-
Invacare 1163197 - page 1
Owner’s Operator and Maintenance Manual DEALER: This manual MUST be g iven to the user of the wheelchair. USER: BEFORE using this wheelchair, read this manual and save for future reference. For more information regarding Invacare products, parts, and services, please visit www.invacare.com Insignia ™ ...
-
Invacare 1163197 - page 2
Insignia ™ 2 Part No. 1163197 WARNING A QUALIFIED TECHNICIAN MUST PERF ORM THE INITIAL SET UP OF THIS WHEELCHAIR. ALSO, A QUALIFIED TECHNICIAN MUST PERFORM ALL PROCEDURES SPECIFICALLY INDICATED IN THE MANUAL. DO NOT USE THIS PRODUCT OR ANY AVAILABLE OPTIONAL EQUIPMENT WITHOUT FIRST COMPLETELY READING AND UNDERSTANDING THESE INSTRUCTIONS AND A ...
-
Invacare 1163197 - page 3
TABLE OF CONTENTS Part No. 1163197 3 Insignia ™ TABLE OF CONTENTS SPECIAL NOTES ................................................................................................ 5 LABEL LOCATION ............................................................................................. 6 TYPICAL PRODUCT PARAMETERS ............................... ...
-
Invacare 1163197 - page 4
TABLE OF CONTENTS Insignia ™ 4 Part No. 1163197 TABLE OF CONTENTS SECTION 6—SEAT AN D BACK ......................................................................... 27 Removing/Installing the Seat Upholstery . .................................................................... ................... ..................... .......... 27 Removing/In ...
-
Invacare 1163197 - page 5
SPECIAL NOTES Part No. 1163197 5 Insignia ™ SPECIAL NOTES Signal wor ds are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage. Refer to the following table for defi ...
-
Invacare 1163197 - page 6
LABEL LOCATION Insignia ™ 6 Part No. 1163197 LABEL LOCATION Refer to Owner's Man ual for proper anti-tipper setting. 1085379 W ARNING WARNING DO NOT OPERATE WITHOUT THE ANTI-TIP TUBES INSTALLED. REV. 5/98 P/N 60106X144 Detent balls should extend bey ond the diameter of the axle bushing f or a positive lock. K eep detent balls clean. W ARNING ...
-
Invacare 1163197 - page 7
TYPICAL PRODUCT PARAMETERS Part No. 1163197 7 Insignia ™ TYPICAL PRODUCT PARAMETERS NOTE: The seat ‐ to ‐ floor heights are based on ur eth ane tires. If wheelchair is equipped with pneumatic flat free add 1 / 2 inch to the measurements listed abov ...
-
Invacare 1163197 - page 8
SECTION 1—GENERAL GUIDELINES Insignia ™ 8 Part No. 1163197 SECTION 1—GENERAL GUIDELINES WARNING SECTION 1 - GENERAL GU IDELINES contains im portant information for the safe operation and use of this product. Stability - All Models The sea t depth, back height/angle, seat angle, size/position of the ...
-
Invacare 1163197 - page 9
SECTION 1—GENERAL GUIDELINES Part No. 1163197 9 Insignia ™ Seat ‐ to ‐ floor angle of 0° or 3°: If so equipped, anti ‐ tippers must be attached at all times. Inasmuch as the anti ‐ tippers are an option for 0° or 3° on thi ...
-
Invacare 1163197 - page 10
SECTION 1—GENERAL GUIDELINES Insignia ™ 10 Part No. 1163197 DO NOT attempt to lift the wheelchair by any remov able (detachable) parts. Lifting by means of any remov able (detachable) parts of the wheelchair may result in injury to th ...
-
Invacare 1163197 - page 11
SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Part No. 1163197 11 Insignia ™ SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Safety/Handling of Wheelchairs Safety and handling of the wheelchair require the close attention of the wheelchair user as we l l as the assistant. This ? ...
-
Invacare 1163197 - page 12
SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Insignia ™ 12 Part No. 1163197 A Note to Wheelchair Assistants When assistance to the wheelchair user is required, remember to us e good body mechanics. Keep you r back straight and bend you r knees whenever tippi ...
-
Invacare 1163197 - page 13
SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Part No. 1163197 13 Insignia ™ Tipping WARNING DO NOT tip the wheelcha ir without assistance. ALWAYS check hand grips for loo seness before using the wheelch air. If loose and/or worn, replace IMMEDIATELY. When tipping the wheelchair , an assistant should grasp the ...
-
Invacare 1163197 - page 14
SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Insignia ™ 14 Part No. 1163197 WARNING When lowering the front casters of the wheelchair, DO NOT let th e wheelchair drop the last few inches to the ground. Th is could result in injury to th e occupant and/or damage to the wheelchair. Roll the wheelchair backward and slowly l ...
-
Invacare 1163197 - page 15
SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Part No. 1163197 15 Insignia ™ Escalators WARNING DO NOT use an escalator to move a wheelchair between floors. Serious bo dily injury may occur. Transferring To a nd From Other Seats WARNING Before attempting to tr ansfer in or out of the wheelchair, every precauti on should be taken to reduce th ...
-
Invacare 1163197 - page 16
SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Insignia ™ 16 Part No. 1163197 4. Press downw ard on the top of the seat rail until the wheelchair is fully open and the seat rails are fully seated in the H ‐ blocks. 5. Engage both wheel locks, ...
-
Invacare 1163197 - page 17
SECTION 3—SAFETY INSPECTION/TROUBLESHOOTING Part No. 1163197 17 Insignia ™ SECTION 3—SAFETY INSPECTION/TROUBLESHOOTING NOTE: Every six months or as necessary , take your wheelchair to a qualifi ed technician for a thorough inspection and servicin g. Regular cl ...
-
Invacare 1163197 - page 18
SECTION 3—SAFETY INSPECTION/TROUBLESHOOTING Insignia ™ 18 Part No. 1163197 ❑ Ensure all spokes are uniformly tight. ❑ Inspect axle assembly for proper tension by spinning caster . Caster should come to a gradual stop. ❑ Inspect front caster for ...
-
Invacare 1163197 - page 19
SECTION 3—SAFETY INSPECTION/TROUBLESHOOTING Part No. 1163197 19 Insignia ™ Maintenance Maintenance Safety Precautions WARNING After any adjustments, re pair or service and before use, make sure all attac hing hardware is tightened securely. Otherwise in jury or damage may result. CAUTION DO NOT overtighten hard ware attaching to the fr ame. ...
-
Invacare 1163197 - page 20
SECTION 4—FRONT RIGGINGS Insignia ™ 20 Part No. 1163197 SECTION 4—FRONT RIGGINGS WARNING After any adjustments, re pair or service and before use, make sure all attac hing hardware is tightened securely. Otherwise injury or damage may occur. Installing/Removing Front Riggings Assembly NOTE: For this procedur e, ref e r ...
-
Invacare 1163197 - page 21
SECTION 4—FRONT RIGGINGS Part No. 1163197 21 Insignia ™ Adjusting Footplate Height NOTE: For this procedur e, ref e r to FIGURE 4.2 on page 21. NOTE: This procedure applies to the swingaway front riggings and swingaway elevating legr est. 1. Remove the front ...
-
Invacare 1163197 - page 22
SECTION 4—FRONT RIGGINGS Insignia ™ 22 Part No. 1163197 Replacing Heel Loop NOTE: For this procedur e, ref e r to FIGURE 4.4. 1. Pull the cam lock lever down to the unlocked position. 2. Push in the release buttons and remove the footplate assembly ? ...
-
Invacare 1163197 - page 23
SECTION 5—ARMS Part No. 1163197 23 Insignia ™ SECTION 5—ARMS WARNING After any adjustments, re pair or service and before use, make sure all attac hing hardware is tightened securely. Otherwise injury or damage may occur. Removing/Installing the Armrest NOTE: For this procedur e, ref e r to FIGURE 5.1. Removing 1. ...
-
Invacare 1163197 - page 24
SECTION 5—ARMS Insignia ™ 24 Part No. 1163197 Using Flip Back Armrest NOTE: For this procedur e, ref e r to FIGURE 5.2. 1. Unlock the flip back armrest by pressing the relea se lever toward the front of the wheelchair . 2. Pull the front of the ? ...
-
Invacare 1163197 - page 25
SECTION 5—ARMS Part No. 1163197 25 Insignia ™ FIGURE 5.3 Removing/Installing the Flip Back Arm Replacing Clothing Guards NOTE: For this procedur e, ref e r to FIGURE 5.4. 1. Remove the flip back arm. Refer to Removing/Installing the Flip Back Arm on page 24. 2. Remove ? ...
-
Invacare 1163197 - page 26
SECTION 5—ARMS Insignia ™ 26 Part No. 1163197 Changing from Full Length Armrest to Desk Length Armrest and Vice Versa NOTE: For this procedur e, ref e r to FIGURE 5.5 on page 26. 1. Remove the ar mrest. 2. Rotate armrest 180°, ensuring that the scalloped edge of the ? ...
-
Invacare 1163197 - page 27
SECTION 6—SEAT AND BACK Part No. 1163197 27 Insignia ™ SECTION 6—SEAT AND BACK WARNING After any adjustments, re pair or service and before use, make sure all attac hing hardware is tightened securely. Otherwise injury or damage may occur. Removing/Installing the Seat Upholstery Removing NOTE: For this procedur e, ref e r ...
-
Invacare 1163197 - page 28
SECTION 6—SEAT AND BACK Insignia ™ 28 Part No. 1163197 7. Remove seat cushion. FIGURE 6.2 Removing/Installing the Seat Cushion Removing/Installing the Back Upholstery Removing NOTE: For this procedur e, ref e r to FIGURE 6.3 on page 29. 1. Remove the tw o mounting screws and wa ...
-
Invacare 1163197 - page 29
SECTION 6—SEAT AND BACK Part No. 1163197 29 Insignia ™ FIGURE 6.3 Removing/Installing the Back Upholstery Adjusting Back Height, Back Angle or Seat Depth WARNING The seat depth, back height/angle, seat angle, size/position of the front casters, s ize/position of the rear wheels, anti-tipper model, as well as the us er condition directly rel ...
-
Invacare 1163197 - page 30
SECTION 7—REAR WHEELS Insignia ™ 30 Part No. 1163197 SECTION 7—REAR WHEELS WARNING After any adjustments, re pair or service and before use, make sure all attac hing hardware is tightened securely. Otherwise injury or damage may occur. Removing/Installing Rear Wheels WARNING Only a qualified technician may change the size of the rear ...
-
Invacare 1163197 - page 31
SECTION 7—REAR WHEELS Part No. 1163197 31 Insignia ™ FIGURE 7.1 Removing/Installing Rear Wheels - Removing Adjusting Quick-Release Axle WARNING Make sure detent pin and detent balls of the quick-release axles are fully released before operating the wheelchair. Keep detent balls clean. NOTE: For this procedur e, ref e r t ...
-
Invacare 1163197 - page 32
SECTION 7—REAR WHEELS Insignia ™ 32 Part No. 1163197 5. Reinstall rear wheel onto the wheelchair . Refer to Removing/Installing Rear Wheels on page 30. FIGURE 7.2 Adjusting Quick-Release Axle Replacing Rear Wheel Handrim NOTE: For this procedur e, ref e r to FIGURE 7.3. 1. ...
-
Invacare 1163197 - page 33
SECTION 8—FRONT CASTERS Part No. 1163197 33 Insignia ™ SECTION 8—FRONT CASTERS WARNING After any adjustments, re pair or service and before use, make sure all attac hing hardware is tightened securely. Otherwise injury or damage may occur. Removing/Installing Front Casters NOTE: For this procedur e, ref e r to FIGU ...
-
Invacare 1163197 - page 34
SECTION 8—FRONT CASTERS Insignia ™ 34 Part No. 1163197 6. T est wheelchair for maneuverability . 7. Readjust locknuts if neces sary , and repeat STEPS 5 ‐ 6 until correct. 8. Snap dust cover ov er the locknut and st em (Detail “C”). FIGURE 8.2 Removing/Ins ...
-
Invacare 1163197 - page 35
SECTION 8—FRONT CASTERS Part No. 1163197 35 Insignia ™ Replacing/Repairing Front Caster Tire/Tube WARNING Replacement of front caster ti re or tube MUST be performe d by a qualified technician. CAUTION As with any vehicle, check the wheels and tires pe riodically for cracks and wear. Replace if dam aged. Adjusting Front Caster Mounting ...
-
Invacare 1163197 - page 36
SECTION 9—WHEEL LOCKS Insignia ™ 36 Part No. 1163197 SECTION 9—WHEEL LOCKS WARNING After any adjustments, re pair or service and before use, make sure all attac hing hardware is tightened securely. Otherwise injury or damage may occur. If wheel locks DO NOT hold the occupied wheelchair in place, contact a qualif ied technician. Otherwise ...
-
Invacare 1163197 - page 37
SECTION 9—WHEEL LOCKS Part No. 1163197 37 Insignia ™ 8. If wheel lock is unable to properly engage the wheel, contact yo ur local dealer or Inv acare at the number on the back cover . 9. Repeat STEPS 1 ‐ 9 for the opposite wheel ...
-
Invacare 1163197 - page 38
SECTION 10—ANTI-TIPPERS Insignia ™ 38 Part No. 1163197 SECTION 10—ANTI-TIPPERS WARNING After any adjustments, re pair or service and before use, make sure all attac hing hardware is tightened securely. Otherwise injury or damage may occur. Installing/Adjusting Anti-tippers WARNING Anti-tippers are sp ecific to the different seat-to-fl ...
-
Invacare 1163197 - page 39
SECTION 10—ANTI-TIPPERS Part No. 1163197 39 Insignia ™ FIGURE 10.1 Installing Anti-Tippers Changing Orientation of Anti-Tip Wheels NOTE: For this procedur e, ref e r to FIGURE 10.2. 1. Pull the spring loaded anti tipper out and rotate up or down. 2. Rotate until ant ...
-
Invacare 1163197 - page 40
SECTION 10—ANTI-TIPPERS Insignia ™ 40 Part No. 1163197 Adjusting Anti-Tippers NOTE: For this procedur e, ref e r to FIGURE 10.3. 1. Press the release buttons on the wheeled po rtio n of the anti ‐ tipper and slide it up or down to achiev e the ...
-
Invacare 1163197 - page 41
SECTION 11—OPTIONS Part No. 1163197 41 Insignia ™ SECTION 11—OPTIONS WARNING After any adjustments, re pair or service and before use, make sure all attac hing hardware is tightened securely. Otherwise injury or damage may occur. The I.V./O2 holder MUST be checked weekly to en sure it is tightly secu red to the wh eelchair frame. If there ...
-
Invacare 1163197 - page 42
SECTION 11—OPTIONS Insignia ™ 42 Part No. 1163197 FIGURE 11.1 Installing/Removing the I.V. Holder - Ad justing the Height of the I.V. Holder Installing/Removing the O2 Holder CAUTION The O2 holder can only be instal led on the left side due to th e angle of the plate between the step tube and the O2 holder frame. Installati on of the O2 holder ...
-
Invacare 1163197 - page 43
SECTION 11—OPTIONS Part No. 1163197 43 Insignia ™ 4. Secure the mounting bracket of the O2 holder and bac k upholstery to the back cane with the mounting screw removed in STEP 2. Tighten securely (Detail “A ” ) . 5. Press the re l ...
-
Invacare 1163197 - page 44
SECTION 11—OPTIONS Insignia ™ 44 Part No. 1163197 Using the O2 Holder WARNING Only use O2 cylinders that are at least 10.7 inches in height and 4 3 / 8 inches in diam eter. Smaller O2 cylinders will not secure in place properly which may result in injury and/or damage to the cylinder. NOTE: For this procedur e, refe r to ...
-
Invacare 1163197 - page 45
SECTION 11—OPTIONS Part No. 1163197 45 Insignia ™ Installing/Removing the IV/O2 Holder CAUTION The IV/O2 holder can only be inst alled on the left side due to th e angle of the pl ate between the step tube and the IV /O2 holder frame. Installati on of the IV/O2 holder on the right side cannot be achieved due to interferen ce of the IV/O2 holder ...
-
Invacare 1163197 - page 46
SECTION 11—OPTIONS Insignia ™ 46 Part No. 1163197 FIGURE 11.5 Installing/Removing the IV/O2 Holder Using the IV/O2 Holder WARNING Only use O2 cylinders th at are at least 24.9 in ches in height and 4 3 / 8 inches in diameter. Smaller O2 cylinders will not properly secure in place whic h may result in injury and/or damage to the O2 cylinder. ...
-
Invacare 1163197 - page 47
SECTION 11—OPTIONS Part No. 1163197 47 Insignia ™ FIGURE 11.6 Using the IV/O2 Holder Adjusting the Height of the IV Pole NOTE: For this procedur e, ref e r to FIGURE 1 1.7. 1. Loosen the height adjustment knob on the IV/O2 holder . 2. Adjust the IV pole to the des i ...
-
Invacare 1163197 - page 48
SECTION 11—OPTIONS Insignia ™ 48 Part No. 1163197 Installing Crutch and Cane Carrier WARNING Check base weekly to en sure proper placement. When loading the crutch/cane carrier , ensure items are securely plac ed into the base. Also ensure that there is no interference wi th folding the wheelcha ir, the rear wheels, or the swing-back arms. ...
-
Invacare 1163197 - page 49
SECTION 11—OPTIONS Part No. 1163197 49 Insignia ™ FIGURE 11.9 Installing/Removing the Seat Positioning Strap DETAIL “A” Buckle Buckle Strap Tongue Tongue Strap DETAIL “B” Mounting Screw and Locknut Buckle Strap NOTE: Right side of wheelchair shown. Rear wheel removed for cl arity . Right Side of W ...
-
Invacare 1163197 - page 50
SECTION 11—OPTIONS Insignia ™ 50 Part No. 1163197 NOTES ...
-
Invacare 1163197 - page 51
LIMITED WARRANTY Part No. 1163197 51 Insignia ™ LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANU FACTURED AFTER JULY 4, 1975. This warranty is extended only to the original purchas er who purchases this product when new and unused from Invacare or a dealer . This warranty is ...
-
Invacare 1163197 - page 52
Invacare Corporation www.invacare.com USA One Invacare Way Elyria, Ohio USA 44036-2125 800-333-6900 Canada 570 Matheson Blvd E Uni t 8 Mississauga Ontario L4Z 4G4 Canada 800-668-5324 © 2010 Invacare Corporation. All rights reserved. Republication, duplication or modification in whole or in part is prohibited without prior written permission from I ...
Hai una domanda su Invacare 1163197?
Utilizza il modulo sottostante
Se non hai risolto il problema con Invacare 1163197 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Invacare 1163197 è probabile che voglia condividere il modo di risolverlo.