Italiano dropdown-ico

Manuale per l’uso Miele 371 G

32 pagine 1.01 mb
Scarica

Vai alla pagina of 32

Summary
  • Miele 371 G - page 1

    Installation instructions Gas hobs K M3 7 0G/K M 370-1 G KM 371 G K M3 9 0G/K M3 9 1G To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 05 827 720 e n-G B ...

  • Miele 371 G - page 2

    G This appliance can be used in countries other than those specified on the appliance. It is, however, set up for connection to the gas and electricity supplies in the countries specified. For use in other countries please contact the Miele spare parts or customer service department in your country. D Das Gerät ist auch für den Gebrauch in andere ...

  • Miele 371 G - page 3

    Gas-heated appliances Safety precautions to take if you smell gas ß Turn off the gas emergency control valve immediately. This is usually located near the gas meter. ß Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches. ß Do not operate electrical lights or switches, i.e. do not switch them &quo ...

  • Miele 371 G - page 4

    Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Appliance dimensions and worktop cut-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 K M3 7 0 ...........................................................7 KM 370-1 G .................................................. ...

  • Miele 371 G - page 5

    Building in Fit wall units and extractor hood before fitting the hob, to avoid damaging the appliance. ~ The veneer or laminate coating of worktops (or adjacent kitchen units) must be treated with 100 °C heat-resistant adhesive which will not dissolve or distort. Any backmoulds must be of heat-resistant material. ~ Ideally the gas hob should be in ...

  • Miele 371 G - page 6

    ~ The room in which the gas hob is installed must be at least 20 m 3 in size with a door or window in it which can be opened to the outside air. ~ Using the gas hob will cause a build-up of heat and moisture in the room in which it is installed. Ensure that the room has sufficient natural or mechanical means of ventilation, e.g. an extractor. ~ If ...

  • Miele 371 G - page 7

    KM 370 a Building-in depth b Mains connection box c Gas connection R 1 / 2 - ISO 7-1 (DIN2999) Appliance dimensions and worktop cut-out 7 ...

  • Miele 371 G - page 8

    KM 370-1 G a Building-in depth b Mains connection box c Gas connection R 1 / 2 - ISO 7-1 (DIN2999) Appliance dimensions and worktop cut-out 8 ...

  • Miele 371 G - page 9

    KM 371 a Building-in depth b Mains connection box c Gas connection R 1 / 2 - ISO 7-1 (DIN2999) Appliance dimensions and worktop cut-out 9 ...

  • Miele 371 G - page 10

    KM 390 a Building-in depth b Mains connection box c Gas connection R 1 / 2 - ISO 7-1 (DIN2999) Appliance dimensions and worktop cut-out 10 ...

  • Miele 371 G - page 11

    KM 391 a Building-in depth b Mains connection box c Gas connection R 1 / 2 - ISO 7-1 (DIN2999) Appliance dimensions and worktop cut-out 11 ...

  • Miele 371 G - page 12

    ^ Prepare the worktop cut-out as shown in the diagram. Remember to maintain a minimum safety distance of 50 mm between the hob and the back wall and 150 mm between it and a side wall or tall unit to the right or left of the hob. (See "Warning and Safety instructions"). ^ Seal the cut surfaces with a suitable heat-resistant sealant to avoi ...

  • Miele 371 G - page 13

    Building in the appliance ^ Feed the electricity connection cable through the cut-out and connect. ^ Place the gas hob in the prepared cut-out. ^ Make the gas connection (see relevant section). Securing the appliance KM 371 G / KM 391 G ^ Secure the gas hob at the front and rear with fixing brackets a supplied as shown. KM 370 G / KM 370-1 G / KM 3 ...

  • Miele 371 G - page 14

    Do not let sealant get in between the hob frame and the worktop. This could cause difficulties if the hob ever needs to be taken out for servicing and possibly result in damage to the hob frame or the worktop. The sealing strip under the edge of the top part of the hob provides a sufficient seal for the worktop. Installation 14 ...

  • Miele 371 G - page 15

    All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current local and national safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. Ensure power is not supplie ...

  • Miele 371 G - page 16

    Important The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system, which complies with current local and national safety regulations. It is most important that this basic safety requirement is present and regularly tested and where there is any doubt, the electrical wiri ...

  • Miele 371 G - page 17

    Connection to the gas supply, or conversion from one type of gas to another should only be undertaken by an approved and registered gas installer in strict accordance with local and national safety and building regulations, (e.g. Corgi registered in the U.K.) Every appliance should have its own isolating valve and test point. Check with your local ...

  • Miele 371 G - page 18

    a Connection with test point specifically for GB b Connection with test point specifically for GB and 90° angle Natural gas / liquid gas ^ The appliance is supplied with an R 1/2" - ISO 7-1 (DIN 2999) gas connection point. ^ An appropriate rigid connection and isolating valve must be installed for final connection. ^ The gas connection must b ...

  • Miele 371 G - page 19

    Nominal rating for all gas types with the burner full on Burner Gas type KM 370 G / KM 370-1 G / KM 371 G KM 390 G / KM 391 G kW g/h kW g/h Small burner Natural gas H Liquid gas 1.00 1.00 - 73 1.00 1.00 - 73 Normal burner Natural gas H Liquid gas 1.75 1.75 - 127 1.75 1.75 - 127 Large burner Natural gas H Liquid gas 3.00 3.00 - 218 3.00 3.00 - 218 W ...

  • Miele 371 G - page 20

    KM 370 G / KM 370-1 G / KM 371 G When converting to anothe type of gas, the main jets and the small jets on all burners have to be changed. Screw in the new jets according to the following table. For U.K. and IE Main jet Ø Small jet Ø Natural gas H Small burner Medium burner Large burner Wok 0.76 1.00 1.29 1.29 / 0.63 0.39 0.42 0.54 0.80 Liquid g ...

  • Miele 371 G - page 21

    Changing the jets Disconnect the gas hob from the electricity supply by switching off at the socket and withdrawing the plug or by removing the mains fuse. Changing the main jets Small, medium and large burners ^ Take off the pan support, burner cap b and the burner head d . ^ Using an M7 socket spanner unscrew the main jet e . ^ Change the main je ...

  • Miele 371 G - page 22

    Wok burner ^ Take off the burner cap a , burner ring b and burner head c . ^ Loosen screws d and remove the cover plate. ^ Using an M7 socket spanner unscrew the main jets e (larger diameter jet) and f (smaller diameter jet). ^ Change the main jets. Conversion to another type of gas 22 ...

  • Miele 371 G - page 23

    Changing the small jets (for all burners) To change the small jets, the burner securing screws must first be loosened and the upper section of the appliance removed. ^ Remove the operating controls by pulling them upwards. ^ Remove the upper section. N.B. To remove a ceramic upper section: Insert the lever supplied between the frame and the worktop ...

  • Miele 371 G - page 24

    After changing the jets ^ Assemble the removed burner parts in reverse order and check for leaks by operating the burner without the upper section of the hob in place (use a match to ignite the flame). ^ Remove the burner parts again. ^ Then replace the upper section of the hob. ^ Screw in the burner bases and re-assemble the burner parts, making s ...

  • Miele 371 G - page 25

    KM 390 G / KM 391 G When converting to another type of gas, the main jets and the small jets on all burner have to be changed. Screw in the new jets according to the following table. For U.K. and IE Main jet Ø Small jet Ø Natural gas H Small burner Medium burner Large burner Wok 0.76 1.00 1.29 1.40 / 0.68 0.39 0.42 0.54 0.88 / 0.42 Liquid gas Sma ...

  • Miele 371 G - page 26

    Changing the jets Disconnect the gas hob from the electricity supply by switching off at the socket and withdrawing the plug or by removing the mains fuse. Changing the main jets Small, medium and large burners ^ Take off the pan support, burner cap b and the burner head d . ^ Using an M7 socket spanner unscrew the main jet e . ^ Change the main je ...

  • Miele 371 G - page 27

    Wok burner ^ Take off the burner cap a , burner ring b and the burner head c . ^ Loosen screws d and remove the cover plate. ^ Using an M7 socket spanner unscrew the main jets e (larger diameter) and f (smaller diameter). ^ Change the main jets. Conversion to another type of gas 27 ...

  • Miele 371 G - page 28

    Changing the small jets To change the small jets, the burner securing screws must first be loosened and the upper section of the appliance removed. ^ Remove the operating controls by pulling them upwards. ^ Remove the upper section. N.B. To remove a ceramic upper section: Insert the lever supplied between the frame and the worktop, prise up the upp ...

  • Miele 371 G - page 29

    Wok burner b Small jet with smaller diameter (e.g. for liquid gas: 0.20). c Small jet with larger diameter (e.g. for liquid gas: 0.46). ^ Remove the ignitor a . ^ Using a small screwdriver, unscrew the small jets b and c in the gas fitting. ^ Pull the jets out with a pair of pointed pliers. ^ Select the jets as shown in the table, fit, reversing th ...

  • Miele 371 G - page 30

    After changing the jets ^ Assemble the removed burner parts in reverse order and check for leaks by operating the burner without the upper section of the hob in place (use a match to ignite the flame). ^ Remove the burner parts again. ^ Then replace the upper section of the hob. ^ Screw in the burner bases and re-assemble the burner parts, making s ...

  • Miele 371 G - page 31

    31 ...

  • Miele 371 G - page 32

    Alteration rights reserved / 3209 M.-Nr. 05 827 720 / 10 ...

Fabbricante Miele Categoria Cooktop

I documenti che otteniamo dal fabbricante del dispositivoMiele 371 G possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Miele
- manuali per l’uso 371 G
- schede prodotto Miele
- opuscoli
- o etichette energetiche Miele 371 G
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Miele 371 G.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Miele 371 G, manuali di manutenzione, brevi manuali o manuali utente Miele 371 G. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Miele 371 G.

Manuali per l’uso simili

Manuale completo del dispositivo Miele 371 G, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Miele 371 G dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Miele 371 G.

Il manuale per l’uso completo Miele, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Miele 371 G - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Miele 371 G, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Miele 371 G che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Miele 371 G - che ci dovrebbe aiutare nei primi passi durante l'uso Miele 371 G
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Miele 371 G
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Miele 371 G in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Miele 371 G?

Utilizza il modulo sottostante

Se non hai risolto il problema con Miele 371 G con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Miele 371 G è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)