot1x interface [ ethernet port-num ] Parameter port-num ——The ...
TP-Link TL-SG3424P - page 92

79 Any configuration Mode Example Display the configuration of the RADIUS authentic ation server: TP-LINK(config)# show radius authentication show radius accounting Description The show radius accounting command is used to display the configuration of the accounting server . Synt ax show radius accounting Command Mode Any configuration Mode Example ...
TP-Link TL-SG3424P - page 93

80 Chapter 15 Log C ommands The log information will record the settings and oper ation of the switch re spectively for you to monitor operation status and diagnose malfunction. logging local buffer Description The logging local buffer command is used to configure the severity level and the status of theconf iguration input to the log buffer . T o ...
TP-Link TL-SG3424P - page 94

81 The logging local flash command is used to configur e the l evel and the status of the log file input.T o restore to the default configur ation, please use no logging local flash command. The log file indica tes the flash sector for saving system log. The inforamtion in the log f ile will not be lost after the switch is restarted and can be got ...
TP-Link TL-SG3424P - page 95

82 Example Clear the information in the log file: TP-LINK(config)# logging clear buffer logging loghost Description The logging loghost command is used to configure the Log Host. T o clear the configuration of the specified Log Host, please use no logging loghost command. Log Host is to receive the system log from other devices. Y ou can remotely m ...
TP-Link TL-SG3424P - page 96

83 of the Local Log including t he log buffer and the log file. Synt ax show logging local-config Command Mode Any configuration Mode Example Display the configurat ion of the Local Log: TP-LINK(config)# show logging local-config show logging loghost Description The show logging loghost command is used to display the configuration of the log host. ...
TP-Link TL-SG3424P - page 97

84 Parameter leve l ——Severity level. There are 8 severity levels marked with values 0-7. The information will be displayed only when the log with the same or smaller severity level value. Display all the log information in the log buffer by default. Command Mode Any Configuration Mode Example Display the log information from level 0 to level 5 ...
TP-Link TL-SG3424P - page 98

85 Chapter 16 SSH Commands SSH (Security Shell) can prov ide the unsecured remote management with security and powerful authentication to ensure the security of the management information. ssh server enable Description The ssh server enable command is used to en able SSH function. T o disable the SSH function, please use no ssh server enable comman ...
TP-Link TL-SG3424P - page 99

86 TP-LINK(config)# ssh version v2 ssh idle-timeout Description The ssh idle-timeout command is used to specify the idle-timeout time of SSH. T o restore to the fact ory defaults, please use no ssh idle-timeout command. Synt ax ssh idle-timeout value no ssh idle-timeout Parameter value —— The Idle-timeout time. During this period, the system wi ...
TP-Link TL-SG3424P - page 100

87 S pecify the maximum number of the c onnections to the SSH server as 3: TP-LINK(config)# ssh max-client 3 ssh download Description The ssh max-client command is used to download the SSH key file from TFTP server . Synt ax ssh download { v1 | v2 } key-file ip-address ip-addr Parameter v1 | v2 —— Select the type of SSH key to download, v1 repr ...
TP-Link TL-SG3424P - page 101

88 Chapter 17 SSL Commands SSL （ Secure Sockets Layer ） , a security protocol, is to pr ovide a secure connection for the application layer protocol(e.g. H TTP) based on TCP . Adopting asymmetrical encryption tecnology , SSL uses key p air to encrypt/decrypt information. A key pair refers to a public key (cont ained in the certificate) and its ...
TP-Link TL-SG3424P - page 102

89 Command Mode Global Configuration Mode Example Download a SSL Certificate named ssl-cert from TFTP ser ver with the IP Address of 192.168.0.148: TP-LINK(config)# ssl download certificate ssl-cert ip-address 192.168.0.148 ssl download key Description The ssl download key command is used to download a SSL key to the switch from TFTP server . Synt ...
TP-Link TL-SG3424P - page 103

90 Display the global configuration of SSL: TP-LINK(config)# show ssl ...
TP-Link TL-SG3424P - page 104

91 Chapter 18 Address Commands Address configuration can improv e the network security by conf iguring the Port Security and maintaining the address information by managing the Address T able. bridge address port-security Description The bridge address port-security command is used to configure port security . T o return to the default configuratio ...
TP-Link TL-SG3424P - page 105

92 Interface Configuration Mode （ interface ethernet / interface range ethernet ） Example Enable Port Security function for port1, select S tatic mode as the learn mode, and specify the maximum number of MA C addresses that can be learned o n this port as 30: TP-LINK(config)# interface ethernet 1 TP-LINK(config-if)# bridge address port-security ...
TP-Link TL-SG3424P - page 106

93 The bridge aging-time command is used to configure aging time for the dynamic address. T o return to the default configuration, please use no bridge aging-time command. Synt ax bridge aging-time aging-time no bridge aging-time Parameter aging-time —— The aging time for the dynamic addr ess. The value of it can be 0 or ranges from 10 to 630 s ...
TP-Link TL-SG3424P - page 107

94 00:1e:4b:04:01:5d: TP-LINK(config)# bridge address filtering 00:1e:4b:04:01:5d 1 show bridge port-security Description The show bridge port-security command is used to configure the Port Security for each port, such as conf igure the Max number of MAC addressed that can be learned on the port and the Learn Mod e. Synt ax show bridge port-secur i ...
TP-Link TL-SG3424P - page 108

95 show bridge aging-time Description The show bridge aging-time command is used to display the Aging T ime of the MAC address. Synt ax show bridge aging-time Command Mode Any Configuration Mode Example Display the Aging T ime of the MAC address: TP-LINK(config)# show bridge aging-time ...
TP-Link TL-SG3424P - page 109

96 Chapter 19 System Commands System Commands can be used to configure the System informat ion and System IP , reboot and reset the switch, upgrade the swit ch system and other operations. system-descript Description The system-descript command is used to configure the Device Name, De vice Location and System Contact. T o clear all the information, ...
TP-Link TL-SG3424P - page 110

97 system-time gmt { time-zone } { ntp-server } { backup-ntp-server } no system-time gmt { time-zone } { ntp-server } { backup-ntp-server } Parameter time-zone —— Y our local time-zone, and it ranges from -12 to 13. ntp-server —— The IP Address for the Primary NTP Server . Backup-ntp-server —— The IP Address for the Secondary NTP Server ...
TP-Link TL-SG3424P - page 111

98 Synt ax system-time dst { start-date } { st art-time } {end -date } { end-time } no system-time dst Parameter start-date —— The start date of DST you set. start-time —— The start time of DST you set. end-date —— The end date of DST you set. end-time —— The end time of DST you set. Command Mode Global Configuration Mode Example Co ...
TP-Link TL-SG3424P - page 112

99 TP-LINK(config)# ip address 192.168.0.69 255.255.255.0 ip management-vlan Description The ip management-vlan command is used to conf igure the management VLAN, through which you can log on to the switch. Synt ax ip management-vlan { vlan-id } Parameter vlan-id —— VLAN ID, ranging from 1 to 4094. Command Mode Global Configuration Mode Example ...
TP-Link TL-SG3424P - page 113

100 Synt ax ip bootp-alloc Command Mode Global Configuration Mode Example Enable the BOOTP Protocol to obt ain IP address from BOOTP Server: TP-LINK(config)# ip bootp-alloc reset Description The reset command is used to reset the switch’s sof tware. After resetting, all configuration of the switch (except the IP Address) will restore to the facto ...
TP-Link TL-SG3424P - page 114

101 user-config backup Description The user-config backup command is used to backup t he configuration file by TFTP server . Synt ax user-config backup filename name ip-address ip-addr Parameter name —— S pecify the name for the config uration file which would be backuped. ip-addr —— IP Address of the TFTP server . Command Mode Privileged E ...
TP-Link TL-SG3424P - page 115

102 192.168.0.148 and name this file config.cfg: TP-LINK# user-config load filename config.cfg ip-address 192.168.0.148 user-config save Description The user-config save command is used to save current settings. Synt ax user-config save Command Mode Privileged EXEC Mode Example Save current settings: TP-LINK# user-config save firmware upgrade Descr ...
TP-Link TL-SG3424P - page 116

103 ping Description The ping command is used to test the connecti vity between the switch and one node of the network. Synt ax ping { ip_addr } [ -n { count }] [ -l { count }] [ -i { count }] Parameter ip_addr —— The IP address of the destination node for ping test. count (-n) —— The amount of times to send te st data during Ping testing. ...
TP-Link TL-SG3424P - page 117

104 Command Mode User EXEC Mode and Privileged EXEC Mode Example T est the connectivity between the switch and the network device with the IP 192.168.0.131. If t he destination device has not been found after 20 maxHops , the connection between the switch and the destination device is failed to establish: TP-LINK# tracert 192.168.0.131 20 loopback ...
TP-Link TL-SG3424P - page 118

105 Any Configuration Mode Example Display the system information: TP-LINK# show system-info show ip address Description The show ip address command is used to displa y MAC Address, IP Address, Subnet Mask and Default Gateway of t he system, whether the DHCP Client function is enabled or not and some other information. Synt ax show ip address Comma ...
TP-Link TL-SG3424P - page 119

106 show system-time dst Description The show system-time dst command is used to display the DST time information of the switch. Synt ax show system-time dst Command Mode Any Configuration Mode Example Display the DST time information of the switch TP-LINK# show system-time dst ...
TP-Link TL-SG3424P - page 120

107 Chapter 20 Ethernet Configuration Commands Ethernet Configuration Commands can be used to configure the B andwidth Control, Negotiation Mode and S torm Control for Ethernet ports. interface ethernet Description The interfac e ethernet command is used to enter t he Interface Configuration Mode and configure one Ethernet port. Synt ax interface e ...
TP-Link TL-SG3424P - page 121

108 Command in the Interface Range Ether net Mode is executed independently on all ports in the range. It does not effect the execution on the other ports at all if the command results in an error on one port. Example Enter the Interface Configuration Mode, add ports 1-3, 6-8 to the port-list and configure them: TP-LINK(config)# interface range eth ...
TP-Link TL-SG3424P - page 122

109 Interface Configuration Mode （ interface ethernet / interface range ethernet ） Example Disable Ethernet port3: TP-LINK(config)# interface ethernet 3 TP-LINK(config-if)# shut dow n flow-control Description The flow-control command is used to enable the flow -control function for a port. T o disable the flow-control function for this correspo ...
TP-Link TL-SG3424P - page 123

11 0 10h —— 10 M half-duplex. 10f —— 10M full-duplex. 100h —— 1 00M half-duplex. 100f —— 100M full-dupl ex. 1000f —— 1000M full-d uplex. Command Mode Interface Configuration Mode （ interface ethernet / interface range ethernet ） Example Configure the Negotiation Mode as 100M full-duplex for Ethern et port5: TP-LINK(config)# ...
TP-Link TL-SG3424P - page 124

111 Example Enable the S t orm Control func tion for port5 and specify the bc-rate as 128kbps, mc-rate as 512kbps and ul-rate as 2Mbp s: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# storm-control bc-rate 128k mc-rate 512k ul-rate 2m storm-control disable bc-rate Description The storm-control disable bc-rate command is used to disable t ...
TP-Link TL-SG3424P - page 125

11 2 TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# storm-control disable mc-rate storm-control disable ul-rate Description The storm-control disable ul-rate command is used to disable the UL-Frame control. Synt ax storm-control disable ul-rate Command Mode Interface Configuration Mode （ interface ethernet / interface range ethernet ? ...
TP-Link TL-SG3424P - page 126

11 3 TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# port rate-limit ingress 5120 egress 1024 port rate-limit disable ingress Description The port rate-limit disable ingress command is used to disable the ingress-rate limit. Synt ax port rate-limit disable ingress Command Mode Interface Configuration Mode （ interface ethernet / interfac ...
TP-Link TL-SG3424P - page 127

11 4 The show interface configuration command is used to display the configurations of an Ethernet port, in cluding Port-status, Flow Control, Negotiation Mode and Port-description. Synt ax show interface configuration { ethernet [ interface ] } Parameter interface —— The port selected to display the configurations. By default, the configuratio ...
TP-Link TL-SG3424P - page 128

11 5 Synt ax show interface counter s { ethernet [ interface ] } Parameter Interface —— The port selected to display the st atistic information. By default, the statistic information of all ports is displayed. Command Mode Any Configuration Mode Example Display the statistic information of Ethernet port3: TP-LINK(config)# show interface counter ...
TP-Link TL-SG3424P - page 129

11 6 port —— The port-number of the port selected to display the rate -limit information. By default, the rate-limit in formation of all port s is displayed. Command Mode Any Configuration Mode Example Display the rate-limit information of all Ethernet ports: TP-LINK(config)# show port rate-limit ...
TP-Link TL-SG3424P - page 130

11 7 Chapter 21 QoS Commands QoS (Quality of Service) f unction is used to optimiz e the netw ork performanc e. It provides yo u with network servi ce experienc e of a bett er quality . qos Description The qos command is used to configure CoS (Class of Service) based on port. T o return to the default configuration, please use no qos command. Synt ...
TP-Link TL-SG3424P - page 131

11 8 divide packet s into 8 priorities. W hen IEEE 802.1P Priority is enabled, the packet s with IEEE 802.1Q tag are mapped to different priority levels based on IEEE 802.1P priority mode. The untagged p ackets are mapped based on port priority mode. Synt ax qos dot1p config { tag } { pri } no qos dot1p config Parameter tag —— The 8 priority le ...
TP-Link TL-SG3424P - page 132

11 9 TP-LINK(config)# qos dscp enable qos dscp config Description The qos dscp config command is used to con figure the mapping relation between DSCP Priority and 802.1P Priority . T o return to the default configuration, please use no qos dscp config command. DSCP (Dif fServ Code Point) is a new definition to IP T oS field given by IEEE. This fiel ...
TP-Link TL-SG3424P - page 133

120 qos scheduler Description The qos scheduler command is used to configure the Schedule Mode. T o return to the default c onfiguration, please use no qos scheduler command. When the network is congested, the program that many packets complete for resources must be solved, usually in t he way of queue scheduling. The switch will control the forwar ...
TP-Link TL-SG3424P - page 134

121 show qos port-based Description The show qos port-based command is used to display the configuration of QoS based on port priority . Synt ax show qos port-based [ interface-nu m ] Parameter interface-num —— The Ethernet port selected to di splay the configuration. By default, information of all the ports is displayed. Command Mode Any Confi ...
TP-Link TL-SG3424P - page 135

122 show qos dscp Command Mode Any Configuration Mode Example Display the configuration of DSCP Priority: TP-LINK# show qos dscp show qos scheduler Description The show qos schedule r command is used to displa y the schedule rule of the egress queues. Synt ax show qos scheduler Command Mode Any Configuration Mode Example Display the schedule rule o ...
TP-Link TL-SG3424P - page 136

123 Chapter 22 Port Mirror Commands Port Mirror refers to the process of forwarding copies of packe ts from one port to a mirroring port. Usually , the mirroring port is connected to data diagnose device, which is used to analyze the mirrored packets for monitoring and troubleshooting the network. mirror add Description The mirror add command is us ...
TP-Link TL-SG3424P - page 137

124 same time. 3. Whether the mirroring port and mirrored ports are in the same VLAN or not is not demanded strictly . 4. The mirroring port and mirrored ports cannot be link-aggregation member . mirror remove group Description The mirror remove group command is used to remove mirror group. Synt ax mirror remove group [group- num ] Parameter group- ...
TP-Link TL-SG3424P - page 138

125 show mirror Description The show mirror command is used to display the configuration of mirror group. Synt ax show mirror [group- num ] Parameter group-num —— The group numb er of mirrior group. Command Mode Any Configuration Mode Example Display configuration fo mirror group 1: TP-LINK# show mirror 1 ...
TP-Link TL-SG3424P - page 139

126 Chapter 23 Port isolation Commands Port Isolation provides a method of restricting traffic flow to improve the network security by forbidding the port to forward packets to the por ts that are not on its forwarding port list. port isolation Description The port isolation command is used to configure the forward portlist of a port, so that this ...
TP-Link TL-SG3424P - page 140

127 Example Display the forward-list of port 6: TP-LINK# show port isolation 6 ...
TP-Link TL-SG3424P - page 141

128 Chapter 24 PoE Commands PoE (Power over Ethernet) technology describes a system to transmit electrical power along with data to remote devices over standard twisted-p air cable in an Ethernet network. It is especially useful for supplying power to IP telephones, wi reless LAN access points, cameras and so on. power inline consumption (global co ...
TP-Link TL-SG3424P - page 142

129 Command Mode Global Configuration Mode Example Configure the power disconnect method as deny-next-port: TP-LINK(config)# power inline disconnect-method deny-next-port power inline supply status Description The pow er inline supply status command is used to enable or diable the PoE feature for the corresponding port Synt ax power inline supply s ...
TP-Link TL-SG3424P - page 143

130 Interface Configuration Mode Example Enable the PoE priority as low for port 2.: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# power inline priority low power inline consumption (interface configuration) Description The power inline consumption (interface configurati on) command is used to configure the power limit the port can spup ...
TP-Link TL-SG3424P - page 144

131 name —— the time-range you ha ve configured. Command Mode Interface Configuration Mode Example Select the Seg2 as the time range for port 2.: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# power inline time-segment Seg2 power inline profile Description The pow er inline profile command is used to choose the the PoE profile you wa ...
TP-Link TL-SG3424P - page 145

132 {low|middle|high} [ consumption { power limit }] no power profile {p rofile name } Parameter profile name —— the name of the profile. supply -status —— the PoE status of the port in the profile. priority —— the PoE priority of the port in the profile. consumption —— the max power the port in the profile can supply . Command Mode ...
TP-Link TL-SG3424P - page 146

133 working day . By default, the period mode is disabled. start-date —— The start date in Absoluteness Mode, in the format of MM/DD/YYYY . By default, it is 01/01/2000. end-date —— The end date in Absoluteness Mode, in the format of MM/DD/YYYY . By default, it is 01/ 01/2000. The absoluteness mode will be disabled if the start date and end ...
TP-Link TL-SG3424P - page 147

134 Define National Day , configuring the st art date as October 1st, and the end date as October 3rd: TP-LINK(config)# power holiday NationalDay 10/01 10/03 show power inline Description The show power inline command is used to display the PoE information of the system. Synt ax show power inline Command Mode Any Configuration Mode Example Display ...
TP-Link TL-SG3424P - page 148

135 show power inline information Description The show pow er inline information command is used to display the PoE information of the certain port. Synt ax show power inline information [ ethernet port ] Parameter port —— The port selected to display the PoE information, ranging from 1 to 24. Command Mode Any Configuration Mode Example Display ...
TP-Link TL-SG3424P - page 149

136 Command Mode Any Configuration Mode Example Display the defined holiday: TP-LINK> show power holiday show power profile Description The show pow er profile command is used to display the defined PoE profile. Synt ax show power profile Command Mode Any Configuration Mode Example Display the defined PoE profile: TP-LINK> show power profile ...
TP-Link TL-SG3424P - page 150

137 Chapter 25 ACL Commands ACL (Access Control List) is used to filter data p ackets by configur ing a series of match conditions, operations and time ranges. It prov ides a flexible and secured acce ss control policy and facilitates you to control the network security . acl time-segment Description The acl time-segment command is used to add T im ...
TP-Link TL-SG3424P - page 151

138 Example Add a time-range named tSeg1, with time-s lice1 from 8:30 to 12:00 at working day: TP-LINK(config)# acl time-segment tSeg1 wee k- da y working-day time-slice1 08:30-12:00 acl edit time-segment Description The acl edit time-segment command is used to edit T ime-Range. Synt ax acl edit time-segment { na me } [ week-da y week-day ] [ st ar ...
TP-Link TL-SG3424P - page 152

139 acl holiday Description The acl holiday command is used to create holiday in Holiday Mode in the acl time-segment command. T o delete the corresponding holiday , please use no acl holiday command. Synt ax acl holiday { name } { start-date } { end-date } no acl holiday { name } Parameter name —— The holiday name, ranging from 1 to 16 charact ...
TP-Link TL-SG3424P - page 153

140 Example Create a MAC ACL whose ID is 20: TP-LINK(config)# acl create 20 acl rule mac-acl Description The acl rule mac-acl command is used to add MAC ACL rule. T o delete the corresponding rule, please use no acl rule mac-acl command. MAC ACLs analyze and process packet s based on a se ries of match conditions, which can be the source MAC addres ...
TP-Link TL-SG3424P - page 154

141 not limited. Command Mode Global Configuration Mode Example Create a MAC ACL whose ID is 20, and add Rule 10 for it. In the rule, the source MAC address is 00:01:3F:48:16:23, the source MAC address mask is 1 1:1 1:1 1:1 1:1 1:00, VLAN ID is 2, the user priority is 5, the time-range for the rule to take ef fect is tSeg1, and the packet s match t ...
TP-Link TL-SG3424P - page 155

142 ethernet-type —— EtherT yp e contained in the ru le, in the format of 4-hex number . user-pri —— The user priority contained in th e rule, ranging from 0 to 7. By default, it is not limited. time-segmen t —— The time-range for the rule to take ef fect. By default, it is not limited. index —— Change the index n umber of the entry ...
TP-Link TL-SG3424P - page 156

143 and permit means forwarding packets. By default, th e option is permit. source-ip —— The source IP address contained in the rule. source-ip-mask —— The source IP address mask. It is required if you typed the source IP address. destination-ip —— The destination IP address contained in the rule. destination-ip-mask —— The destinat ...
TP-Link TL-SG3424P - page 157

144 source-ip-mask —— The source IP address mask. It is required if you typed the source IP address. destination-ip —— The destination IP address contained in the rule. destination-ip-mask —— The destination IP address mask. It is required if you typed the destination IP address. time-segmen t —— The time-range for the rule to take ...
TP-Link TL-SG3424P - page 158

145 TP-LINK(config)# acl policy policy -add policy1 acl policy action-add Description The acl policy action-add command is used to add ACLs and create actions for the policy . T o delete the co rresponding actions, please use no acl policy action-add command. Synt ax acl policy action-add { policy-name } { acl-id } [ rate rate ] [ osd { none | disc ...
TP-Link TL-SG3424P - page 159

146 TP-LINK(config)# acl policy policy -add policy1 TP-LINK(config)# acl policy action-add policy1 120 rate 1000 osd discard acl edit action Description The acl edit action command is used to edit actions for the policy . Synt ax acl edit action { policy-name } { acl-id } [ rate rate ] [ osd {none | discard}] [ e-port egress-port ] [ vid vlan-id ] ...
TP-Link TL-SG3424P - page 160

147 bind relation, please use no acl bind to-port command. Synt ax acl bind to-port { policy-name } { port } no acl bind to-port { policy-name } { por t } Parameter policy-name —— The name of the policy desired to bind. port —— The numbe r of the port desired to bind. Command Mode Global Configuration Mode Example Bind policy1 to Port 1,3-5 ...
TP-Link TL-SG3424P - page 161

148 T ime-Range. Synt ax show acl time-segmen t Command Mode Any Configuration Mode Example Display the configuration of T ime-Range: TP-LINK> show acl time-segment show acl holiday Description The show acl holiday command is used to display the defined holiday . Synt ax show acl holiday Command Mode Any Configuration Mode Example Display the de ...
TP-Link TL-SG3424P - page 162

149 show acl bind Description The sho w acl bind command is used to display the configuration of Policy bind. Synt ax show acl bind Command Mode Any Configuration Mode Example Display the configuration of Policy bind: TP-LINK> show acl bind ...
TP-Link TL-SG3424P - page 163

150 Chapter 26 MSTP Commands MSTP (Multiple S panning T ree Protocol), comp at ible with both STP and RSTP and subject to IEEE 802.1s, can disbranch a ri ng network. STP is to block redundant links and backup links as well as optimize paths. spanning-tree global Description The sp anning-tree global command is used to configure STP globally . T o r ...
TP-Link TL-SG3424P - page 164

151 hold-count —— TxHold Count, which is the maximum number of BP DU packet s transmitted per Hello T ime interv al. TxHold Count ranges from 1 to 2 0 in pps. By default, it is 5. max-hops —— Max Hop s, which is the maximum number of hops that occur in a specific region before t he BPDU is discarded. Max Hops ranges from 1 to 40 in hop. By ...
TP-Link TL-SG3424P - page 165

152 port. The lower value has the higher priority . expath-consum —— ExtPath Cost, which is us ed to choose the p ath and calculate the path cost s of ports in different MST regions. It is an important criterion on determining the root port. The lower value has the higher priority . By default, it is automatic. inpaht-consum —— IntPath Cost ...
TP-Link TL-SG3424P - page 166

153 name —— The region name, used to identify MST region. It ranges from 1 to 32 characters. revision —— The revision for MST region identification, ranging from 0 to 65535. Command Mode Global Configuration Mode Example Configure the region name of MSTP as r1, and the revision level as 100: TP-LINK(config)# spanning-tree region r1 100 span ...
TP-Link TL-SG3424P - page 167

154 Enable Instance 1, add VLAN 2, 3, 4, 5, 8 for it, and configure MSTI Priority as 4096: TP-LINK(config)# spanning-tree msti 1 st atus enable pri 4096 mapped 2-5,8 spanning-tree msti Description The sp anning-tree msti command is used to configure MSTP Instance Port. T o return to the default conf iguration of the corresponding Instance Port, ple ...
TP-Link TL-SG3424P - page 168

155 S panning T ree globally . T o return to t he default configurat ion, please use no sp anning-tree tc-defen d command. A switch removes MAC address entries upon receiving TC-BPDUs. If a malicious user continuously sends TC-BPDUs to a switch, the switch will be busy with removing MAC address entries, which may decrease the performance and stabil ...
TP-Link TL-SG3424P - page 169

156 is to prevent wrong network topology change caused by the role change of the current legal root bridge. TC —— Enable/ Disable TC Protect. By default, it is disabled. defend —— Enable/ Disable BPDU Protect. By default, it is disabled. BPDU Protect is to prevent the edge port fr om being attacked by maliciously created BPDUs. hold —— ...
TP-Link TL-SG3424P - page 170

157 Synt ax show spanning-tree global-info Command Mode Any Configuration Mode Example Display the current st atus of S panning T ree: TP-LINK# show spanning-tree global-info show spanning-tree global-config Description The show spanning-tree global-config command is used to display the global configuration of S panning T ree. Synt ax show spanning ...
TP-Link TL-SG3424P - page 171

158 Display the configuration of port 5: TP-LINK(config)# show spanning-tree port-config 5 show spanning-tree region Description The show spanning-tree region command is used to display the Region configuration of MSTP . Synt ax show spanning-tree region Command Mode Any Configuration Mode Example Display the region configuration of MSTP: TP-LINK(c ...
TP-Link TL-SG3424P - page 172

159 The show spanning-tree msti port command is used to display the Instance Port configuration of S pan ning T ree. Synt ax show spanning-tree msti port { id } [ port ] Parameter id —— Instance ID, ranging from 1 to 8. port —— The port selected to display t he configuration. By default, the configuration of all ports is displayed. Command ...
TP-Link TL-SG3424P - page 173

160 port —— The port selected to display the configuration. By default, the Port Protect configuration of all ports is displayed. Command Mode Any Configuration Mode Example Display the Port Protect configuration of port 2: TP-LINK(config)# show spanning-tree security port-defend 2 ...
TP-Link TL-SG3424P - page 174

161 Chapter 27 IGMP Commands IGMP Snooping (Internet Group Management Prot ocol Snooping) is a multicast control mechanism running on Layer 2 switch. It can effectively prevent multicast groups being broadcasted in the network. igmp-snooping global Description The igmp-snooping global command is used to configure IGMP globally . T o return to the d ...
TP-Link TL-SG3424P - page 175

162 Synt ax igmp-snooping config st atus {disable | enable} fast-leave {di sable | enable} no igmp-snooping config Parameter status —— Enable/ Disable IGMP Snooping for the desired port. fast-leave —— Enable/ Disable Fast Leave feat u re for the desired port. If Fast Leave is enabled for a port, the switch will immediately remove this port ...
TP-Link TL-SG3424P - page 176

163 member-time —— Member Port T ime. Within this time, if the switch does not receive IGMP report message from the member port, it will consider this port is not a member port any more. Member Port Time ranges from 60 to 600 in seconds. By default, it is 260. leave-time —— Leave Time, which is the interval between the switch reveiving a le ...
TP-Link TL-SG3424P - page 177

164 receive IGMP report message from the member port, it will consider this port is not a member port any more. Member Port Time ranges from 60 to 600 in seconds. By default, it is 260. leave-time —— Leave Time, which is the interval between the switch reveiving a leave message from a host and the switch removing the host from the multicast gro ...
TP-Link TL-SG3424P - page 178

165 seconds. By default, it is 260. leave-time —— Leave Time, which is the interval between the switch reveiving a leave message from a host and the switch removing the host from the multicast groups. Leave T ime ranges from 1 to 30 in seconds. By default, it is 1. router-port —— S tatic Router Port, which is mainly used in the netwo rk wit ...
TP-Link TL-SG3424P - page 179

166 configure the forward port as port 1: TP-LINK(config)# igmp-snooping st atic-entry-add 225.0.0.1 2 1 igmp-snooping filter-add Description The igmp-snooping filter-add command is used to c onfigure the multicast IP-range desired to filter . T o delete th e corresponding IP-range, please use no igmp-snooping filter-add command. When IGMP Snooping ...
TP-Link TL-SG3424P - page 180

167 id —— IP-range ID, ranging from 1 to 30. start-ip —— The start multicast IP of the IP-range. end-ip —— The end multicast IP of the IP-range. Command Mode Global Configuration Mode Example Modify the multicast IP-range whose ID is 20 as 225.0. 0.10~225.0.0.12: TP-LINK(config)# igmp-snooping filter-config 20 225.0.0.10 225.0.0.12 igmp ...
TP-Link TL-SG3424P - page 181

168 Interface Configuration Mode （ interface ethernet / interface range ethernet ） Example Enable multicast filtering function for port 5, specif y Action Mode as accept, bound IP-range 2, 3, 4, and specify the maximum number of multicast groups for port 5 to join in as 128: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# igmp-snoopin ...
TP-Link TL-SG3424P - page 182

169 Example Display the IGMP configuration of port 2: TP-LINK> show igmp-snooping port-config 2 show igmp-snooping vlan-config Description The show igmp-snooping vlan-config command is used to display the VLAN configuration of IGMP . Synt ax show igmp-snooping vlan-config Command Mode Any Configuration Mode Example Display the VLAN configuration ...
TP-Link TL-SG3424P - page 183

170 Synt ax show igmp-snooping multi-ip-list Command Mode Any Configuration Mode Example Display the Multicast IP t able: TP-LINK> show igmp-snooping multi-ip-list show igmp-snooping filter-ip-addr Description The show igmp-snooping filter-ip-addr command is used to display the Multicast Filter IP-Range table. Synt ax show igmp-snooping filter-i ...
TP-Link TL-SG3424P - page 184

171 TP-LINK> show igmp-snooping port-filter 5 show igmp-snooping packet-stat Description The show igmp-snooping packet-st at command is used to display the Packet S tatistics information of all ports. Synt ax show igmp-snooping p acket-st at Command Mode Any Configuration Mode Example Display the Packet S tatistics information: TP-LINK> show ...
TP-Link TL-SG3424P - page 185

172 Chapter 28 SNMP Commands SNMP (Simple Network Management Protocol) func tions are used to manage the network devices for a smooth communication, whic h can facilitate the network administrators to monitor the network nodes and implement the proper operation. snmp global Description The snmp global command is used to configure the SNMP function ...
TP-Link TL-SG3424P - page 186

173 snmp view-add Description The snmp view-add command is used to add View . T o delete the corresponding View , please use no snmp view -add command. The OID (Object Identifier) of the SNMP p ackets is used to describe the managed objects of the switch, and the MIB (Management In formation Base) is the set of the OIDs. The SNMP V iew is created f ...
TP-Link TL-SG3424P - page 187

174 privacy mode guarantee the high securi ty for the communication between the management station and the managed device. Synt ax snmp group-add { name } [ smode { v1 | v2c | v3 }] [ slev { noAuthNoPriv | authNoPriv | authPriv }] [ ro ro-view ] [ wo wo-view ] [ notify notify-view ] no snmp group-add { name } { smode { v1 | v2c | v3 }} { slev { noA ...
TP-Link TL-SG3424P - page 188

175 snmp user-add Description The snmp user-add command is used to add User . T o delete the corresponding User , plea se use no snmp user-add command. The User in a SNMP Group can manage the switch via the management station sof tware. The User and its Group have the same security level and access right. Synt ax snmp user-add { name } { local | re ...
TP-Link TL-SG3424P - page 189

176 encryption method is used. By def ault, the Privacy Mode is none. encrypt-pwd —— Privacy Password, rangin g from 1 to 16 characters. Command Mode Global Configuration Mode Example Add User admin to Group group2, and configure the Security Model of the user as v3, the Security Level of the group as authPriv , the Authentication Mode of the u ...
TP-Link TL-SG3424P - page 190

177 snmp notify-add Description The snmp notify -add command is used to add Notification. T o delete the corresponding Notification, please use no snmp notify-add command. With the Notification function enabled, the switch can initiatively report to the management station about the importa nt ev ents that occur on the Views, which allows the manage ...
TP-Link TL-SG3424P - page 191

178 Command Mode Global Configuration Mode Example Add a Notification entry , and configure t he IP Address o f the management Host as 192.168.0.1, the UDP port as 162, the User name of the management st ation as admin, the Security Model of the manag ement station as v2c, the type of the notifications as inform, the maximum ti me for the switch to ...
TP-Link TL-SG3424P - page 192

179 TP-LINK(config)# snmp-rmon history sample-cfg 1-3 1 100 snmp-rmon history owner Description The snmp-rmon history o wner command is used to conf igure the owner of the history sample entry . T o return to the default configur ation, please use no snmp-rmon history owner command. Synt ax snmp-rmon history owner { index } [ owner ] no snmp-rmon h ...
TP-Link TL-SG3424P - page 193

180 Global Configuration Mode Example Enable the history sample entries 1,2,3,4 and 8: TP-LINK(config)# snmp-rmon history enable 1-4,8 snmp-rmon event user Description The snmp-rmon event user command is used to conf igure the user name of SNMP-RMON Event. T o return to t he default configurat ion, please use no snmp-rmon event user command. Event ...
TP-Link TL-SG3424P - page 194

181 no snmp-rmon event description { index } Parameter index —— The index number of the event e n try , ranging from 1 to 12. Y ou can only select one entry for each command. description —— The description of the eve nt, ranging from 1 to 16 characters. By default, it is empty . Command Mode Global Configuration Mode Example Configure the d ...
TP-Link TL-SG3424P - page 195

182 snmp-rmon event owner Description The snmp-rmon event owner command is used to configure the owner of SNMP-RMON Event. T o return to t he default configurat ion, please use no snmp-rmon event owner command. Synt ax snmp-rmon event owner { index } [ owner ] no snmp-rmon event owner { index } Parameter index —— The index number of the event e ...
TP-Link TL-SG3424P - page 196

183 Enable the SNMP-RMON Event entries 1,2,3,4 and 8: TP-LINK(config)# snmp-rmon event enable 1-4,8 snmp-rmon alarm config Description The snmp-rmon alarm config command is used to configure SNMP-RMON Alarm Management. T o return to the default configuration, please use no snmp-rmon alarm config command. Alarm Group is one of the commonly used RMON ...
TP-Link TL-SG3424P - page 197

184 f-hold —— The falling counter value that tr iggers the Falling Threshold alarm, ranging from 1 to 65535. By default, it is 100. f-event —— Fall Event, which is the index of the corresponding event which will be triggered if the sampled value is lower than the Falling Threshold. It ranges from 1 to 12. a-type —— Alarm T ype, with ris ...
TP-Link TL-SG3424P - page 198

185 Configure the owner of entry 1 as owner1: TP-LINK(config)# snmp-rmon alarm owner 1 owner1 snmp-rmon alarm enable Description The snmp-rmon alarm enable command is used to enable SNMP-RMON Alarm Management entry . T o disable the corresponding ent ry , please use no snmp-rmon alarm enable command. Synt ax snmp-rmon alarm enable { index } no snmp ...
TP-Link TL-SG3424P - page 199

186 show snmp view Description The show snmp view command is used to display the View ta ble. Synt ax show snmp view Command Mode Any Configuration Mode Example Display the View table: TP-LINK> show snmp view show snmp group Description The show snmp group command is used to display the Group table. Synt ax show snmp group Command Mode Any Confi ...
TP-Link TL-SG3424P - page 200

187 TP-LINK> show snmp user show snmp community Description The sho w snmp community command is used to displa y the Community table. Synt ax show snmp community Command Mode Any Configuration Mode Example Display the Community table: TP-LINK> show snmp community show snmp destination-host Description The show snmp destination-host command is ...
TP-Link TL-SG3424P - page 201

188 index —— The index nu mber of the entry sele cted to display the configuration, ranging from 1 to 12. Y ou can only select one entry for each command. By default, the configuration of all entries is displayed. Command Mode Any Configuration Mode Example Display the configuration of all history sample entries: TP-LINK> show snmp-rmon hist ...
TP-Link TL-SG3424P - page 202

189 ranging from 1 to 12. Y ou can only select one entry for each command. By default, the configuration of all entries is displayed. Command Mode Any Configuration Mode Example Display the configuration of all Alarm Management entries: TP-LINK> show snmp-rmon alarm ...
TP-Link TL-SG3424P - page 203

190 Chapter 29 LLDP Commands LLDP function enables network devic es to advertise their own device information periodically to neighbors on the same LAN. The information of the LLDP devices in the LAN can be stored by its neighbor in a standard MIB, so it is possible fo r the information to be accessed by a Network Management System (NMS) using SNMP ...
TP-Link TL-SG3424P - page 204

191 Command Mode Global Configuration Mode Example S pecify Hold Multiplier as 5: TP-LINK(config)# lld p hold-multiplier 5 lldp timer Description The lldp timer command is used to confi gure the parameters about transmission. T o return to the default configurat ion, please use no lldp timer command. Synt ax lld p timer tx-interval tx-interval lld ...
TP-Link TL-SG3424P - page 205

192 Rx_Only) to Tx&Rx (or Tx_Only), the fa st start mechanism will be enabled, that is, the transmit interval will be short en to a second, and several LLDPDUs will be sent out (the number of LLDPDUs equal s this parameter). The default value is 3. Command Mode Global Configuration Mode Example S pecify the T ransmit Interval of LLD PDU as 45 s ...
TP-Link TL-SG3424P - page 206

193 The lld p admin-st atus command is used to configur e the port’s LLDP operat ing mode. T o return to the defaul t configurati on, please use no lldp admin-status command. Synt ax lld p admin-st atus {disa ble | tx | rx | txrx } no lld p admin-st atus Parameter disable —— Neither transmit nor receive LLDP frames. tx —— Only transmit LL ...
TP-Link TL-SG3424P - page 207

194 lldp tlv-select Description The lld p tlv-select command is used to configure TL Vs to be included in outgoing LLDPDU. T o ex clude TL Vs, please use no lld p tlv-select command. By default, All TL Vs are included in outgoing LLDPDU. Synt ax lld p tlv-select [port-description] [system-cap ability] [system-description] [system-name] [management- ...
TP-Link TL-SG3424P - page 208

195 Interface Configuration Mode （ interface ethernet / interface range ethernet ） Example Enable the LLDP-MED status for port 6: TP-LINK(config)# interface ethernet 6 TP-LINK(config-if)# lldp med-status enable lldp med-tlv-select Description The lldp med-tlv-select command is used to configure TL Vs to be included in outgoing LLDPDU. T o ex cl ...
TP-Link TL-SG3424P - page 209

196 Parameter emergency-number —— Emergency number is Emergency Call Service ELIN identifier, which is used during emergency call setup to a traditional CAMA or ISDN trunk-based PSAP. civic-address —— The Civic address is defined to reuse the relevant sub-fields of the DHCP option for Civic Address bas ed Location Config uration Information ...
TP-Link TL-SG3424P - page 210

197 Synt ax show lldp interface [ ethernet port ] Parameter port —— The port selected to displa y the c onfiguration of LLDP , ranging from 1 to 24. Command Mode Any Configuration Mode Example Display the LLDP conf iguration of port 8: TP-LINK> show lldp int erface ethernet 8 show lldp local-information Description The show lldp local-inform ...
TP-Link TL-SG3424P - page 211

198 port —— The port selected to display the neighbor information, ranging from 1 to 24. Command Mode Any Configuration Mode Example Display the neighbor information of port 8: TP-LINK> show lldp neighbor-information 8 show lldp statistics Description The show lldp st atistics command is used to display the LLDP statistic information between ...
TP-Link TL-SG3424P - page 212

199 TP-LINK> show lldp med fast-count show lldp med interface Description The show lldp med interface command is used to display LLDP-MED configuration of the certain port. Synt ax show lldp med interface [ ethernet port ] Parameter port —— The port selected to displa y the c onfiguration of LLDP , ranging from 1 to 24. Command Mode Any Conf ...
TP-Link TL-SG3424P - page 213

200 show lldp med neighbor-information Description The show lld p med neighbor-information command is used to display the neighbor ’s LLDP-MED information of the certain port. Synt ax show lldp med neighbor-information [ port ] Parameter port —— The port selected to display the neighbor information, ranging from 1 to 24. Command Mode Any Conf ...
TP-Link TL-SG3424P - page 214

201 Chapter 30 Cluster Commands Cluster Management function enables a network administrator to manage the scattered devices in the network via a manag ement device. After a co mm ander switc h is configured, management and maintenance operations intended fo r the member devices in a cl uster is implemented by the commander device. cluster ndp Descr ...
TP-Link TL-SG3424P - page 215

202 cluster ntdp Description The cluster ntd p command is used to configure NTDP globally . T o return to the default configuration, please use no cluster nt dp command. NTDP (Neighbor T opology Discovery Protocol) is used to collect the NDP information and neighboring connection information of each device in a specif ic network range. It provides ...
TP-Link TL-SG3424P - page 216

203 TP-LINK(config)# cluster ntd p status enable interval 20 hop 5 hop-delay 300 port-delay 50 cluster explore Description The cluster explore command is used to enable the topology information collecting function manually . Synt ax cluster explore Command Mode Global Configuration Mode Example Enable the topology informati on collecting function m ...
TP-Link TL-SG3424P - page 217

204 cluster manage role-change Description The cluster manage role-change command is used to change the role of the current switch. According to their status and functions, switc hes in the cluster play different roles. Y ou c an specify the role the switch plays appropriate to your needs. A commander s witch can recogni ze and manage the devices i ...
TP-Link TL-SG3424P - page 218

205 show cluster ndp port-status Description The show cluster nd p port-st atus command is used to display NDP configuration of the certain port. Synt ax show cluster ndp port-st atus [ port ] Parameter port —— The port selected to display the c onfiguration of NDP . By default, the configuration of all ports is displayed. Command Mode Any Conf ...
TP-Link TL-SG3424P - page 219

206 show cluster nt dp global Command Mode Any Configuration Mode Example Display the global configuration of NTDP: TP-LINK> show cluster nt dp global show cluster ntdp port-status Description The show cluster nt dp port-st atus command is used to display NTDP configuration of the certain port. Synt ax show cluster ntd p port-status [ port ] Par ...
TP-Link TL-SG3424P - page 220

207 TP-LINK> show cluster nt dp device show cluster manage role Description The show cluster manage role command is used to display the role of the current switch. Synt ax show cluster manage role Command Mode Any Configuration Mode Example Display the role of the current switch: TP-LINK> show cluster manage role ...

Fabbricante TP-Link Categoria Switch

I documenti che otteniamo dal fabbricante del dispositivoTP-Link TL-SG3424P possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici TP-Link
- manuali per l’uso TL-SG3424P
- schede prodotto TP-Link
- opuscoli
- o etichette energetiche TP-Link TL-SG3424P
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso TP-Link TL-SG3424P.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione TP-Link TL-SG3424P, manuali di manutenzione, brevi manuali o manuali utente TP-Link TL-SG3424P. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto TP-Link TL-SG3424P.

Manuali per l’uso simili

TP-Link TL-SL2428WEB/TL-SL2452WEB

64 pagine
TP-Link TL-SF1048

24 pagine
TP-Link TL-SL1226

12 pagine
TP-Link Tl-SB2216

32 pagine

Manuale completo del dispositivo TP-Link TL-SG3424P, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare TP-Link TL-SG3424P dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti TP-Link TL-SG3424P.

Il manuale per l’uso completo TP-Link, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale TP-Link TL-SG3424P - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice TP-Link TL-SG3424P, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per TP-Link TL-SG3424P che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo TP-Link TL-SG3424P - che ci dovrebbe aiutare nei primi passi durante l'uso TP-Link TL-SG3424P
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del TP-Link TL-SG3424P
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio TP-Link TL-SG3424P in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su TP-Link TL-SG3424P?

Utilizza il modulo sottostante

Se non hai risolto il problema con TP-Link TL-SG3424P con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con TP-Link TL-SG3424P è probabile che voglia condividere il modo di risolverlo.

Manuale per l’uso TP-Link TL-SG3424P

Summary

TP-Link TL-SG3424P - page 1

TP-Link TL-SG3424P - page 2

TP-Link TL-SG3424P - page 3

TP-Link TL-SG3424P - page 4

TP-Link TL-SG3424P - page 5

TP-Link TL-SG3424P - page 6

TP-Link TL-SG3424P - page 7

TP-Link TL-SG3424P - page 8

TP-Link TL-SG3424P - page 9

TP-Link TL-SG3424P - page 10

TP-Link TL-SG3424P - page 11

TP-Link TL-SG3424P - page 12

TP-Link TL-SG3424P - page 13

TP-Link TL-SG3424P - page 14

TP-Link TL-SG3424P - page 15

TP-Link TL-SG3424P - page 16

TP-Link TL-SG3424P - page 17

TP-Link TL-SG3424P - page 18

TP-Link TL-SG3424P - page 19

TP-Link TL-SG3424P - page 20

TP-Link TL-SG3424P - page 21

TP-Link TL-SG3424P - page 22

TP-Link TL-SG3424P - page 23

TP-Link TL-SG3424P - page 24

TP-Link TL-SG3424P - page 25

TP-Link TL-SG3424P - page 26

TP-Link TL-SG3424P - page 27

TP-Link TL-SG3424P - page 28

TP-Link TL-SG3424P - page 29

TP-Link TL-SG3424P - page 30

TP-Link TL-SG3424P - page 31

TP-Link TL-SG3424P - page 32

TP-Link TL-SG3424P - page 33

TP-Link TL-SG3424P - page 34

TP-Link TL-SG3424P - page 35

TP-Link TL-SG3424P - page 36

TP-Link TL-SG3424P - page 37

TP-Link TL-SG3424P - page 38

TP-Link TL-SG3424P - page 39

TP-Link TL-SG3424P - page 40

TP-Link TL-SG3424P - page 41

TP-Link TL-SG3424P - page 42

TP-Link TL-SG3424P - page 43

TP-Link TL-SG3424P - page 44

TP-Link TL-SG3424P - page 45

TP-Link TL-SG3424P - page 46

TP-Link TL-SG3424P - page 47

TP-Link TL-SG3424P - page 48

TP-Link TL-SG3424P - page 49

TP-Link TL-SG3424P - page 50

TP-Link TL-SG3424P - page 51

TP-Link TL-SG3424P - page 52

TP-Link TL-SG3424P - page 53

TP-Link TL-SG3424P - page 54

TP-Link TL-SG3424P - page 55

TP-Link TL-SG3424P - page 56

TP-Link TL-SG3424P - page 57

TP-Link TL-SG3424P - page 58

TP-Link TL-SG3424P - page 59

TP-Link TL-SG3424P - page 60

TP-Link TL-SG3424P - page 61

TP-Link TL-SG3424P - page 62

TP-Link TL-SG3424P - page 63

TP-Link TL-SG3424P - page 64

TP-Link TL-SG3424P - page 65

TP-Link TL-SG3424P - page 66

TP-Link TL-SG3424P - page 67

TP-Link TL-SG3424P - page 68

TP-Link TL-SG3424P - page 69

TP-Link TL-SG3424P - page 70

TP-Link TL-SG3424P - page 71

TP-Link TL-SG3424P - page 72

TP-Link TL-SG3424P - page 73

TP-Link TL-SG3424P - page 74

TP-Link TL-SG3424P - page 75

TP-Link TL-SG3424P - page 76

TP-Link TL-SG3424P - page 77

TP-Link TL-SG3424P - page 78