Italiano dropdown-ico

Manuale per l’uso White 1500

29 pagine 0.91 mb
Scarica

Vai alla pagina of 29

Summary
  • White 1500 - page 1

    INSTRUCTION MANUAL ITE DIFFERENTIAL MODEL 1500 ...

  • White 1500 - page 2

    IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be folowed, including the following: Read all instructions before using (this sewing machine) DANGER To reduce the risk of electric shock: An apphance should never be left unattended when plugged in. Always unplug this appliance from theelectric ...

  • White 1500 - page 3

    iNTRODUCTION THANK YOU FOR CHOOSING OUR OVERLOCK MACHINE This overlock machine can stitch dependable seams on all kinds of fabric, both light and heavy, including cotton, wool, rayon, tricot, jersey, and knits. You do not need a special table for this portable machine. We suggest that you read this instruction manual carefully before you start to o ...

  • White 1500 - page 4

    QEPNIENTS NAME OF MMN COMPONENTS 3 SETTING UP YOUR MACHINE 4—6 The position of thread pole 4 Spool holders 4 Spool caps 4 Connecting the foot control 5 Controlling sewing speed 5 Safety switch 5 Attaching the waste catcher 6 ACCESSORIES 6 USING THE MACHINE 7 Handwheel 7 Front cover 7 Free arm 7 LOOPER THREADING 8 NEEDLE THREADING 9 TEST SEWING 10 ...

  • White 1500 - page 5

    [MAME OF MAIN COMPONENTS Spool pin Spool holder Handwheel Machine socket Base Lower looper thread tension dial Thread pole Thread guide plate Right needle thread tension dial Left needle thread tension dial Support bed Upper looper thread tension dial —3— Free arm release lever Lower looper ...

  • White 1500 - page 6

    S ETTD4 GUöiJA MACHINE Set your Overlock machine on a sturdy flat surface. [THE POSITION OF THREAD POLE] Pull up thread pole to its highest point before threading. Turn the thread pole so the thread guides come right above the spool pins. Positioning catches 7 [CONE HOLDERS] Both industrial cones and domestic type thread spools can be used on this ...

  • White 1500 - page 7

    [CONNECTING THE FOOT CONTROL] Push toot control plug into the machine socket and then into main socket. Turn on the power switch. This power switch controls both the machine power and sewing light. * This appliance has a polarized plug (one blade widerthari the other). To reduce the risk of electric shock, this plug is intended to fit in a polarize ...

  • White 1500 - page 8

    [ATTACHING THE WASTE CATCHER] The waste catcher catches the cut-off fabnc as you sew, keeping your working area clean. Place the waste catcher between the machine and table. ACCESSORIES Oiler Tweezers Spare upper cutter Needles Machine cover Screwdriver Hexagon wrench key Brush Instruction manual Spool caps Waste catcher —6— ...

  • White 1500 - page 9

    [USING THE MACHINE. I [HANDWHEEL] Always turn handwheel toward you,i.e. the same direction as on a household sewing machine. [FRONTCOVER] To open front cover, slide the hollow to the right as tar as it will go then pull front cover toward you. The front cover won’t close while the tree arm is open. [FREE ARM] Open the tree arm for threading. Open ...

  • White 1500 - page 10

    I LOOPER THREADING Threading must be carried out in the following sequence. I.FIRST Upper looper 2.SECOND Lower looper 3. THIRD Right needle 4.FINALLY Left needle l.Open the front cover and free arm. 2 .Turn the handwheef toward you until, the looper comes to best position for threading. 3 .Pass the upper looper thread and lower looper thread as il ...

  • White 1500 - page 11

    I NEEDLE THREADING 5.Turn the handwheel toward you until needles are fully raised. G.Pass the right and left needle threads as illustrated. Important: The thread must lie correctly between the two discs inside the tension dials. Pass through the needle eyes from front to back as illustrated. 7.Pull out the thread end about 10 cm(4”) long from the ...

  • White 1500 - page 12

    [tRIAL SEWING When the overlock has been threaded for the first time or re-threaded because of thread bre akage during sewing, start sewing in the following manner. Holding the end of threads between your left finger tips, turn the handwheel slowly toward you two or three times and check the thread chain. Place fabnc for trial sewing under the pres ...

  • White 1500 - page 13

    ADJUSTING THREAD TENSIONS Thread tensions will vary according to the type and thickness of both thread and fabric. Adjust the thread tension of the machine accordingly while checking the seam. Thread tension:Turning to a lower number means less tension. Turning to a higher number means more tension. A: Left needle thread tension dial C:Upper looper ...

  • White 1500 - page 14

    It is necessary to adjust the thread tension for the seams shown below. [ADJUSTING THE NEEDLE THREAD TENSIONS] The left needle thread tension is too loose. The right needle thread tension is too loose. [ADJUSTING THE LOOPER THREAD TENSIONS] The lower looper thread is tight and/or the upper looper thread is loose. The upper looper thread is tight an ...

  • White 1500 - page 15

    [MACHINE ADJUSTMENT CHART The best tension for one fabric may not be correct for another. The required tensions depend upon stiffness and thickness of fabric, thread size and type. If necessary, readjust referring to the chart below. labrIcs Threads Needle Stitch length Standard Setting Light-weight Georgette Cotton Organdy Spun HA X 1 2.0-3.5 mm ( ...

  • White 1500 - page 16

    [cHANGING THE THREAD (TYING ON) It is simple to change the thread in the following manner. Cut the thread above the spool pin, and knot ends of old and new threads together. Set the tension dial to “0” and raise the presser foot. Pull the other end of thread until knots come un der the presser foot. For needle threads, pull the other ends of th ...

  • White 1500 - page 17

    [ADJUSTMENT OF STITCH LENGTH There are nine settings which adjustments can be made from 1.0 to 5.0 mm. Most overlock work is done with a standard stitch length setting of 2.5-3.5 mm. Stitch length adjustment knob(lnner dial) Stitches Stitch length Regular seaming 2.O—5.Omm 3.0mm (Standard Setting) Narrow seaming 1.O-2.0mm Rolled edging 1.0 2.0mm ...

  • White 1500 - page 18

    LCuTTING WIDTH 1 The proper cutting width differs with the type of fabric. Check the seams each time, and adjust the cutting width as follows. l.Turn the handwheel toward you until the needles are at the lowest position. 2 .Open the front cover and free arm 3.Turn the cutting width adjustment knob until the looper threads lie along the edge of the ...

  • White 1500 - page 19

    CHANGiNG THE NEEDLE Turn the power switch to “OFF’ before changing the Hexagon wrench key needles. Do not use any needle which is bent or blunt. l.Turn the handwheel toward you until the needles are fully raised. 2.Open the front cover and lower the presser foot. 3. Using the hexagon wrench key from the accessory box, loosen the needle clamp sc ...

  • White 1500 - page 20

    REPLACINGIHE CUTTERS Turn the power switch to “OFF” before replacing the cutter blades. The lower cutter is made of special material and does not usually need to be replaced. However; should it become damaged, it can be replaced by your local dealer. To replace the upper cutter when it becomes dull: l.Open the front cover and turn the handwheel ...

  • White 1500 - page 21

    THREE THREAD NARROW AND WIDE OVERLOCK STITCHI This machine is a 3/4 thread convertible overlock. Remove either the right or left needle. Your machine is now ready for use as a 3-thread overlock. Refer to “CHANGING THE NEEDLE” Using the needle on the right only. The stitch width is 4mm (0.1611) Using the needle on the left only. The stitch width ...

  • White 1500 - page 22

    I FREE ARM SEWING Remove the support bed as illustrated which easily converts from a flat bed to tree arm. Convenient for sewing pant legs, sleeves and cuffs, etc. The special presser foot, is set for normal overlock with the letter N adjacent to the vertical screw at front of presser foot. When you need to sew a rolled edge, simply loosen the larg ...

  • White 1500 - page 23

    I ROLLED AND NARROW EDGE To carry out either of the above sewing tasks proceed as follows. (1) Refer to page 20 for special foot position setting. (2) Turn the handwheel toward you until needles are fully raised. (3) Open front cover and remove left needle. See page 17. (4) Set stitch Length between 1.0-2.0 mm. See page 15. Also ensure that differe ...

  • White 1500 - page 24

    Important: It necessary, adjust the stitch length and cutting width. Threads Fabrics Rolled hemming Narrow hemming Spun polyester Spun polyester Georgette No.50—80 No5O—8O Needle thread Lawn Polyester continuous Polyester continuous Crepe-de No5O8O No.50—80 -chine Spun polyester Wooly-nylon • Silk Upper Spun polyester Wooly-nylon No.50—80 ...

  • White 1500 - page 25

    I DIFFERENTIAL FEED The difterential feed prevents wavy seams in knitted fabrics and also movement between the layers of fabric. It also ensures pucker-tree seams on lightweight fabrics. [DIFFERENTIAL FEED MECHANISM] There ard two sets of feed teeth, one front and one rear, The two sets of teed teeth move independently. Ditterential feed allows the ...

  • White 1500 - page 26

    [WAVY KNITS % GATHERING] For perfectly flat seams in stretchy knit garments, the front feed teeth need to feed faster than the rear feed teeth to prevent stretching the fabric. To Gather, the front feed teeth will also need to feed faster than the rear feed teeth. By using a long stitch length, (see pg. 23 adjust), your fabris will easily gather. S ...

  • White 1500 - page 27

    RbUBLE SHOOTING GUIDE Check items below before calhng for service. Problem Cause Corrective action Page CD Needles are bent, blunt or Replace with new needles. points are damaged. 17 Insert the needles correctly to the CD Needles not inserted correctly. Needles break needle clamp. 17 CD You have forcibly pulled the Guide fabric gently with both fab ...

  • White 1500 - page 28

    LCIJEANING AND LUBRICATING 1 To keep your machine running smoothly ; it is necessary to clean using the brush from the ac cessory box now and then. This machine requires very little lubrication as the main components are made of special materials. Occassionally, lubricate only the points illustrated. [ SPECIFICATION OF MACHINE Description Specifica ...

  • White 1500 - page 29

    S3J.ON ...

Fabbricante White Categoria Sewing Machine

I documenti che otteniamo dal fabbricante del dispositivoWhite 1500 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici White
- manuali per l’uso 1500
- schede prodotto White
- opuscoli
- o etichette energetiche White 1500
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso White 1500.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione White 1500, manuali di manutenzione, brevi manuali o manuali utente White 1500. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto White 1500.

Manuali per l’uso simili

Manuale completo del dispositivo White 1500, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare White 1500 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti White 1500.

Il manuale per l’uso completo White, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale White 1500 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice White 1500, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per White 1500 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo White 1500 - che ci dovrebbe aiutare nei primi passi durante l'uso White 1500
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del White 1500
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio White 1500 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su White 1500?

Utilizza il modulo sottostante

Se non hai risolto il problema con White 1500 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con White 1500 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)