Italiano dropdown-ico

Manuale per l’uso AT&T 206 and 410

33 pagine 0.42 mb
Scarica

Vai alla pagina of 33

Summary
  • AT&T 206 and 410 - page 1

    AT&T MERLIN ® COMMUNICATIONS SYSTEM INSTALLATION GUIDE: MODELS 206 AND 410 ...

  • AT&T 206 and 410 - page 2

    Table of Contents Pag e Introduction Getting Started Installing the Control Unit Position the Control Unit Set the Control Unit Switches Connect the Control Unit to the AC Outlet Prepare the Network Interface Test the Outside Lines Connect the Control Unit to the Network Interface Voice Terminal Wiring Jack Field Connection Direct Connection Connec ...

  • AT&T 206 and 410 - page 3

    Introduction This installation guide tells you how to install and test your MERLIN ® com- munications system, Model 206 or 410. It leads you step by step through system installation, from a pre-installation checklist to system tests. You should per- form the steps in the order in which they are presented because many of the earlier steps prepare t ...

  • AT&T 206 and 410 - page 4

    Getting Started This guide assumes the tasks on the following list have been completed. Review the list carefully. If you have not completed the tasks on the list, do so now. ● Make sure the necessary wiring is in place. You must have a network interface that links your MERLIN system to the local telephone company’s lines. A telephone company r ...

  • AT&T 206 and 410 - page 5

    ● ● ● ● Check the items in your shipment against your copy of the order form. Become familiar with your MERLIN system. Make sure the items and quantities agree. Save the instructions packed Review the figure of a simple MERLIN system configuration, opposite with components; you may need to refer to them later. And keep the pack- page, and n ...

  • AT&T 206 and 410 - page 6

    10 AC outlet Line cord Network interface 9 8 Control unit Modular jumper cord Jack field Voice terminal Modular voice terminal cord Modular wall jack Building wiring 1 2 3 7 6 5 4 5 ...

  • AT&T 206 and 410 - page 7

    Installing the Control Unit Installation procedures are basically the same for both Model 206 and Model 410. The instructions point out only those differences between the models that affect installation. POSITION THE CONTROL UNIT If you plan to wall mount your control unit, follow the instructions in the booklet titled CIB 3029 (for Model 206) or C ...

  • AT&T 206 and 410 - page 8

    CONNECT THE CONTROL UNIT TO THE AC OUTLET The outlet should not be switch-controlled. Plugging your control unit into a switch-controlled outlet invites accidental disconnection of the system. 1 2 ● ● Find the power cord attached to the control unit and plug it into the ac outlet. The green power light on the control unit goes on. The red warni ...

  • AT&T 206 and 410 - page 9

    PREPARE THE NETWORK INTERFACE Your local telephone company should have installed a network interface with 1-line jacks (RJ11-type) or 2-line jacks (RJ14-type) for connecting your MERLIN system to your outside telephone lines. The drawing, right, shows the two types of network interface and the 2-line adapter (267C) for the 2-line network inter- fac ...

  • AT&T 206 and 410 - page 10

    TEST THE OUTSIDE LINES This step is optional, but if you have a basic Touch-Tone or rotary telephone with a modular plug, you should test your outside line connections now. It can save time and frustration later. NOTE: A MERLIN system voice terminal will not work for this test. 1 2 2 Network interface 1 Take a basic Touch-Tone or rotary telephone w ...

  • AT&T 206 and 410 - page 11

    CONNECT THE CONTROL UNIT TO THE NETWORK INTERFACE When you are assigning outside lines to the outside line jacks on the control unit, keep in mind that the MERLIN system automatically selects lines in alphabetical order for your outgoing calls unless you have a Feature Package and have programmed a different line-selection sequence. Let’s say, fo ...

  • AT&T 206 and 410 - page 12

    1 2 Model 206 control unit Model 410 control unit Outside line jacks Line cord labels 6 3 A 4 Network interface 5 11 ...

  • AT&T 206 and 410 - page 13

    Voice Terminal Wiring The intercom number for each voice terminal in your MERLIN system is the same as the number of the voice terminal jack on the control unit to which that voice terminal is connected. On a Model 206 control unit, the voice terminal jacks are numbered 0 through 5. On a Model 410 control unit, the voice terminal jacks are numbered ...

  • AT&T 206 and 410 - page 14

    2 1 4 3 8 5 10 13 ...

  • AT&T 206 and 410 - page 15

    DIRECT CONNECTION To connect your voice terminal locations directly to the control unit, do this: 1 4 2 3 10 1 2 3 4 5 6 In the system directory, fill in the voice terminal location you have selected for each intercom number. Beginning with the pair of labels marked 0 for Model 206 or 10 for Model 410, label each cord at both ends with matching lab ...

  • AT&T 206 and 410 - page 16

    Connecting the Voice Terminals ● ● ● ● ● Each voice terminal has the following components: Voice terminal body Handset Coiled handset cord Modular voice terminal cord Desk stand and/or wall mount Voice terminal Handset 3 LINE PREPARE THE VOICE TERMINALS Prepare the voice terminals as follows: 1 2 3 4 5 Assemble each voice terminal and att ...

  • AT&T 206 and 410 - page 17

    CONNECT EACH VOICE TERMINAL TO THE SYSTEM Place the voice terminal in its designated location. Plug the voice terminal into the system in one of the following ways: 1 2 1 2 If You Have And Do This a direct connection the connection re- Go on to step 3. You from the voice ter- quires only a single have already con- minal to the control modular voice ...

  • AT&T 206 and 410 - page 18

    3 Slide the T/P switch to T and hold it there. All the red and green lights on the voice terminal begin to flash, and a tone sounds. If the lights do not flash: Do This If The n A. Check the green the green power light go to B. power light on the is on control unit. the green power light unplug the power is off cord from the ac outlet and plug it i ...

  • AT&T 206 and 410 - page 19

    1 2 TEST EACH VOICE TERMINAL FOR A DIAL TONE Lift the handset. The green light goes on next to the shining red light, and you hear a dial tone. Press one or more of the dial pad buttons. The dial tone stops. If your system does not respond as described, make a note of it and refer to the Troubleshooting Table, page 26, after you’ve completed the ...

  • AT&T 206 and 410 - page 20

    Installing Accessories Once you have installed your MERLIN system, you may want to add ac- cessories to enhance your system’s capabilities. CARTRIDGES Cartridges provide the software and interfaces that make it possible for you to use many of the MERLIN system features and accessories. Without any car- tridges, you will have Standard Features, wh ...

  • AT&T 206 and 410 - page 21

    OTHER ACCESSORIES You can enhance your system by adding accessory equipment. Accessories such as Extra Alert horns, Loudspeaker Paging, and Power Failure Transfer telephones require additional cartridges. General Purpose Adapters for your voice terminals allow you to connect modems, autodialers, cordless phones, and other extension phones. You can ...

  • AT&T 206 and 410 - page 22

    System Tests Now that your system equipment is in place, you need to test it to make sure it’s operating properly. The following tests will help you determine if you have installed your system correctly and if all your system components are working. If these tests reveal any problems, see the Troubleshooting Table, page 26. 1 PLACE AN OUTSIDE CAL ...

  • AT&T 206 and 410 - page 23

    PLACE AN INTERCOM CALL Make this test call from one voice terminal to another voice terminal in your system. Have someone available to answer the intercom call. 1 2 3 4 5 6 From a voice terminal, touch the fifth button down in the leftmost row of buttons (Intercom-Ring) without lifting the handset. The red light next to the button goes on. Lift the ...

  • AT&T 206 and 410 - page 24

    What’s Next? Now that your MERLIN system is installed, you need to program it to meet your business needs. If you have standard features, refer to the Standard Features User’s Guide: Models 206, 410 and 820. If you have a Feature Package, refer to the administration manual that comes with the Feature Package to learn how to customize the system ...

  • AT&T 206 and 410 - page 25

    System Changes Your MERLIN communications system is designed so that you can make system changes quickly and easily. You can increase your system’s capacity simply by adding outside lines and voice terminals to a maximum of 2 lines and 6 voice terminals for Model 206, and 4 lines and 10 voice terminals for Model 410. You can increase the system? ...

  • AT&T 206 and 410 - page 26

    UPGRADING FROM MODEL 206 TO MODEL 410 If your needs expand beyond the capacity of your Model 206 system, you can easily install a Model 410 system in its place. You can reuse the cartridges, voice terminals and accessories that came with your Model 206. 1 2 3 4 5 6 7 Have your local telephone company add outside line(s) and network interface jack(s ...

  • AT&T 206 and 410 - page 27

    Troubleshooting Refer to the following table if you have trouble with your MERLIN system. Identify the symptom in the “Trouble” column of the table, and perform the recom- mended steps to isolate and correct the problem. If you are unable to identify a particular problem, perform the general test on page 29 before calling your equip- ment suppl ...

  • AT&T 206 and 410 - page 28

    TROUBLESHOOTING TABLE (CONTINUED) Trouble Possible Cause Do this If Then You have difficulty Faulty network inter- 5. Replace the network inter- the trouble still appears on the your outside telephone lines are placing outside calls face line adapter face line adapter with another basic telephone faulty. Report the trouble to your from more than on ...

  • AT&T 206 and 410 - page 29

    TROUBLESHOOTING TABLE (CONTINUED) Trouble There is trouble with voice terminal lights, speaker, or ringing. (continued) A voice terminal rings constantly. Possible Cause Do this If Control unit Cord connections Inadequate power supply to the control unit 3. 4. 5. 2. Go to the control unit and the trouble still occurs locate the intercom jacks for b ...

  • AT&T 206 and 410 - page 30

    TROUBLESHOOTING TABLE (CONTINUED) Trouble Possible Cause Do this If Then All voice terminals Faulty power outlet 3. Test the outlet by plugging in the appliance doesn’t work the outlet is faulty or controlled by a have no lights and an appliance such as a lamp wall switch. no dial tone. or a radio. (continued) the appliance works the control unit ...

  • AT&T 206 and 410 - page 31

    Appendix A: Interference Information According to Federal Communications Commission (FCC) Rules, you need to know that: ● This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this installation guide, may cause interference to radio communications. ● The equipment has been teste ...

  • AT&T 206 and 410 - page 32

    Index AC Outlet, 4, 5, 6, 7 Accessories, 19, 20 Autodialer, 20 Extra Alert, 19, 20 Hands-Free Unit, 20 Headset, 20 Voice Terminal Power Supply, 20 Administering the MERLIN System, 2, 6, 23, 24 Airborne Contamination, 4 Building Wiring, 3, 4, 5, 12, 25 Call Transfer, 19 Cartridges, 4, 19, 24, 25 Conference Calling, 19 Control Unit, 2 - 7, 10 - 15, 1 ...

  • AT&T 206 and 410 - page 33

    AT&T Issue 5 MERLIN is a registered trademark of AT&T © Copyright 1986 AT&T. Printed in U.S.A. 518-600-000 IS July 1986 ...

Fabbricante AT&T Categoria Telephone

I documenti che otteniamo dal fabbricante del dispositivoAT&T 206 and 410 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici AT&T
- manuali per l’uso 206 and 410
- schede prodotto AT&T
- opuscoli
- o etichette energetiche AT&T 206 and 410
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso AT&T 206 and 410.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione AT&T 206 and 410, manuali di manutenzione, brevi manuali o manuali utente AT&T 206 and 410. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto AT&T 206 and 410.

Manuali per l’uso simili

Manuale completo del dispositivo AT&T 206 and 410, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare AT&T 206 and 410 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti AT&T 206 and 410.

Il manuale per l’uso completo AT&T, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale AT&T 206 and 410 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice AT&T 206 and 410, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per AT&T 206 and 410 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo AT&T 206 and 410 - che ci dovrebbe aiutare nei primi passi durante l'uso AT&T 206 and 410
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del AT&T 206 and 410
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio AT&T 206 and 410 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su AT&T 206 and 410?

Utilizza il modulo sottostante

Se non hai risolto il problema con AT&T 206 and 410 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con AT&T 206 and 410 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)