Manuale per l’uso Chauvet SCAN LED 100

17 pagine 1.39 mb
Scarica

Vai alla pagina of 17

Summary
  • Chauvet SCAN LED 100 - page 1

    User Manual ...

  • Chauvet SCAN LED 100 - page 2

    CHAUVET®, 2010, All Rights Reserved Information and specifications in this User Manual are s ubject to change without notice. CHAUVET® assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. Author: Anthony Chiappone Revision: 01b Release Date: 11-12-2 010 T ABLE OF C ONTENTS 1. BEFORE YOU BEGIN ..... ...

  • Chauvet SCAN LED 100 - page 3

    1. Before You Begin 3 11/19/2010 11:07 AM 1. B EFORE Y OU B EGIN What is included • 1 x Intimidator™ Scan LED 100 • 1 x Hanging bracket • 1 x Power Cord • 1 x Warranty Card • 1 x User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, ...

  • Chauvet SCAN LED 100 - page 4

    1. Before You Begin 4 11/19/2010 11:07 AM Safety Instructions • Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. • Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher t han ...

  • Chauvet SCAN LED 100 - page 5

    2. Introduction 5 11/19/2010 11:07 AM 2. I NTRODUCTION Product Overview Power Out Microphone Sensitivity Adjustm ent knob Microphone Power In DMX Out Safety DMX In DIP Switches Fuseholder Power LED Indicato r Signal LED Indicator ...

  • Chauvet SCAN LED 100 - page 6

    3. Setup 6 11/19/2010 11:07 AM 3. S ETUP AC Power This fixture is auto-ranging and runs on 100~240 V AC, 50/60 Hz power. To determine the power requirements for a pa rticul ar fixture, see the label affixed to the back plate of the fixture or refer to the fixture’s s pecifications chart. A fixt ure’s listed current rating indicates its average ...

  • Chauvet SCAN LED 100 - page 7

    3. Setup 7 11/19/2010 11:07 AM Mounting Orientation The Intimidator™ Scan LED 100 may be mounted in any position provided there is adequate room for ventilation. Rigging Be sure that the structure can support the wei ght of the fixture. Pl ease see the “Technical Specifications” section of this m anual for a detailed weight listing. Mount the ...

  • Chauvet SCAN LED 100 - page 8

    4. Operating Instructions 8 11/19/2010 11:07 AM 4. O PERATING I NSTRUCTIONS Configuring the Starting Address The Intimidator™ Scan LED 100 fixture uses 6 DMX channels. In this DMX configuration/personality, the highest channel that the fixture may be se t to in order to function properly is 507 . Any address higher than this will prevent access t ...

  • Chauvet SCAN LED 100 - page 9

    4. Operating Instructions 9 11/19/2010 11:07 AM Standalone This fixture has several options for operating without a DMX controller. These options are accessed via the DIP switches on the back of the fixture. Please see the chart below for further explanation. DIP Switches Function 1 2 3 4 5 6 7 8 9 10 Dimmer 100% 3 25% 3 50% 3 75% Strobe Speed No S ...

  • Chauvet SCAN LED 100 - page 10

    4. Operating Instructions 10 11/19/2010 11:07 AM Sound-Active Access this mode via the DIP switches on the back of the fixture. T he chart on the previous page may be used to alter playback parameters. Please see the instructions below for details on entering this mode. 1. Unplug any DMX controller.  2. Turn the microphone sensitivity adjustment ...

  • Chauvet SCAN LED 100 - page 11

    5. Appendix 11 11/19/2010 11:07 AM 5. A PPENDIX General Troubleshooting S YMPTOM P OSSIBLE C AUS E ( S ) P OSSIBLE A CTION ( S ) Breaker/Fuse keeps blowing • Excessive circuit load • Check total load placed on the electrical circuit. • Short circuit along the power wires • Check for a short in the electrical wiring (internal and/or external ...

  • Chauvet SCAN LED 100 - page 12

    5. Appendix 12 11/19/2010 11:07 AM DMX Primer There are 512 channels in a DMX connection. A fixt ure capable of receiving DMX will require one or a number of sequential channels. The user must assign a starting address on the fi xture that indicates the first channel reserved in the cont roller. There are many different types of DMX controllable fi ...

  • Chauvet SCAN LED 100 - page 13

    5. Appendix 13 11/19/2010 11:07 AM Cable Connectors Cabling must have a male XLR connector on one end and a female XLR connector on the other end. Do not allow contact be twe en the common and the fixture’s ch assis ground. Grounding the common can caus e a ground loop, and y our fixture may perform erra tically. Test cables with an ohm meter to ...

  • Chauvet SCAN LED 100 - page 14

    5. Appendix 14 11/19/2010 11:07 AM 3-Pin to 5-Pin Conversion Chart If you use a controller with a 5-pin DMX output connector, you will ne ed to use a 5-pin t o 3-pin adapter. The char t bel ow details a proper cable c onversion: 3-P IN TO 5-P IN C ONVERSION C HAR T Conductor 3-Pin Female (Output) 5-Pin Male (Input) Ground/Shield Pin 1 Pin 1 Data ( ...

  • Chauvet SCAN LED 100 - page 15

    5. Appendix 15 11/19/2010 11:07 AM General Maintenance To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces light output perform ance and can cause ...

  • Chauvet SCAN LED 100 - page 16

    T ECHNICAL S PECIFICATIONS WEIGHT & DIMENSIONS Length ............................................................................................................. 5.7 in (14 5 mm) Width ............................................................................................................... 6.8 in (1 72 mm) Height ....................... ...

  • Chauvet SCAN LED 100 - page 17

    C ONTACT U S World Wi de General Information CHAUVET® 5200 NW 108 th Ave Sunrise, FL 33351 voice: 954.929.1115 fax: 954.929.5560 toll free: 800.762.1084 Technical Support CHAUVET® 5200 NW 108 th Ave Sunrise, FL 33351 voice: 954.929.1115 (Press 4) fax: 954.929.5560 ( Attention: Service) World Wide Web www.chauvetlighting.com ...

Fabbricante Chauvet Categoria Indoor Furnishings

I documenti che otteniamo dal fabbricante del dispositivoChauvet SCAN LED 100 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Chauvet
- manuali per l’uso SCAN LED 100
- schede prodotto Chauvet
- opuscoli
- o etichette energetiche Chauvet SCAN LED 100
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Chauvet SCAN LED 100.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Chauvet SCAN LED 100, manuali di manutenzione, brevi manuali o manuali utente Chauvet SCAN LED 100. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Chauvet SCAN LED 100.

Manuali per l’uso simili

Manuale completo del dispositivo Chauvet SCAN LED 100, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Chauvet SCAN LED 100 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Chauvet SCAN LED 100.

Il manuale per l’uso completo Chauvet, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Chauvet SCAN LED 100 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Chauvet SCAN LED 100, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Chauvet SCAN LED 100 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Chauvet SCAN LED 100 - che ci dovrebbe aiutare nei primi passi durante l'uso Chauvet SCAN LED 100
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Chauvet SCAN LED 100
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Chauvet SCAN LED 100 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Chauvet SCAN LED 100?

Utilizza il modulo sottostante

Se non hai risolto il problema con Chauvet SCAN LED 100 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Chauvet SCAN LED 100 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)