Italiano dropdown-ico

Manuale per l’uso Peavey Nitrobass

36 pagine 4.27 mb
Scarica

Vai alla pagina of 36

Summary
  • Peavey Nitrobass - page 1

    NITROBASS ™ Professional Bass Amplifier NITROBASS ™ Professional Bass Amplifier O PERA TING G UIDE ...

  • Peavey Nitrobass - page 2

    2 Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the prod ...

  • Peavey Nitrobass - page 3

    NITROBASS ™ PROFESSIONAL BASS AMPLIFIER Congratulations on your purchase of the Peavey NitroBass ™ . The NitroBass includes an easy-to- use, three-band active EQ with shiftable mid-range control and a contour control (for that smiley- face EQ curve). These tone controls are so versatile you should be able to quickly dial up your own sound. Also ...

  • Peavey Nitrobass - page 4

    AC POWER FEA TURES: 1. REMOV ABLE AC POWER CORD This receptacle is for the IEC line cord (included), which provides AC power to the unit. Connect the line cord to this connector and to a properly grounded AC supply . Damage to the equipment may occur if an improper line voltage is used. (See voltage marking on unit.) Never remove or cut the ground ...

  • Peavey Nitrobass - page 5

    NOTE: THE FUSE SHOULD ONL Y BE REPLACED WHEN THE REMOV ABLE POWER CORD HAS BEEN DISCONNECTED FROM ITS CHASSIS RECEPT ACLE (1). 5. POWER/ST A TUS LED Located on front panel this LED illuminates green when the Power Switch is in the “ON” position and AC power is supplied. During normal operation the LED also acts as a DDT indicator . The LED illu ...

  • Peavey Nitrobass - page 6

    13. MID CONTROL An active tone control (peak/notch, ±15 dB) that varies the midrange boost or cut. 14. MID SHIFT CONTROL Selects the frequency band (200 — 2 kHz) that the mid control cuts or boosts. 15. HIGH CONTROL An active tone control (shelving type, ±15 dB) that varies the high frequency boost or cut. 16. VOLUME CONTROL Controls the overal ...

  • Peavey Nitrobass - page 7

    7 REAR P ANEL FEA TURES: 27. POWER CORD RET AINERS Use the Power Cord Retainers to wrap and store your cable while storing or transporting your NitroBass. It is best to disconnect the cord from the unit before wrapping. 28. SPEAKER OUTPUT JACKS These two 1/4" jacks provide the powered signal from the amplifier . Each connector is electrically ...

  • Peavey Nitrobass - page 8

    Input Tuner Send Instrument Level Buffer -10 db Pad In/Out -10 db Pad Gain Bright Contour Infrasonic Filter Shelving EQ Low Shelf (Bass) +/- 15 dB High Shelf (Treble) +/- 15 dB Buffer Effects Send Effects Loop -10 dB, 0, 315 VRMS Effects Return Effects Loop Footswitch Switch Logic Buffer Volume CW Buffer Line Level 1 VRMS, 0dB Line Level 1 VRMS, 0d ...

  • Peavey Nitrobass - page 9

    9 Rock Setting Out Set to appropriate level for instrument used Set as necessary NOTE: “DDT should be utilized for maximum speaker protection” Slap Setting In Set to appropriate level for instrument used Set as necessary NOTE: “DDT should be utilized for maximum speaker protection” Blues/ Country Setting Out Set to appropriate level for ins ...

  • Peavey Nitrobass - page 10

    10 SYSTEM SPECIFICA TIONS: Mains Fuse = 8 amps Mains V oltage = 120 V AC 60 Hz Power Consumption = 350 watts Hum and noise: T ypically greater than -89 dB unweighted with controls set as follows… Pad = Passive Bright = Normal Pre gain = 5 Contour = 0 L ow = 0 Mid = 0 Mid Shift = 1kHz High = 0 V olume = 5 POWER AMPLIFIER SECTION: PROTECTION: Elect ...

  • Peavey Nitrobass - page 11

    NITROBASS ™ Amplificador profesional para bajo Felicitaciones por tu compra del NitroBass ™ de Peavey . El NitroBass incluye un ecualizador activo de tres bandas con control de cambio de medios y control de silueta que es fácil de usar (para lograr esa curva de ecualización de cara feliz). Estos controles de tono son tan versátiles que podr? ...

  • Peavey Nitrobass - page 12

    CARACTERÍSTICAS DE PODER CA: 1. CABLE DE PODER CA INTERCAMBIABLE Esta entrada es para el cable de línea IEC (incluido), mismo que provee poder CA a la unidad. Conecta el cable de línea a este conector y a un suministro de CA propiamente ater- rizado. El equipo puede dañarse si se usa voltaje de línea inapropiado. (V er marcación de voltaje en ...

  • Peavey Nitrobass - page 13

    NOT A: EL FUSIBLE SÓLO DEBE SER REEMPLAZADO CUANDO EL CABLE DE CORRI- ENTE HA Y A SIDO DESCONECT ADO DE SU RECEPTÁCULO EN EL CHASÍS (1). 5. LED DE EST ADO DE PODER Localizado en el panel frontal este LED se ilumina de verde cuando el interruptor de poder esté en la posición ON y se esté suministrando poder CA. Durante la operación normal el ...

  • Peavey Nitrobass - page 14

    13. CONTROL DE MEDIOS Un control de tono activo (pico/corte, +/- 15 dB) que varía el aumento o corte de las frecuen- cias medias. 14. CONTROL DE MEDIOS Selecciona la banda de frecuencia (200-2kHz) que el control de medios corta o aumenta. 15. CONTROL DE AGUDOS Un control de tono activo (tipo shelving, +/- 15 dB) que varía el aumento o corte de la ...

  • Peavey Nitrobass - page 15

    25. CONECTOR DE SALIDA DE PREMPLI Este conector de 1/4 se usa para enviar la señal del preampli a las entradas externas, como la entrada de un ampli de poder adicional. La señal es post control de volumen. El uso de este conector no cancela la señal del ampli NitroBass (puede notarse alguna diferencia de volumen a causa del cambio de impedancia ...

  • Peavey Nitrobass - page 16

    16 Input Tuner Send Instrument Level Buffer -10 db Pad In/Out -10 db Pad Gain Bright Contour Infrasonic Filter Shelving EQ Low Shelf (Bass) +/- 15 dB High Shelf (Treble) +/- 15 dB Buffer Effects Send Effects Loop -10 dB, 0, 315 VRMS Effects Return Effects Loop Footswitch Switch Logic Buffer Volume CW Buffer Line Level 1 VRMS, 0dB Line Level 1 VRMS, ...

  • Peavey Nitrobass - page 17

    17 Rock Setting Out Set to appropriate level for instrument used Set as necessary NOTE: “DDT should be utilized for maximum speaker protection” Slap Setting In Set to appropriate level for instrument used Set as necessary NOTE: “DDT should be utilized for maximum speaker protection” Blues/ Country Setting Out Set to appropriate level for in ...

  • Peavey Nitrobass - page 18

    18 ESPECIFICACIONES DEL SISTEMA Fusible principal = 8 amps V oltaje = 120 V AC 60 Hz Consumo de poder = 350 wats Hum y ruido: Típicamente mayor que -89 dB sin peso con controles ajustados como sigue: Pad = pasivo Brillante = Normal Pre ganancia = 5 Silueta = 0 Graves = 0 Medios = 0 Cambio de Medios = 1kHz Agudos = 0 V olumen = 5 SECCIÓN DE AMPLIF ...

  • Peavey Nitrobass - page 19

    NITROBASS ™ AMPLIFICA TEUR BASSE Nous vous félicitons pour l’achat de cet amplificateur Peavey NitroBass ™ . Le NitroBass possède un EQ actif 3-bandes avec réglage semi-paramétrique des mediums et un contrôle de contour (pour obtenir aisément la populaire equalisation en V). Ces contrôles de tonalité assurent au NitroBass une versatil ...

  • Peavey Nitrobass - page 20

    CARACTERISTIQUES D’ALIMENT A TION: 1. CONNECTEUR IEC Pour votre securite, un cordon d’alimentation assurant une bonne connexion a la terre est inclus. La connexion a la terre ne doit etre deconnectee en aucune circonstance. Les risques de choc electrique sont considerablement reduits lorsque la masse du chassis est correcte ment reliee a la ter ...

  • Peavey Nitrobass - page 21

    F ACE A V ANT : 5. LED DE ST A TUT ET D’ALIMENT A TION Lorsque le commutateur d'alimentation est sur la position "on", la LED s'illumine en vert. Cette LED joue aussi le rôle d'indicateur DDT . Elle deviendra rouge si la compression DDT se met en action. Si la DDT n'est pas utlisée, la LED s'illuminera en roug ...

  • Peavey Nitrobass - page 22

    14. CONTROLE MID SHIFT Détermine la bande de fréquences sur laquelle agît le contrôle mid. 15. CONTROLE HIGH Contrôle de tonalité actif (± 15 dB) augmentant ou atténuant les fréquences aigues. 16. CONTROLE VOLUME Détermine le volume général de l'amplificateur . Ce contrôle doit être ajusté une fois que le son recherché a été ...

  • Peavey Nitrobass - page 23

    23 P ANNEAU ARRIERE: 27. P A TTES D’ENROULEMENT Utilisez ces pattes pour enrouler votre cordon d'alimentation lors du rangement ou du trans- port de votre amplificateur FireBass 700. Déconnectez le cordon d'alimentation de l'amplifica- teur avant de l'enrouler . 28. SORTIES HP Ces deux prises jacks constituent la sortie de l& ...

  • Peavey Nitrobass - page 24

    Input Tuner Send Instrument Level Buffer -10 db Pad In/Out -10 db Pad Gain Bright Contour Infrasonic Filter Shelving EQ Low Shelf (Bass) +/- 15 dB High Shelf (Treble) +/- 15 dB Buffer Effects Send Effects Loop -10 dB, 0, 315 VRMS Effects Return Effects Loop Footswitch Switch Logic Buffer Volume CW Buffer Line Level 1 VRMS, 0dB Line Level 1 VRMS, 0d ...

  • Peavey Nitrobass - page 25

    25 Rock Setting Out Set to appropriate level for instrument used Set as necessary NOTE: “DDT should be utilized for maximum speaker protection” Slap Setting In Set to appropriate level for instrument used Set as necessary NOTE: “DDT should be utilized for maximum speaker protection” Blues/ Country Setting Out Set to appropriate level for in ...

  • Peavey Nitrobass - page 26

    26 SYSTEM SPECIFICA TIONS: Mains Fuse = 8 amps Mains V oltage = 120 V AC 60 Hz Power Consumption = 350 watts Hum and noise: T ypically greater than -89 dB unweighted with controls set as follows… Pad = Passive Bright = Normal Pre gain = 5 Contour = 0 L ow = 0 Mid = 0 Mid Shift = 1kHz High = 0 V olume = 5 POWER AMPLIFIER SECTION: PROTECTION: Elect ...

  • Peavey Nitrobass - page 27

    NITROBASS ™ PROFESSIONELLER BASS-VERSTÄRKER Wir freuen uns, dass Sie sich für einen Peavey NitroBass ™ -Bassverstärker entschieden haben. Die Klangregelung des NitroBass besteht aus einem aktiven Dreiband-EQ mit parametrischer Mittenregelung sowie einem zusätzlichen Contour-Regler (für die typische EQ-"U-Form") und ist damit so v ...

  • Peavey Nitrobass - page 28

    STROMVERSORGUNG: 1. Separates Netzkabel Diese Buchse ist für das Euro-Netzkabel zur Stromversorgung des Geräts (im Lieferumfang enthalten) vorgesehen. Schließen Sie das Netzkabel ausschließlich an einen korrekt geerde- ten Netzanschluss mit geeigneter Spannung an (siehe Aufschrift Geräterückseite), da das Gerät sonst ernstlichen Schaden nehm ...

  • Peavey Nitrobass - page 29

    ANMERKUNG: ERSETZEN SIE DIE SICHERUNG AUSSCHLIESSLICH BEI GEZOGENEM NETZSTECKER (1). 5. POWER/ST A TUS-LED Auf der Frontplatte befindet sich eine LED, die grün leuchtet, wenn sich der Netzschalter in Position "ON" befindet und dem Gerät Strom zugeführt wird. Im Normalbetrieb fungiert diese LED gleichzeitig als DDT -Anzeige. Bei aktivie ...

  • Peavey Nitrobass - page 30

    13. MID Dieser aktive Klangregler (Peak/Notch-Filter , ± 15 dB) dient der Anhebung bzw . Absenkung der mittleren Frequenzen. 14. MID SHIFT Dieser Regler dient der Einstellung der Eckfrequenz (200 Hz — 2 kHz) für den MID-Regler . 15. HIGH Dieser aktive Klangregler (Shelving-Filter , ± 15 dB) dient der Anhebung bzw . Absenkung der hohen Frequenz ...

  • Peavey Nitrobass - page 31

    25. PREAMP OUT Diese 6,3mm-Klinkenbuchse dient der Überführung des V orverstärker-Signals an ein externes Gerät, z.B. einen zusätzlichen Leistungsverstärker , wobei der Signalabgrif f hinter dem Lautstärkeregler erfolgt. Ist die Buchse belegt, wird das Signal weiterhin an die NitroBass- Endstufe ausgegeben (es ist allerdings möglich, dass S ...

  • Peavey Nitrobass - page 32

    32 Input Tuner Send Instrument Level Buffer -10 db Pad In/Out -10 db Pad Gain Bright Contour Infrasonic Filter Shelving EQ Low Shelf (Bass) +/- 15 dB High Shelf (Treble) +/- 15 dB Buffer Effects Send Effects Loop -10 dB, 0, 315 VRMS Effects Return Effects Loop Footswitch Switch Logic Buffer Volume CW Buffer Line Level 1 VRMS, 0dB Line Level 1 VRMS, ...

  • Peavey Nitrobass - page 33

    33 Rock Setting Out Set to appropriate level for instrument used Set as necessary NOTE: “DDT should be utilized for maximum speaker protection” Slap Setting In Set to appropriate level for instrument used Set as necessary NOTE: “DDT should be utilized for maximum speaker protection” Blues/ Country Setting Out Set to appropriate level for in ...

  • Peavey Nitrobass - page 34

    34 TECHNISCHE DA TEN: Netzsicherung = 8 A Netzspannung = 120 V AC 60 Hz Leistungsaufnahme = 350 W Rauschabstand: typisch > -89 dB, unbewertet, Reglerstellung wie folgt: Pad = Passive Bright = Normal Pre-Gain = 5 Contour = 0 Low = 0 Mid = 0 Mid Shift = 1kHz High = 0 V olume = 5 LEISTUNGSVERSTÄRKER: SCHUTZSCHAL TUNGEN: Elektronischer Eingangsstro ...

  • Peavey Nitrobass - page 35

    35 PEA VEY ELECTRONICS CORPORA TION LIMITED W ARRANTY Effective Date: July 1, 1998 What This W arranty Covers Y our Peavey W arranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada. What This W arranty Does Not Cover The Warranty does not cover: (1) damage caused by accident, misuse, abu ...

  • Peavey Nitrobass - page 36

    IMPOR T ANT SAFETY INSTRUCTIONS W ARNING: When using electric products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . For example, near or in a bathtub, swimming pool, sink, wet bas ...

Fabbricante Peavey Categoria Musical Instrument Amplifier

I documenti che otteniamo dal fabbricante del dispositivoPeavey Nitrobass possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Peavey
- manuali per l’uso Nitrobass
- schede prodotto Peavey
- opuscoli
- o etichette energetiche Peavey Nitrobass
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Peavey Nitrobass.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Peavey Nitrobass, manuali di manutenzione, brevi manuali o manuali utente Peavey Nitrobass. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Peavey Nitrobass.

Manuali per l’uso simili

Manuale completo del dispositivo Peavey Nitrobass, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Peavey Nitrobass dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Peavey Nitrobass.

Il manuale per l’uso completo Peavey, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Peavey Nitrobass - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Peavey Nitrobass, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Peavey Nitrobass che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Peavey Nitrobass - che ci dovrebbe aiutare nei primi passi durante l'uso Peavey Nitrobass
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Peavey Nitrobass
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Peavey Nitrobass in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Peavey Nitrobass?

Utilizza il modulo sottostante

Se non hai risolto il problema con Peavey Nitrobass con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Peavey Nitrobass è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)