Italiano dropdown-ico

Manuale per l’uso Silicon Laboratories SI4734/35-B20

38 pagine 0.34 mb
Scarica

Vai alla pagina of 38

Summary
  • Silicon Laboratories SI4734/35-B20 - page 1

    Rev. 1.0 4/08 Copyright © 2008 by Silicon Laborato ries Si4734/35-B20 Si4734/35-B20 B ROADCAST AM/FM/SW/L W R ADIO R ECEIVER Features Applications Description The Si4734/35 is the first digital CMOS AM/FM/SW/L W radio receiver IC that integrates the complete tuner function from antenna input to audio outpu t. Functional Block Diagram  Worldwide ...

  • Silicon Laboratories SI4734/35-B20 - page 2

    Si4734/35-B20 2 Rev. 1.0 ...

  • Silicon Laboratories SI4734/35-B20 - page 3

    Si4734/35-B20 Rev. 1.0 3 T ABLE OF C ONTENT S Section Page 1. Electrical Specificat ions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Typical Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3. Bill of Materials . . . . . ...

  • Silicon Laboratories SI4734/35-B20 - page 4

    Si4734/35-B20 4 Rev. 1.0 1. Electrical S pecifications T able 1. Recommended Operating Conditions Parameter Symbol T est Condition Min T yp Max Unit Supply V oltage V DD 2.7 — 5.5 V Interface Supply V olt age V IO 1.5 — 3.6 V Power Supply Powe rup Rise Time V DDRISE 10 — — µs Interface Power Supply Powerup Rise Time V IORISE 10 — — µs ...

  • Silicon Laboratories SI4734/35-B20 - page 5

    Si4734/35-B20 Rev. 1.0 5 T able 3. DC Characteristics (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Condition Min T yp Max Unit FM Mode Supply Current I FM —1 9 . 2 2 2 m A Supply Current 1 I FM Low SNR level — 19.8 23 mA RDS Supply Curren t 2 I FM —1 9 . 9 2 3 m A Supply Current 2 I FMD Digital Ou ...

  • Silicon Laboratories SI4734/35-B20 - page 6

    Si4734/35-B20 6 Rev. 1.0 Figure 1. Reset Timing Parameters for Busmode Select T able 4. Reset Timing Ch aracteristics 1,2,3 (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol Min T yp Max Unit RST Pulse Width and GPO1, GPO2/INT Setup to R ST ↑ 4 t SRST 100 — — µs GPO1, GPO2/INT Hold from R ST ↑ t HRST 30 ? ...

  • Silicon Laboratories SI4734/35-B20 - page 7

    Si4734/35-B20 Rev. 1.0 7 T able 5. 2-Wire Control Interface Characteristics 1,2,3 (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Condition M in T yp Max Unit SCLK Frequency f SCL 0— 4 0 0 k H z SCLK Low Time t LOW 1.3 — — µs SCLK High Time t HIGH 0.6 — — µs SCLK Input to SDIO ↓ Setup (START) ...

  • Silicon Laboratories SI4734/35-B20 - page 8

    Si4734/35-B20 8 Rev. 1.0 Figure 2. 2-Wire Control Interface Read and W rite Timing Parameters Figure 3. 2-Wire Control Interface Read and W rite Timing Diagram SCLK 70% 30% SDIO 70% 30% START START STOP t f:IN t r:IN t LOW t HIGH t HD:STA t SU:STA t SU:STO t SP t BUF t SU:DAT t r:IN t HD:DA T t f:IN, t f:OU T SCLK SDI O START STOP ADDRESS + R/W ACK ...

  • Silicon Laboratories SI4734/35-B20 - page 9

    Si4734/35-B20 Rev. 1.0 9 Figure 4. 3-Wire Control Interface W rite T iming Parameters Figure 5. 3-Wire Control Interface Rea d Tim ing Parameters T able 6. 3-Wire Control Interface Characteristics (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Cond it ion Min T yp Max Uni t SCLK Frequency f CLK 0— 2 . 5 ...

  • Silicon Laboratories SI4734/35-B20 - page 10

    Si4734/35-B20 10 Rev. 1.0 Figure 6. SPI Control Interface Write T iming Parameters Figure 7. SPI Control Interface Read T iming Parameters T able 7. SPI Control Interface Characteristics (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Cond it ion Min T yp Max Uni t SCLK Frequency f CLK 0— 2 . 5 M H z SCL ...

  • Silicon Laboratories SI4734/35-B20 - page 11

    Si4734/35-B20 Rev. 1.0 11 Figure 8. Digit al Audio Interface T iming Parameters, I 2 S Mode T able 8. Digital Audio Int erface Characteristics (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Condition Min T yp Max Unit DCLK Cycle Time t DCT 26 — 1000 ns DCLK Pulse Width High t DCH 10 — — ns DCLK Puls ...

  • Silicon Laboratories SI4734/35-B20 - page 12

    Si4734/35-B20 12 Rev. 1.0 T able 9. FM Receiver Characteristics 1,2 (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Condition Min T yp Max Unit Input Frequency f RF 76 — 108 MHz Sensitivity with Headphone Network 3,4,5 (S+N)/N = 26 dB — 2.2 3 .5 µV EMF Sensitivity with 50 Ω Network 3,4,5,6 (S+N)/N = ...

  • Silicon Laboratories SI4734/35-B20 - page 13

    Si4734/35-B20 Rev. 1.0 13 Seek/Tune Time 6 RCLK to lerance =1 0 0p p m — — 80 ms/channel Powerup Time 6 From powerdown — — 1 10 ms RSSI Offset 12 Input levels of 8 and 60 dBµV at RF Input –3 — 3 dB T able 9. FM Receiver Characteristics 1,2 (Continued) (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol ...

  • Silicon Laboratories SI4734/35-B20 - page 14

    Si4734/35-B20 14 Rev. 1.0 T able 10. 64–75.9 MHz Input Frequency FM Receiver Characteristics 1 (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Condition Min T yp Max Unit Input Frequency f RF 64 — 75.9 MHz Sensitivity with Headphone Network 2,3,4,5 (S+N)/N = 26 dB — 4.0 — µV EMF LNA Input Resistan ...

  • Silicon Laboratories SI4734/35-B20 - page 15

    Si4734/35-B20 Rev. 1.0 15 T able 1 1. AM/SW/L W Receiver Characteristics 1 (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Condition Min T yp Ma x Unit Input Frequency f RF Long Wave (L W) 153 — 279 kHz Medium Wave (AM) 520 — 1710 kHz Short Wa ve (SW) 2.3 — 21 .8 5 MHz Sensitivity 2,3,4,5, 6 (S+N)/N ...

  • Silicon Laboratories SI4734/35-B20 - page 16

    Si4734/35-B20 16 Rev. 1.0 T able 12. Reference Clock and Cryst al Characteristics (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Condit ion Min T yp Max Unit Reference Clo ck RCLK Supported F requencies * 31.130 32.768 40000.0 k Hz RCLK Frequency T o lerance –50 — 50 ppm REFCLK_PRESCALE 1 — 4095 REF ...

  • Silicon Laboratories SI4734/35-B20 - page 17

    Si4734/35-B20 Rev. 1.0 17 2. T ypical Application Schematic Notes: 1. Place C1 close to V DD pin. 2. All grounds connect directly to GND pl ane on PCB. 3. Pins 1 and 20 are no connects, leave floating. 4. T o ensure proper operation and receiver performance, follow the guidelines in “AN383: Antenna Sele ction and Universal Layout Guide.” Silico ...

  • Silicon Laboratories SI4734/35-B20 - page 18

    Si4734/35-B20 18 Rev. 1.0 3. Bill of Materials Component(s) V alue/Description Supplier C1 Supply bypass capacitor, 22 nF, ±20%, Z5U/X7R Murata C4 Capacitor, 18 pF, ±20%, Z5U/X7R Murata C5 Coupling capacitor, 0.47 µF, ±20%, Z5U/X7R Murata L1 Ferrite loop stick, 180 – 450 µH Jiaxin L2 4.7 µH Coilcraft U1 Si4734/35 AM/FM Radio Tuner Silicon L ...

  • Silicon Laboratories SI4734/35-B20 - page 19

    Si4734/35-B20 Rev. 1.0 19 4. Functional Description 4.1. Overview Figure 9. Functional Block Diagram The Si4734/35 is the indu stry's first fully integrated, 100% CMOS AM/FM/SW/L W radio receiver I C. Of fering unmatched integration and PCB sp ace savings, the Si4734/35 requ ires minima l external com ponents and less than 20 mm 2 of boa rd ar ...

  • Silicon Laboratories SI4734/35-B20 - page 20

    Si4734/35-B20 20 Rev. 1.0 4.2. Operating Modes The Si4734/35 ope rates in e ither an FM receive or an AM/SW/L W receive mode. In FM mode, radio signals are received on FMI (pin 2) an d processed by the FM front-end circuitry . In AM/SW/L W mode, radio signals are received on AMI (pin 4) an d processed by the AM front-end circuitry . In addition to ...

  • Silicon Laboratories SI4734/35-B20 - page 21

    Si4734/35-B20 Rev. 1.0 21 4.7. Digit al Audio Interface (Si4735 Only) The digit al audio interface opera tes in slave mode and supports three different aud io da ta formats:  I 2 S  Left-Justified  DSP Mode 4.7.1. Audio Dat a Formats In I 2 S mode, by default the MS B is captured on the second rising edge of DCLK following each DFS transit ...

  • Silicon Laboratories SI4734/35-B20 - page 22

    Si4734/35-B20 22 Rev. 1.0 Figure 10. I 2 S Digita l Audio Format Figure 1 1. Lef t-Justified Digit al Audio Format Figure 12. DSP Digit al Audio Format LEFT CHANNEL RIGHT CHAN NEL 1 DCLK 1 DCLK 13 2n n-1 n-2 13 2n n-1 n-2 LSB MSB LSB MSB DCLK DOUT DFS INVERTED DCLK (OFALL = 1) (OFALL = 0) I 2 S (OMODE = 0000 ) LEFT CHANNEL RIGHT CHANNEL 13 2n n-1 n ...

  • Silicon Laboratories SI4734/35-B20 - page 23

    Si4734/35-B20 Rev. 1.0 23 4.8. Stereo Audio Processing The output of the FM demod ulator is a stereo multiplexed (MPX) signal. The MPX st andard was developed in 1961, and is used worldwide. T oday's MPX signal format consist s of left + righ t (L+R) audio, left – right (L– R) audio, a 19 kHz pilot tone, and RDS/RBDS data as shown in Figur ...

  • Silicon Laboratories SI4734/35-B20 - page 24

    Si4734/35-B20 24 Rev. 1.0 4.13. T uning The frequency synt hesizer uses Silic on Laboratories’ proven tech nology , including a com pletely integrat ed VCO. The frequency synthesizer g enerates the quadrature local os cillator signal used to downconvert the RF input to a lo w intermediate frequen cy . The VCO frequency is locked to the re ference ...

  • Silicon Laboratories SI4734/35-B20 - page 25

    Si4734/35-B20 Rev. 1.0 25 word by driving SDIO low on the next falling edge of SCLK. Although the Si4734/35 will respond to only a single device address, th is address can b e changed with the SEN pin (note that the SEN pin is n ot used for signaling in 2-wire mode). When SEN = 0, the 7-bit device address is 0010001b. When SEN = 1, the address is 1 ...

  • Silicon Laboratories SI4734/35-B20 - page 26

    Si4734/35-B20 26 Rev. 1.0 will be ignored by the devic e if the transaction is aborted. For details on timing specifications and dia grams, refer to Figure 6 and Figure 7 on page 10. 4.17. GPO Output s The Si4734/35 provides fi ve general-purpo se output pins. The GPO pin s can be configu red to output a constant low , constant high, or high-imped ...

  • Silicon Laboratories SI4734/35-B20 - page 27

    Si4734/35-B20 Rev. 1.0 27 5. Commands and Properties T able 14. Si473x Command Summary Cmd Name Description 0x01 POWER_UP Power up device and mode selection. Modes include AM/SW/L W or FM receive, ana log or dig ital output , and re fe re nc e c loc k or cry stal suppo rt. 0x10 GET_REV Returns revision info rmation on the d evice. 0x1 1 POWER_DOWN ...

  • Silicon Laboratories SI4734/35-B20 - page 28

    Si4734/35-B20 28 Rev. 1.0 T able 15. Si473x Property Summary Prop Name Description Default 0x0001 GPO_IEN Enables inte rr upt sources. 0x0000 0x0102 DIGIT AL_OUTPUT_FORMA T Co nfigures the digit al output format (Si4735 only). 0x0000 0x0104 DIGIT AL_O UTPUT_ SAMPLE_RA TE Configures th e digital outpu t sample rate in 100 Hz steps. The digital outpu ...

  • Silicon Laboratories SI4734/35-B20 - page 29

    Si4734/35-B20 Rev. 1.0 29 0x1502 RDS_CONFIG Configures RDS setting. 0x0000 0x3100 AM_DEEMPHASIS Sets de-emphasis time const a nt. Can be set to 50 us. De- emphasis is disabled by default. 0x0000 0x3102 AM_CHANNEL_FIL TER Select s the bandwid th of the chan nel filter for AM/SW/L W recep- tion. The choices are 6, 4, 3, 2, or 1 (kHz). The default ban ...

  • Silicon Laboratories SI4734/35-B20 - page 30

    Si4734/35-B20 30 Rev. 1.0 6. Pin Descriptions: Si4734/35-GM Pin Number(s) Name Description 1, 20 NC No connect. L eave floating. 2F M I F M R F i n p u t s . 3 RFGND RF ground. Connect to ground plane on PCB. 4 AMI AM/SW/L W RF input. 5R S T Device reset (active low) input. 6 SEN Serial enable input (active low). 7 SCLK Serial clock input. 8 SDIO S ...

  • Silicon Laboratories SI4734/35-B20 - page 31

    Si4734/35-B20 Rev. 1.0 31 7. Ordering Guide Part Number* Description Package Ty p e Operating Te m p e r a t u r e Si4734-B20-GM AM/FM/SW/L W Broad cast Radio Receiver QFN Pb-free –20 to 85 °C Si4735-B20-GM AM/FM/SW/L W Broad cast Radio Receiver with RDS/RBDS QFN Pb-free –20 to 85 °C *Note: Ad d an “(R)” at th e end of the device part num ...

  • Silicon Laboratories SI4734/35-B20 - page 32

    Si4734/35-B20 32 Rev. 1.0 8. Package Markings (T op Marks) 8.1. Si4734/35 T op Mark 8.2. T op Mark Explanation Mark Method: YAG Laser Line 1 Marking: Part Number 34 = Si4734, 35 = Si4735 Firmware Revision 20 = Firmware Revision 2. 0 Line 2 Marking: Die Revisi o n B = Revision B Die TTT = Internal Code Internal tracking code. Line 3 Marking: Circle ...

  • Silicon Laboratories SI4734/35-B20 - page 33

    Si4734/35-B20 Rev. 1.0 33 9. Package Outlin e: Si4734/35 QFN Figure 14 illustrates the package details for the Si4734/35. T able 1 6 lists the values for the dimensio ns shown in the illustration. Figure 14. 20-Pin Quad Flat No-Lead (QFN) T able 16. Package Dimensions Symbol Millimeters Symbol Millimeters Min Nom Max Min Nom Max A 0.50 0.55 0.60 f ...

  • Silicon Laboratories SI4734/35-B20 - page 34

    Si4734/35-B20 34 Rev. 1.0 10. PCB Land Pattern: Si4734/35 QFN Figure 15 illustrates the PCB land pattern det ails for the Si4734/35-GM. T able 17 lists t he values for the dimensions shown in the illustration. Figure 15. PCB Land Pattern ...

  • Silicon Laboratories SI4734/35-B20 - page 35

    Si4734/35-B20 Rev. 1.0 35 T able 17. PCB Land Pattern Dimensions Symbol Millimeters Symbol Millimeters Min Max Min Max D 2.71 REF GE 2.10 — D2 1.60 1.80 W — 0.34 e 0.50 BSC X — 0.28 E 2 .71 REF Y 0.61 REF E2 1.60 1.80 ZE — 3.31 f 2.53 BSC ZD — 3 .31 GD 2.10 — Notes: General 1. All dimensions shown are in millime te rs (mm) unless otherw ...

  • Silicon Laboratories SI4734/35-B20 - page 36

    Si4734/35-B20 36 Rev. 1.0 1 1. Additional Reference Resources  EN55020 Compliance T est Certificate  AN231: Si4700/01 Headphon e and Antenna Interface  AN332: Universal Programming Guide  AN383: Antenna Selection and Univer sal Layout Guidelines  AN386: Si473x Ferrite Loop S tick Antenna Interface  AN388: Universal Evaluation Boar ...

  • Silicon Laboratories SI4734/35-B20 - page 37

    Si4734/35-B20 Rev. 1.0 37 D OCUMENT C HANGE L IST Revision 0.4 to Revision 1.0  Updated T able 1, “Recommended Operating Conditions,” on page 4.  Updated T able 3, “ DC Characte ristics,” on page 5.  Updated T able 5, “2-Wire Co ntr o l Inte rf ace Characterist ics 1,2,3 ,” on page 7.  Updated T able 8, “Digital Audio Inte ...

  • Silicon Laboratories SI4734/35-B20 - page 38

    Si4734/35-B20 38 Rev. 1.0 C ONT ACT I NFORMATION Silicon Laboratori es Inc. 400 West Cesar Chavez Austin, TX 78701 T el: 1+(512) 416-8500 Fax: 1+(512) 416-9669 T oll Free: 1+(877) 4 44-3032 Email: FMinfo@silabs.com Internet: www .silabs.com Silicon Laboratories and Silicon Labs are trademarks of Silico n Laboratories Inc. Other products or brandnam ...

Fabbricante Silicon Laboratories Categoria Radio

I documenti che otteniamo dal fabbricante del dispositivoSilicon Laboratories SI4734/35-B20 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Silicon Laboratories
- manuali per l’uso SI4734/35-B20
- schede prodotto Silicon Laboratories
- opuscoli
- o etichette energetiche Silicon Laboratories SI4734/35-B20
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Silicon Laboratories SI4734/35-B20.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Silicon Laboratories SI4734/35-B20, manuali di manutenzione, brevi manuali o manuali utente Silicon Laboratories SI4734/35-B20. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Silicon Laboratories SI4734/35-B20.

Manuali per l’uso simili

Manuale completo del dispositivo Silicon Laboratories SI4734/35-B20, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Silicon Laboratories SI4734/35-B20 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Silicon Laboratories SI4734/35-B20.

Il manuale per l’uso completo Silicon Laboratories, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Silicon Laboratories SI4734/35-B20 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Silicon Laboratories SI4734/35-B20, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Silicon Laboratories SI4734/35-B20 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Silicon Laboratories SI4734/35-B20 - che ci dovrebbe aiutare nei primi passi durante l'uso Silicon Laboratories SI4734/35-B20
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Silicon Laboratories SI4734/35-B20
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Silicon Laboratories SI4734/35-B20 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Silicon Laboratories SI4734/35-B20?

Utilizza il modulo sottostante

Se non hai risolto il problema con Silicon Laboratories SI4734/35-B20 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Silicon Laboratories SI4734/35-B20 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)