Italiano dropdown-ico

Manuale per l’uso Proware EP-2123J-S3S3

30 pagine Non applicabile
Scarica

Vai alla pagina of 30

Summary
  • Proware EP-2123J-S3S3 - page 1

    SAS to SAS/SATA II JBOD Subsystem User Manual Revision 1.1 ...

  • Proware EP-2123J-S3S3 - page 2

    SAS to SAS /SA T A II JB OD Sub syst em 2 User Manual Table of Contents Chapter 1 Introduction .................................................................................................... 3 1.1 Fea tures ................................................. ............................................................... ........................ ...

  • Proware EP-2123J-S3S3 - page 3

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 3 Chapter 1 Introduction The 12 bays EPICa JBOD Subsystem The EPICa EP-2123J/JD-S3S3 is a 19-inch 2U rackmount JBOD unit. I t comes with 12 hot-swappable bays and is the Pro ware's most versatile SAS/SATA II Disk Expa nsion system, ideal for high capacity and sca lability storage in most popul ...

  • Proware EP-2123J-S3S3 - page 4

    SAS to SAS /SA T A II JB OD Sub syst em 4 User Manual 1.1 Features Modular Design with Common Parts  Inventory control efficiency  Cost-saving benefits to the end-user Power Supply  Power Supply and cooling system contai ned in 1 module fo r efficient cooling  400W power supplies to meet the future HDD power consumption Enclosure  Mo ...

  • Proware EP-2123J-S3S3 - page 5

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 5 1.2 Technical Specifications Model EP-2123J-S3S3 / EP-2123JD-S3S3 RAID Controller JBOD JBOD Controller Single / Redundant Host Interface 4x mini SAS (3Gb/s) Disk Interface SAS 3Gb or SATA II SAS expander 4x mini SAS (3Gb/s) Capacity - Direct Attached 12 Disks - Expansion Refers to controller spec ...

  • Proware EP-2123J-S3S3 - page 6

    SAS to SAS /SA T A II JB OD Sub syst em 6 User Manual 1.3 Unpacking the JBOD Subsystem The shipping package c ontains the followi ng: NOTE: If any damage is fou nd, contact the de aler or ve ndor for assista nce. JBOD Subsystem Unit Two (2) power cords One serial cable (RJ11 to DB9) Note: Two serial cables for dual JBOD controllers One external Min ...

  • Proware EP-2123J-S3S3 - page 7

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 7 1.4 Identifying Parts of the JBOD Su bsystem The illustrations below iden tify the various parts of the expan sion chassis. 1.4.1 Front View ...

  • Proware EP-2123J-S3S3 - page 8

    SAS to SAS /SA T A II JB OD Sub syst em 8 User Manual 1.4.2 Rear View Single JBOD Contr oller Dual JBOD Controll er ...

  • Proware EP-2123J-S3S3 - page 9

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 9 1.4.3 JBOD Controller Module The EPICa JBOD subsystem includes a single or dual 3Gb SAS-to-SAS /SATA II JBOD Controller Modul e. JBOD Controller Module ...

  • Proware EP-2123J-S3S3 - page 10

    SAS to SAS /SA T A II JB OD Sub syst em 10 User Manual 1.4.3.1 JBOD Controller Panel Part Description SAS In Port Use to connect to SAS HBA or t o RAID subsystem’s SAS Expansion Port. SAS Expansion Port Use to connect to the SAS In Po rt of another JBOD subsystem. RS-232 Port Use to upgrade the firmware of the JBOD controller. Connect the RJ11-to ...

  • Proware EP-2123J-S3S3 - page 11

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 11 1.5 Power Supply Fan Mo dule (PSFM) The EPICa JBOD subsystem contains two 400W Power Supply / Fan Modules . All PSFMs are insert ed into the rear of the chassis. 1.5.1 PSFM Panel The panel of the Power Supply/Fan Modu le contains: the Power On /Off Switch, the AC Inlet Plu g, and a Power On/Fail ...

  • Proware EP-2123J-S3S3 - page 12

    SAS to SAS /SA T A II JB OD Sub syst em 12 User Manual NOTE: Each PSFM has one Power Su pply and one Fan. PSFM 1 has Power#1 and Fan#1 , and PSFM 2 has P ower#2 and Fan#2. When the Power Supply of a PSFM fails, the PSFM need n ot be removed from the slot if replacement is not yet available. The fan will still work and provide ne cessary ai rflow in ...

  • Proware EP-2123J-S3S3 - page 13

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 13 1.6 LCD Display Panel 1.6.1 LCD Panel LED Parts Function Power LED Green indicates power is ON. Power Fail LED If one of the redundant power supply unit fail s, this LED will turn to RED and al arm will soun d. Fan Fail LED Turn RED when fan 1 or 2 fails, or speed is lower than 50 0 RPM. Over Te ...

  • Proware EP-2123J-S3S3 - page 14

    SAS to SAS /SA T A II JB OD Sub syst em 14 User Manual 1.6.2 LCD Panel Function Buttons Parts Function Up and Down Arrow buttons Use the Up or Down arrow ke ys to go through the infor mation on the LCD screen. This is also used to move between e ach menu. Select button This is used to enter the option you have selected. Exit button EXIT Press this ...

  • Proware EP-2123J-S3S3 - page 15

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 15 1.7 Drive Carrier Module The Drive Carrier Module houses a 3.5 inch hard disk drive. It is designed for maximum airflow and incorporates a ca rrier locking mechanism to prevent unauthorized access to the HDD. 1.7.1 Disk Drive Status Indicators Part Function Disk Activity Indicator This LED will ...

  • Proware EP-2123J-S3S3 - page 16

    SAS to SAS /SA T A II JB OD Sub syst em 16 User Manual 1.7.2 Drive Carrier Lock Indicator Every Drive Ca rrier is lockable and is fitted with a lock indicator to indicate whether or not the carrier is locked into the chassis or not. Each carrier is also fitted with an ergonomic ha ndle for easy carrier removal. When the Lock Groove is vertical, th ...

  • Proware EP-2123J-S3S3 - page 17

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 17 Chapter 2 Installation of JBOD Subsystem 2.1 Powering On 1. Plug in the power cords into the AC Power Input Socket located at the rear of the subsystem. NOTE: The subsystem is equipped with r edundant, full range power supplies with PFC (power factor correction). The system will automatically se ...

  • Proware EP-2123J-S3S3 - page 18

    SAS to SAS /SA T A II JB OD Sub syst em 18 User Manual 2.2 Disk Drive Installation This section describes the physical locat i ons of the hard drives supported by the subsystem and give instructions on in stalling a hard drive. The subsystem supports hot-swapping allowing y ou to install or replac e a hard drive while th e subsystem is running. 2.2 ...

  • Proware EP-2123J-S3S3 - page 19

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 19 4. Place the hard drive in the disk tra y. Turn the disk tray up side down. Align the four screw holes of the SAS disk drive in t h e f o u r H o l e A o f t h e d i s k t r a y . T o secure the disk drive into the disk tray, ti ghten four screws on these hol es of the disk tray. Note in the pic ...

  • Proware EP-2123J-S3S3 - page 20

    SAS to SAS /SA T A II JB OD Sub syst em 20 User Manual 5. Slide the tray into a slot. 6. Press the lever in until you hear t he latch click into place. The HDD Fa ult LED will turn green when the subsyste m is powered on and HDD is good. 7. If necessary, lock the Disk Tray by turning the Lock Groove. ...

  • Proware EP-2123J-S3S3 - page 21

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 21 2.2.2 Installing a SATA Disk Driv e (Dual JBOD Controller Mode) in a Disk Tray 1. Remove an empty disk tray from the subsyste m. 2. Prepare the dongle board and two screws. 3. Place the dongle board i n the disk tray. Turn the tray upside down. Align the two screw hole of the dongle board in the ...

  • Proware EP-2123J-S3S3 - page 22

    SAS to SAS /SA T A II JB OD Sub syst em 22 User Manual NOTE: All the disk tray holes are labelled accordingl y. 4. Place the SATA disk drive into the disk tray. Slide the disk dri ve towards the dongle board. Tray Hole D ...

  • Proware EP-2123J-S3S3 - page 23

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 23 5. Turn the disk tray upside down. Align the four screw holes of the SA TA disk drive in the four Hole C of th e disk tray . To secure the disk drive into the disk tray, tighten four screws on these holes of the disk tray. Note in the picture below where the screws sho uld be pl aced in the disk ...

  • Proware EP-2123J-S3S3 - page 24

    SAS to SAS /SA T A II JB OD Sub syst em 24 User Manual 2.3 Connecting the JBOD Subs ystem 2.3.1 Connecting to SAS HBA The Enclosure supports SAS inte rfa ce which provides fa st 300MB data tra nsfer rate using SAS phy . The pa ckage comes with one SAS cable for sin gle JBOD controller module, or two SAS cables for redu ndant JBOD controller modules ...

  • Proware EP-2123J-S3S3 - page 25

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 25 Chapter 3 Maintenance 3.1 Upgrading Firmware Upgrading Firmware Trough Terminal NOTE: It is important to st op I/O access to JBOD su bsystem during firmware upgrade. NOTE: Upgrading the firmware must be done from Master JBOD Controller if the JBOD Subs ystem has redundant JBOD Cont rollers. 1. P ...

  • Proware EP-2123J-S3S3 - page 26

    SAS to SAS /SA T A II JB OD Sub syst em 26 User Manual location. Select “1K Xmodem” Prot ocol to send firmware file ( Only need about 15 seconds to finish sending firmware file. If n ot, please repeat steps E and F again ). NOTE: If the JBOD Subsystem has r edundant JBOD Controllers, remove the serial cable (RJ11 to DB 9) from RS232 Port of JB ...

  • Proware EP-2123J-S3S3 - page 27

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 27 3.2 Replacing JBOD Subsystem Components 3.2.1 Replacing JBOD Controller Module When replacing a failed JBOD Controller Module, please follow these steps: 1. Loosen the thumbscrews on the sides of the JBOD Controller Module drawer. 2. Use the Controller han dle to pull out the defect ive JBOD Con ...

  • Proware EP-2123J-S3S3 - page 28

    SAS to SAS /SA T A II JB OD Sub syst em 28 User Manual 3.2.1.1 Replacing Controller Module with Plate Cover When replacing a failed JBOD Controller Modu le with Plate Cover, please follow these steps: 1. Loosen thumbscrews of the failed JBOD Contr oller Module drawer. 2. Use the Controller Module h andle to remove th e failed JBOD Controller Module ...

  • Proware EP-2123J-S3S3 - page 29

    SAS to SAS /SA T A II JBO D Subsy stem User Manual 29 3.2.2 Replacing Power Supply Fan Module When replacing a failed power su pply fan module (P SFM), please follow these steps: 1. Turn off the Power On/O ff Switch of the faile d PSFM. 2. Disconnect the power c ord from the AC Inle t Plug of PSFM. 3. Loosen thumbscrews of the PSFM. 4. Use the hand ...

  • Proware EP-2123J-S3S3 - page 30

    SAS to SAS /SA T A II JB OD Sub syst em 30 User Manual 3.2.2.1 Replacing Power Supply Fan Module with Plate Cover When replacing a failed power supply fan mo d ule (PSFM) with Plate Cover, please follow these steps: 1. Turn off the Power On/O ff Switch of the faile d PSFM. 2. Disconnect the power c ord from the AC Inle t Plug of PSFM. 3. Loosen thu ...

Fabbricante Proware Categoria Server

I documenti che otteniamo dal fabbricante del dispositivoProware EP-2123J-S3S3 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Proware
- manuali per l’uso EP-2123J-S3S3
- schede prodotto Proware
- opuscoli
- o etichette energetiche Proware EP-2123J-S3S3
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Proware EP-2123J-S3S3.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Proware EP-2123J-S3S3, manuali di manutenzione, brevi manuali o manuali utente Proware EP-2123J-S3S3. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Proware EP-2123J-S3S3.

Manuali per l’uso simili

Manuale completo del dispositivo Proware EP-2123J-S3S3, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Proware EP-2123J-S3S3 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Proware EP-2123J-S3S3.

Il manuale per l’uso completo Proware, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Proware EP-2123J-S3S3 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Proware EP-2123J-S3S3, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Proware EP-2123J-S3S3 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Proware EP-2123J-S3S3 - che ci dovrebbe aiutare nei primi passi durante l'uso Proware EP-2123J-S3S3
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Proware EP-2123J-S3S3
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Proware EP-2123J-S3S3 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Proware EP-2123J-S3S3?

Utilizza il modulo sottostante

Se non hai risolto il problema con Proware EP-2123J-S3S3 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Proware EP-2123J-S3S3 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)