-
Bell'O 8210DB - page 1
...
-
Bell'O 8210DB - page 2
Icons Used in This Book Don’t be alarmed by the bomb in the icon. W e just want to get your attention because making an error could be costly . This is not really very technical stuff, just some details you need to really pay attention to. Int rod ucti on Cong ratul ation s on your d ecisi on to mou nt your T V with a TV W all M ountin g Kit For ...
-
Bell'O 8210DB - page 3
Precautions! • This mounting bracket was designed to be installed and utilized ONL Y as specified in this manual. Bell’O International Corporation will not be responsible for failure to assemble as directed or for the improper assembly , use, or handling of this product. • Improper installation of this product may cause damage or serious inju ...
-
Bell'O 8210DB - page 4
(WM) W all Mount Quantity: 1 (IG) Installation Guide & DVD Quantity: 1 each (IT) Installation T emplate Quantity: 1 (MP) Monitor Plate Quantity: 1 Parts Included in This Kit Installation Video for Bell’O TV Wal l Mounting Kits © J a n u a r y 2 0 0 7 B e l l ' O I n t e r n a t i o n a l C o r p o r a t i o n C o n t e n t s o f t h i s ...
-
Bell'O 8210DB - page 5
4 English Parts Included in This Kit (continued) (D) M4/M5 Short Spacer , Quantity: 6 (E) M4/M5 Long Spacer , Quantity: 6 (Q) M6/M8 Short Spacer , Quantity: 4 (P) M6/M8 Long Spacer , Quantity: 4 (S) M6/M8 Washer , Quantity: 4 (R) M4/M5 Washer , Quantity: 4 (G) M5 x 12mm TV Mounting Screw , Quantity: 6 (H) M5 x 22mm TV Mounting Screw , Quantity: 6 ( ...
-
Bell'O 8210DB - page 6
TOGGLER ® brand ALLIGA TOR ® SOLID-W ALL ANCHORS are patented under one or more of US Patent numbers 5,161,296 and 5,938,3 85; and foreign counterpar ts thereof and of 4,752,170. Other patents pending. TOGGLER and ALLIGATO R are worldwide registered trademarks of Mechanical Plastics Corp. (W) M4 x 160mm Security Screw , Quantity: 2 (V) Plastic Sl ...
-
Bell'O 8210DB - page 7
Getting ready to hang the TV Select the location where you want to mount the TV . Clear the area of all furniture and electronics. Y ou will need some elbow room to mount the TV . Y ou also want to make sure that your electronic devices are unplugged, covered, and out of way because you are about to start drilling holes, and that is likely to make ...
-
Bell'O 8210DB - page 8
T able 1: Standard Monitor Mounting Configurations Who is VESA? The V ideo El ectr oni cs Stan dard s As soci atio n is an int erna tio nal non prof it orga niza tio n rep res enti ng hard war e, soft ware , PC, di spla y , and co mpon ent man ufa ctur ers, ca ble and tel eph one com pan ies, an d ser vice pr ovid ers . VES A sup por ts and sets in ...
-
Bell'O 8210DB - page 9
DET AILED VIEW Back of TV F , R or S Selected Screw MP DET AILED VIEW Back of TV Figure 1 Use spacers in situations when the arms do not fit firmly against the back of the television, such as when the back of the television is curved, contains larger recessed mounting holes, or some other obstruction is in the way . If your TV requires use of a spa ...
-
Bell'O 8210DB - page 10
Using the 8190 Adapter Plates Some TVs have lar ger m ounting confi gurations (2 00 x 200, 20 0 x 150, or 200 x 100), an d the Monito r Plat e (MP ) alo ne can not r each t hese holes. If this is the cas e for yo ur TV , yo u need to use the inclu ded 8 190 A dapter Plates (A P). Figure 3 AG F MP MP AP AP AG F For 200x200 & 200x150 mounting con ...
-
Bell'O 8210DB - page 11
10 English Step 2: Securing the W all Mount Finding a wood stud to mount to Using a stud finder , determine the exact location of the stud to which you want to attach the wall mount. Using an electronic stud finder works best because it gives you an indication of where the right and left sides of the stud are. After you determine the stud location, ...
-
Bell'O 8210DB - page 12
11 English 16 Inches (406mm) Height to bottom of TV W ood Studs IT Level Figure 6 Determining the location of the TV After the Monitor Plate (MP) has been mounted to the TV , you can now measure the distance from the bracket holes to the top and bottom of the TV to help determine the desired height of the TV on your wall. The reason that you need t ...
-
Bell'O 8210DB - page 13
12 English Using the Installation T emplate The Installation T emplate (IT) included in this kit helps you select the correct positions for drilling the holes for the TV mounting. Figure 7 shows what the holes on the template represent. Y ou must be careful to accurately drill the holes or else the screws may not line up with the holes in your wall ...
-
Bell'O 8210DB - page 14
13 English When you have prepared the holes for mounting the wall mount, screw two of the Lag Bolts (T) three-quarters of the way into the holes. Leave enough room so you can slip the W all Mount (WM) over the screws. Install the wall mount as shown without tightening the screws completely . After the wall mount is on the wall, you can install the ...
-
Bell'O 8210DB - page 15
14 English When mounting to solid concrete, bricks, or cinder block Figure 9 Concrete Block W all Because drilling an accurate and clean hole is essential to securing your mount, be sure to use a new drill bit. An old drill bit can not only make an uneven hole, it can also break out the back of the concrete block which can diminish the holding abil ...
-
Bell'O 8210DB - page 16
15 English Figure 11 WM U T After the holes are drilled, remove the template and place the ALLIGA TOR ® Anchor (U) into the concrete wall as shown in Figure 10. After you have prepared the two holes for mounting the wall mount, screw the two bottom Lag Bolts (T) three-quarters of the way into the holes. Leave enough room so that you can slip the w ...
-
Bell'O 8210DB - page 17
16 English Preparing the security screws Y ou need to mount the Monitor Plate (MP) onto the W all Mount (WM). T o ensure it does not come off, you use two screws to secure the parts together . Y ou have two choices of screw sizes. For TVs under 20" (508mm) you can use the shorter 16mm Securit y Screws (X). If your TV is larger than 20" (5 ...
-
Bell'O 8210DB - page 18
17 English Figure 12B (For TVs over 20") WM V W If your audio, video, and power cables will not be accessible after you mount the TV , you need to make those connections now . Before doing this, however , make sure all TV and component power cords are not plugged into any electrical outlets and your audio and video equipment is turned off. Mak ...
-
Bell'O 8210DB - page 19
18 English Mounting the TV When you’re ready to put the Monitor Plate (MP) onto the W all Mount (WM), get a friend or an assistant to help you lift the TV and guide the Monitor Plate onto the W all Mount as shown in Figure 13. Afte r you’r e confi dent it is proper ly inst alled and the TV is secu rely mount ed to the wall , you need to tighte ...
-
Bell'O 8210DB - page 20
Limited Lifetime Warranty [Please note: Y ou are responsible to inspect your mount thoroughly for missing or defective parts immediately after opening the box. T o receive replacement or missing part(s) under this W arranty, visit our website at www .bello.com or call our Customer Service Department at 1-888-779-7781. Please have the model number, ...
Hai una domanda su Bell'O 8210DB?
Utilizza il modulo sottostante
Se non hai risolto il problema con Bell'O 8210DB con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Bell'O 8210DB è probabile che voglia condividere il modo di risolverlo.