Italiano dropdown-ico

Manuale per l’uso CMA Dishmachines CMA-44

25 pagine 1.61 mb
Scarica

Vai alla pagina of 25

Summary
  • CMA Dishmachines CMA-44 - page 1

    www.cmadishmachines.com ...

  • CMA Dishmachines CMA-44 - page 2

    Table of Contents CMA-44 1. SPECIFICATIONS ................................................................................................. 2 1.1. CMA-44 .......................................................................................................................................... 2 2. GETTING STARTED ................................... ...

  • CMA Dishmachines CMA-44 - page 3

    1. S pecifications 1.1. CMA-44 WATER CONSUMPTION PER RACK (FINAL RINSE) .8 GAL. .94 GAL. PER HOUR (FINAL RINSE) 192 GAL. 192 GAL. CONVEYOR SPEED FEET PER MINUTE 6.75 5.7 OPERATING CAPACITY RACKS PER HOUR (NSF rated) 242 205 OPERATING TEMPERATURE WASH (MIN) 140° - 150° F 150° - 160° F FINAL RINSE (MIN) 140° - 150° F 180° - 195° F WATER REQUI ...

  • CMA Dishmachines CMA-44 - page 4

    Getting Started 2. Getting S t arted 2.1. Introduction to CMA-44 The CMA-44 is designed to give maximum cleaning in 44 inches. It represents the cleaning power of machines twice i ts length. The curtains incorporate d in the machine minimize tra nsfer from tank to tank during the wash and sanitizing pro c edures. Energy costs for running the CMA-4 ...

  • CMA Dishmachines CMA-44 - page 5

    Getting Started 2.2. Receiving and Installation When you receive your new CMA-44, complete the assembly by installing the scrap tray assembly with its overflow chut e, the two wrapper shi elds and the curtain ro ds, which are shipped inside the machine. After the box has b een remo ved from the machine, remove the left and right stainless steel wra ...

  • CMA Dishmachines CMA-44 - page 6

    Getting Started 2.3. Receiving and Installation (Old Models) When you receive your new CMA-44, complete the assembly by installing the scrap tray assembly with its overflow chut e, the two wrapper shi elds and the curtain ro ds, which are shipped inside the machine. After the box has b een remo ved from the machine, remove the left and right stainl ...

  • CMA Dishmachines CMA-44 - page 7

    Getting Started 2.3.1. Electrical * A 3-phase 208-240 volt AC, 60 Hz dedicated circuit should be used to supply electri cal energy to the CMA-44 dishwasher (see specification sheet page 2 ). Connect the wire that has the highest voltage (stinger lead) to the main contactor’s po wer terminal L2 . Power lead wires (L1, L2 and L3) used for the CMA-4 ...

  • CMA Dishmachines CMA-44 - page 8

    Getting Started P/N 13505.12 205 RACKS ( CMA-44H ) 242 RACKS ( CMA-44L ) P/N 13505.10 OLD Models Figure 2.3.3 b 4. On a 3-phase machine the water pump motors are al so 3-phase and, dependin g on which terminal each phase is co nne cted to, the motor can rotate in either direction. Check the direction of rotation by removing the dust cap on the ba c ...

  • CMA Dishmachines CMA-44 - page 9

    Getting Started 2.3.4. Scrap Tra y Assembl y and Overflow Chute Installation The scrap tray assembly and overflow ch ute, whi ch came packaged inside the machine, can easily be installed by executing the foll owing steps: Figure 2.3.4 below illustrates the assembly as it would appear for a Left-to-R ight machine – a Right-to- Left machine would s ...

  • CMA Dishmachines CMA-44 - page 10

    Getting Started 2.3.5. Pump Impeller Note Figure 2.2.5 Installation: When installing the water pump imp eller the Nylon Lock Nut indicated by the arro w in Fig ure 2.2.5 must be in place to prevent the impeller from spinn ing off of the shaft and damaging the motor. Removal: The Nylon Lock Nut indicated by the arrow i n Figure 2.2.5 must be removed ...

  • CMA Dishmachines CMA-44 - page 11

    Getting Started 2.3.6. Optional Hood Adapter (Set of Two) An optional Hood Adapter set (P/N 13901.82) i s available. The di mensions for proper installation are given belo w. 53-½" 9-½" 65" Leg Adj 66” Vents Measure 4” x 16” MODEL CMA-44 Installatio n & Operation Manual Rev. 2 .15 10/18/07 Page 10 ...

  • CMA Dishmachines CMA-44 - page 12

    Getting Started 2.3.7. Optional Freestanding Scrap Trap and Adaptor Kit The optional Freestandi ng Scrap Trap (P/N 0156 0.00) and Adaptor Kit (P/N 13512.00) are available for i nstallations where the space is insufficient t o accommodate the standard side -mounted scrap trap or wh ere drain acce ss is easier by locating the scrap trap some distance ...

  • CMA Dishmachines CMA-44 - page 13

    Getting Started 2.3.8. Field Installed Accessories Installation of the accessory chemi cal pumps must be pe rformed by qualified personnel. 2.3.8.1. Chemical Dispensers 1. Chec kvalves should be installed dire ctly at the mixing cham be r coupling. There are two 1/8” FPT mounting hole s provided, which will p ositio n the checkvalves parallel to ...

  • CMA Dishmachines CMA-44 - page 14

    Getting Started 2.4. Safety Tips for the CMA-44 DA NGE R: Always turn off the circuit breaker at the wall when working on this dishmachine. Even with the machine’s po wer switch off there is a live connection coming to the switch, so turn off the circuit breaker a s well. CAUTION: Do not get in the path of the conveyor rocker arm or the conveyor? ...

  • CMA Dishmachines CMA-44 - page 15

    Operation 3. Operation 3.1. Initial Setup 3.1.1. Auto Fill Timer/ Auto Re- Fill Timer Both timers for the CMA-44 are set at the factory. When the po wer button is activated, the machine should fill until it begi ns to overflow into the scrap tray, at which point it should stop filling. If necessary, adjust the time set on the Auto Fill Timer to all ...

  • CMA Dishmachines CMA-44 - page 16

    Operation 3.2. Beginning Operation To run the dishmachine, perform the following step s: 1. Close both d r ains (valve h andles in vertical position). CLOSE CLOSE 2. Turn on the p ower to the dishmachine. T he machine will begin its (adjustable) timed auto-fill. The float when sen sing adequate water level energizes an ice cube relay, which will al ...

  • CMA Dishmachines CMA-44 - page 17

    Operation 5. At the end of the shift and after heavy period s of accumulation, clean the three strainer trays inside the machine. Also, at the end of each shift, remove and clean the six spray arms. Then reinstall them into the machine. Also, when water becomes heavily soiled, drain the ta nks and refill the machine. STRAINER TRA Y SP R AY AR M 6. ...

  • CMA Dishmachines CMA-44 - page 18

    Operation pressure regulator is adjusted to 20-PSI. This allows 0.8 (CMA-4 4L), or 0.94 (CMA-44H) gallons of water to enter the machine each time a ra ck is washed. It is recommended that the 5-1/2% c hemical solution be standardized to allow uniform dispensing of the sanitizing sol ution into the flow of rinse water as the machine operates. At thi ...

  • CMA Dishmachines CMA-44 - page 19

    Operation 7. Place a rack into the machine and observe the spray pattern of the pre-wa sh, the wash, and the final rinse. a. Check the titration of the wash tank at this point. b. While the rack is in the fin al rinse, chec k for 50 PPM resid ual chlorine in the final rinse. c. Observe the final rinse vacuum breaker for leaks. 8. Run a stemware or ...

  • CMA Dishmachines CMA-44 - page 20

    Operation 3.4. Quick service guide MODEL CMA-44 Installatio n & Operation Manual Rev. 2 .15 10/18/07 Page 19 MODELS: CMA 44/ 66 CONVEYOR (S) TECHNICA L ISSUE CAUSE SOLUTION Continuously cyc les Manual/auto switch in MANUAL mode or faulty Turn switch to AUTO position or replace Conveyer t imer faulty Replace timer, P/N 13418. 85 Faulty tilt micr ...

  • CMA Dishmachines CMA-44 - page 21

    Operation 3.5. Trouble Shooting PROBLEM LIKELY CAUSE SOLUTION Pre-wash/power wash motor inoperative Bad motor or capacitor Faulty contactor Replace defect ive motor Replace contactor Fuse is burned out Replace fuse Table limit switch Remove dish rack at switch Defective door reed switch Replace reed switch Defective start r eed switch Replace reed ...

  • CMA Dishmachines CMA-44 - page 22

    Customer Notice 4. CMA-44 Customer Notice MODEL CMA-44 Installatio n & Operation Manual Rev. 2 .15 10/18/07 Page 21 ...

  • CMA Dishmachines CMA-44 - page 23

    Customer Notice TIPS TO SAVE A SERVICE CHARGE If the Lessee of this equipment initiates a service call and it is sub sequently determined that the problem does not relate to part failure or out of chemical s, there will be a mini mum service ch arge for a service person to respond. It is recommended that you check the foll owing items before initia ...

  • CMA Dishmachines CMA-44 - page 24

    Electrical Diagrams 5. Electrical Diagram MODEL CMA-44 Installatio n & Operation Manual Rev. 2 .15 10/18/07 Page 23 ...

  • CMA Dishmachines CMA-44 - page 25

    Electrical Diagrams 6. Electrical Diagram (Old Models) MODEL CMA-44 Installatio n & Operation Manual Rev. 2 .15 10/18/07 Page 24 ...

Fabbricante CMA Dishmachines Categoria Dishwasher

I documenti che otteniamo dal fabbricante del dispositivoCMA Dishmachines CMA-44 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici CMA Dishmachines
- manuali per l’uso CMA-44
- schede prodotto CMA Dishmachines
- opuscoli
- o etichette energetiche CMA Dishmachines CMA-44
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso CMA Dishmachines CMA-44.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione CMA Dishmachines CMA-44, manuali di manutenzione, brevi manuali o manuali utente CMA Dishmachines CMA-44. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto CMA Dishmachines CMA-44.

Manuali per l’uso simili

Manuale completo del dispositivo CMA Dishmachines CMA-44, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare CMA Dishmachines CMA-44 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti CMA Dishmachines CMA-44.

Il manuale per l’uso completo CMA Dishmachines, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale CMA Dishmachines CMA-44 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice CMA Dishmachines CMA-44, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per CMA Dishmachines CMA-44 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo CMA Dishmachines CMA-44 - che ci dovrebbe aiutare nei primi passi durante l'uso CMA Dishmachines CMA-44
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del CMA Dishmachines CMA-44
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio CMA Dishmachines CMA-44 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su CMA Dishmachines CMA-44?

Utilizza il modulo sottostante

Se non hai risolto il problema con CMA Dishmachines CMA-44 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con CMA Dishmachines CMA-44 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)