Italiano dropdown-ico

Manuale per l’uso LightSpeed Technologies LES 600 Series

21 pagine 0.34 mb
Scarica

Vai alla pagina of 21

Summary
  • LightSpeed Technologies LES 600 Series - page 1

    May 2002 1-800-732-8999 www .lightspeed-tek.com LightSPEED T echnologies, Inc. User Manual LES 600 Series Listening Enhancement System tm for Sound-Field Classroom Amplification ...

  • LightSpeed Technologies LES 600 Series - page 2

    Several studies validated by the U.S. Department of Education and the Educational Audiology Association verify that poor classroom acoustics, high ambient noise, and temporary mild hearing loss among children place many students academically at risk. The Sound-Field FM Classroom Amplification provided by the LES 600 incr eases both the volume and c ...

  • LightSpeed Technologies LES 600 Series - page 3

    4 LES 600 OPERA TING INSTRUCTIONS Power for Y our LES 600 Receiver/Amplifier 1 Check that: • Both front panel micr ophone volume controls (MIC 1 VOLUME and MIC 2 VOLUME) are set to minimum (turned fully counter -clockwise). • The Receiver/Amplifier is connected to a power source: Use the enclosed AC/DC power adapter to plug into a power cord or ...

  • LightSpeed Technologies LES 600 Series - page 4

    LES 600 OPERA TING INSTRUCTIONS 5 Power for Y our Belt-Pack T ransmitter & Microphone 1 Ensure the Belt-pack T ransmitter is turned OFF . 2 Y our Belt-pack T ransmitter has its internal rechargeable batteries already installed. Connect one end of the Charging Cable to one of the TRANSMITTER CHARGING jacks on the back panel of the Receiver/ Ampl ...

  • LightSpeed Technologies LES 600 Series - page 5

    6 LES 600 OPERA TING INSTRUCTIONS 4 NiMH batteries will usually maintain their charge for a full day of normal classroom use. Always switch the T ransmitter OFF when not in use (lunch hour , quiet times, etc.). Should the batteries in the T ransmitter need to be changed, open the lower plastic cover by pressing the ribbed portions on both sides of ...

  • LightSpeed Technologies LES 600 Series - page 6

    LES 600 OPERA TING INSTRUCTIONS 7 Positioning Y our Microphone After the microphone is connected to the belt-pack T ransmitter , position the microphone as described below: 1 Lavaliere Micr ophone : The lavaliere microphone should be hung around the neck as illustrated, r esting on your collar bone. The neck cord is adjusted by squeezing the two lo ...

  • LightSpeed Technologies LES 600 Series - page 7

    8 LES 600 OPERA TING INSTRUCTIONS 3 When speaking at a normal voice level, the green AF INDI- CA TOR on the Receiver/Amplifier fr ont panel should flash on and off as the voice level goes up and down. While speaking at a conversational voice level, slowly turn the MIC 1 VOLUME control knob clockwise to incr ease the loudness of the speakers until t ...

  • LightSpeed Technologies LES 600 Series - page 8

    3 The batteries will fully charge in about 8-12 hours. 4 When in normal use, it is best to leave batteries on the charger until used, since there is a small amount of discharge after 48 hours. However , do not leave battery(ies) plugged into the charger for mor e than 5 days as it will significantly shorten your battery life. 5 Once the batteries a ...

  • LightSpeed Technologies LES 600 Series - page 9

    Connecting to Other Audio Equipment 10 LES 600 OPERA TING INSTRUCTIONS 8 When speaking at a normal voice level, the green AF indi- cator light (on the Receiver/Amplifier front panel) should flash on and off as the voice level goes up and down. While speaking at a normal voice level, slowly turn the MIC 1 VOLUME or MIC 2 VOLUME (if applicable) contr ...

  • LightSpeed Technologies LES 600 Series - page 10

    LES 600 OPERA TING INSTRUCTIONS 11 and T elex transmitters use 2.5mm and 3.5mm audio input jacks, respectively . W ith the Receiver/Amplifier tur ned ON, increase the Mixed Audio Output LEVEL ADJUST slowly clockwise until you reach a comfortable volume. Connecting to A LightSPEED CX-50 Receiver A 1/4” phone-to-RCA cable is used. The 1/4” phone ...

  • LightSpeed Technologies LES 600 Series - page 11

    12 LES 600 OPERA TING INSTRUCTIONS These helpful suggestions are pr ovided to maximize the successful use of your new Classroom Amplification system: • Involve your students in this new process right fr om the beginning. When setting the volume, ask the students, “What is the correct volume?” (Each level will seem “louder” for them than y ...

  • LightSpeed Technologies LES 600 Series - page 12

    • T ur n the body-pack T ransmitter and/or the Hand-held Microphone OFF whenever leaving the classr oom. • Recharge batteries each night. Operating time (actual usage) f or the T ransmitter when using the rechar geable batteries should be more than adequate for a typical school day . Y our rechar geable batteries should last for a normal school ...

  • LightSpeed Technologies LES 600 Series - page 13

    14 LES 600 OPERA TING INSTRUCTIONS Power Indicator: When power is switched on, the red POWER light will come on. Radio Frequency Indicator: The RF Indicator displays that the LES 600 is receiving a radio signal from the instructor’ s body-pack T ransmitter (or Hand- held Microphone). When the T ransmitter is turned ON the amber RF Indicator will ...

  • LightSpeed Technologies LES 600 Series - page 14

    Power and V olume Switch for Microphones: Rotating the Mic 1 V olume control or Mic 2 V olume contr ol clockwise past the first “click” turns the LES 600 on. Continuing to rotate this knob clockwise will incr ease the volume of the wireless micr ophone through the speaker system. Aux1 and Aux2 V olume Control: Rotating the Auxiliary V olume Con ...

  • LightSpeed Technologies LES 600 Series - page 15

    17 & 19 16 LES 600 OPERA TING INSTRUCTIONS DC Power Connector: The Receiver/Amplifier requires a 15-volt, 2.4 Amp DC power supply . The center conductor is positive (+) polarity . Caution : Power supplies from different manufactur ers have various output voltages, current ratings, and polarity . Connecting the wrong type of power supply can res ...

  • LightSpeed Technologies LES 600 Series - page 16

    LES 600 OPERA TING INSTRUCTIONS 17 Aux1 and Aux2 Input Jacks: The AUXILIAR Y INPUT jack is used to connect to an external audio source (for example, a CD or tape player to add back- ground music) to mix with your voice audio fr om the wireless microphone. AUX1 level is adjusted by using the AUX1 VOLUME on the front; AUX2 is adjusted by AUX2 VOLUME. ...

  • LightSpeed Technologies LES 600 Series - page 17

    18 LES 600 OPERA TING INSTRUCTIONS Please go through this checklist befor e calling LightSPEED T echnologies Service Department. Battery Check • T ransmitters are char ged via a jumper cable from the back of the Amplifier . Make sure plugs are secured, and in the pr oper jacks. • Confirm the CHARGING light located on the front panel of the ampl ...

  • LightSpeed Technologies LES 600 Series - page 18

    LES 600 OPERA TING INSTRUCTIONS 19 Low V olume • Check volume level on Receiver and adjust as necessary . • If volume is too low , check the “MT” adjustment inside the battery compartment of the belt-pack T ransmitter . Clockwise adjustment of the “MT pot” will increase volume. Sound Fades In and Out (Drop Out) • Confirm Amplifier ant ...

  • LightSpeed Technologies LES 600 Series - page 19

    20 LES 600 OPERA TING INSTRUCTIONS • Check to confirm speaker wires are in the corr ect wire terminals on the back of the Receiver/Amplifier and confirm that the speaker switch for that speaker output is in the ON position. Black (or black stripe) to black terminal. White or gray wire to red terminal. T ransmitter Care • Cleaning the microphone ...

  • LightSpeed Technologies LES 600 Series - page 20

    LES 600 OPERA TING INSTRUCTIONS 21 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interfer ence that may cause undesired operation. Changes or modifications not expressly ...

  • LightSpeed Technologies LES 600 Series - page 21

    22 LES 600 OPERA TING INSTRUCTIONS Five Year Limited Warranty to Original Purchaser LightSPEED 600-series Classroom Amplification Systems ar e guaranteed against malfunction due to defects in materials and workmanship for a period of five years, beginning at the date o f the purchase invoice. If such malfunction occurs, the pr oduct will be repaire ...

Fabbricante LightSpeed Technologies Categoria Stereo Amplifier

I documenti che otteniamo dal fabbricante del dispositivoLightSpeed Technologies LES 600 Series possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici LightSpeed Technologies
- manuali per l’uso LES 600 Series
- schede prodotto LightSpeed Technologies
- opuscoli
- o etichette energetiche LightSpeed Technologies LES 600 Series
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso LightSpeed Technologies LES 600 Series.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione LightSpeed Technologies LES 600 Series, manuali di manutenzione, brevi manuali o manuali utente LightSpeed Technologies LES 600 Series. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto LightSpeed Technologies LES 600 Series.

Manuali per l’uso simili

Manuale completo del dispositivo LightSpeed Technologies LES 600 Series, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare LightSpeed Technologies LES 600 Series dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti LightSpeed Technologies LES 600 Series.

Il manuale per l’uso completo LightSpeed Technologies, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale LightSpeed Technologies LES 600 Series - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice LightSpeed Technologies LES 600 Series, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per LightSpeed Technologies LES 600 Series che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo LightSpeed Technologies LES 600 Series - che ci dovrebbe aiutare nei primi passi durante l'uso LightSpeed Technologies LES 600 Series
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del LightSpeed Technologies LES 600 Series
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio LightSpeed Technologies LES 600 Series in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su LightSpeed Technologies LES 600 Series?

Utilizza il modulo sottostante

Se non hai risolto il problema con LightSpeed Technologies LES 600 Series con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con LightSpeed Technologies LES 600 Series è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)