Italiano dropdown-ico

Manuale per l’uso Heatiator BCDV36

28 pagine 1.88 mb
Scarica

Vai alla pagina of 28

Summary
  • Heatiator BCDV36 - page 1

    01-03 1 33606 Rev D INST ALLA TION & OPERA TING INSTRUCTIONS BCDV36 BUILDERS CHOICE DIRECT VENT DECORA TIVE GAS APPLIANCE WARNING! Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual. For assistance or additional information, consult a qualified inst aller , service ...

  • Heatiator BCDV36 - page 2

    33606 Rev D 2 01-03 BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS CONTENTS A . Appliance S pecifications ..................................................................................................... ............................ 3 B . Nomenclature .................................................................................... ...

  • Heatiator BCDV36 - page 3

    01-03 3 33606 Rev D BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS A. APPLIANCE SPECIFICA TIONS 1. U.S. AND CANADA CERTIFICA TION The Builder's Choice Series Gas Appliance has been tested in accordance with the ANSI st andard Z21.50b-1998 and U.L. 307B in the United S tates; in Canada, the current CAN/CGA-M2.22-M98 , and has been LIS ...

  • Heatiator BCDV36 - page 4

    33606 Rev D 4 01-03 BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS TYPICAL HORIZONT AL INST ALLA TION TYPICAL VERTICAL INST ALLA TION ...

  • Heatiator BCDV36 - page 5

    01-03 5 33606 Rev D BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS B. NOMENCLA TURE # g o l a t a Cn o i t p i r c s e D e c i o h C s r e d l i u B - V D C B ) x i f f u s o n ( V D C Bs a g l a r u t a n , t o l i p g n i d n a t S L V D C Bs a g e n a p o r p , t o l i p g n i d n a t S S Cy l n o n o i t a n i m r e t l a t n o z i r ...

  • Heatiator BCDV36 - page 6

    33606 Rev D 6 01-03 BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS C. LOCA TION AND CLEARANCES 1. APPLIANCE LOCA TIONS AND SP ACE REQUIREMENTS Figure 1 illustrates a variety of ways the appliance may be located in a room. The Builder's Choice Series may be installed directly on the floor or on a hearth. These appliances are certified ...

  • Heatiator BCDV36 - page 7

    01-03 7 33606 Rev D BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS D. FRAMING Figure 3 shows a typical framing of this appliance using combustible materials. Figure 4 shows the mantel heights for mantel projections. All required clearances to combustibles must be adhered to. CAUTION: Wear gloves and safety glasses for protection. Figure 3 ...

  • Heatiator BCDV36 - page 8

    33606 Rev D 8 01-03 BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS F . VENTING WARNING - RISK OF FIRE! Air space clearances must be maintained at all times. WARNING - RISK OF FIRE! The horizontal run of vent must have a 1/4 rise for every 1 ft. of run towards the termination. Never al- low the vent to run downward. This could cause hig ...

  • Heatiator BCDV36 - page 9

    01-03 9 33606 Rev D BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS c. No Elbows The maximum horizontal run with no vertical sections of vent is 18 from the back of the appliance to the base of the cap. See Figure 7. d . A 45° Elbow For corner venting, a maximum of one 45° elbow may be used. The maximum horizontal run following the el ...

  • Heatiator BCDV36 - page 10

    33606 Rev D 10 01-03 BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS Figure 1 1 - T ermination Cap Locations DIMENSION DESCRIPTIONS A Clearance above the ground, a veranda, porch, deck or bal- cony - 12 inches (30 cm) minimum. * B Clearance to window or door that may be opened  10,000 BTUs or less, 6 inches (15 cm) minimum; 10,000-50,00 ...

  • Heatiator BCDV36 - page 11

    01-03 11 33606 Rev D BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS 2. VERTICAL TERMINA TION a. Clearances See Figure 13 for clearance information. b . V ent Lengths V arious venting configurations are shown in Figures14 and 15 from which the maximum vent runs can be determined. Figure 13 V ent Clearances Figure 14 - V ent Lengths Figu ...

  • Heatiator BCDV36 - page 12

    33606 Rev D 12 01-03 BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS c. Firestop Spacer/Chimney Installation Frame an opening and install an FS6 Firestop S pacer whenever the vent penetrates a ceiling/ floor area, as shown in Figure 16. Frame the opening with the same sized lumber as used in the ceiling/floor joists. Do not pack insulation ...

  • Heatiator BCDV36 - page 13

    01-03 13 33606 Rev D BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS 1. ATT ACHING THE VENTING TO THE APPLIANCE T o attach the first VP section to the appliance collars, simply slide the flared end of the inner vent of the VP section over the inner collar on the appliance. At the same time, insert the outer vent into the outer collar on th ...

  • Heatiator BCDV36 - page 14

    33606 Rev D 14 01-03 BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS 4. ASSEMBLING SLIP SECTIONS Slip sections should be snapped into the first mating piece, then expanded to their desired length, making sure that a 1.5 overlap is maintained between the two sections of the slip section. The two sections of the slip section then need to ...

  • Heatiator BCDV36 - page 15

    01-03 15 33606 Rev D BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS H. UTILITIES 1. GAS LINE CONNECTION Open the control access panel as shown in Figure 24. See Figure 25 to connect the gas line properly . All connections must be checked for leaks with a soap and water solution or a leak detector . Bleed the gas line to extract any air th ...

  • Heatiator BCDV36 - page 16

    33606 Rev D 16 01-03 BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS Figure 27 Standing Pilot Ignition Wiring Diagram 14-3 with Ground Romex is the recommended wiring to the appliance Junction Box. Detailed picture of the Junc- tion Box (Optional for Stand- ing Pilot Appliances). 4. WIRING Standing Pilot Ignition - Millivolt System a. Appl ...

  • Heatiator BCDV36 - page 17

    01-03 17 33606 Rev D BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS I. FINISHING 1. COMBUSTIBLE FINISHING MA TERIAL Materials made of or surfaced with wood, compressed paper , plant fibers, plastics, or any material capable of igniting and burning, whether flame proofed or not, plastered or unplastered (this includes drywall) are consider ...

  • Heatiator BCDV36 - page 18

    33606 Rev D 18 01-03 BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS J. APPLIANCE PREP ARA TION 1. LOG SET The log set should look similar to that in Figure30. 2. PLACING THE VERMICULITE AND LA V A ROCK See Figure 31. 3. PLACING THE ROCK WOOL Place a small amount of 1/2 diameter pieces (dime sized) of rock wool on the ember tray abov ...

  • Heatiator BCDV36 - page 19

    01-03 19 33606 Rev D BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS 1. Turn off all wall switches to the appliance or remote. 2. Open the control access panel. 3 Turn gas line to CLOSED. Wait 5 minutes to clear out any gas. Then smell for gas, including near the floor . If you smell gas, STOP! Follow B in the safety informatio ...

  • Heatiator BCDV36 - page 20

    33606 Rev D 20 01-03 BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS WARNING! Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition. Y oung children should be carefully supervised when they are in the same room as the appliance. CAUTION: Any safety screen ...

  • Heatiator BCDV36 - page 21

    01-03 21 33606 Rev D BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS M. FUEL CONVERSION Do not burn wood or other material in this appliance. Natural or propane gas conversions necessary to meet the application need to be made by a qualified technician using Hearth & Home T echnologies specified and approved parts. In the event your ap ...

  • Heatiator BCDV36 - page 22

    33606 Rev D 22 01-03 BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS 5. LOG REMOV AL/REPLACEMENT If removal of the logs becomes necessary , remove the two screws at each side of the front log. Grasp the front log. Pull the log toward the front and up, off the burner . See Figure 35. T o replace the logs, grasp the front log. Lower the log ...

  • Heatiator BCDV36 - page 23

    01-03 23 33606 Rev D BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS P . OPTIONAL COMPONENTS Contact your local Heatilator Dealer by calling: 1-800-843-2848. BC10 Fan Motor Rheostat Control JK9 Junction Box Kit FK4 Fan Kit RC-SMART -HTL Remote Control RC-BA TT -HTL Battery-operated (standing pilot) Remote Control RC-SMART -BA TT -HTL Batte ...

  • Heatiator BCDV36 - page 24

    33606 Rev D 24 01-03 BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS Q. REPLACEMENT PARTS Replacement p arts are available from your distributor/dealer . Item 1 BCDV36 Gas Log Assembly M E T I# T R A PN O I T P I R C S E D. Y T Q 16 1 4 9 2. y s s A g o L s a G 6 3 V D C B1 a 19 8 5 8 2g o L t n o r F1 a 26 2 2 5 2g o L t f e L p o T1 a 37 ...

  • Heatiator BCDV36 - page 25

    01-03 25 33606 Rev D BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS HOMEOWNERS NOTES ...

  • Heatiator BCDV36 - page 26

    33606 Rev D 26 01-03 BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS HOMEOWNERS NOTES ...

  • Heatiator BCDV36 - page 27

    01-03 27 33606 Rev D BUILDER'S CHOICE SERIES INST ALLA TION INSTRUCTIONS Index A Access Panel 15 Air Shutter Adjustment 20 Appliance Preparation 18 B Bathtub Areas 3 BC10 23 BTUs 15 Building Codes 3, 8 Burner 21 C Cap Clearances 10 Carbon Monoxide 18 Certification 3 Chase Installation 12 Chimney Height 12 Chimney Height for V ertical T erminat ...

  • Heatiator BCDV36 - page 28

    30532 Rev D 28 01-03 Gas Appliance (Fireplace) Limited Lifetime W arranty HEARTH & HOME TECHNOLOGIES (HHT) extends the following warranty for HEA TILA TOR â gas appliances installed in the United S tates of America or Canada (the Appliance). Dealers and employees of HHT have no authority to make any warranty or authorize any remedi ...

Fabbricante Heatiator Categoria Indoor Fireplace

I documenti che otteniamo dal fabbricante del dispositivoHeatiator BCDV36 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Heatiator
- manuali per l’uso BCDV36
- schede prodotto Heatiator
- opuscoli
- o etichette energetiche Heatiator BCDV36
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Heatiator BCDV36.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Heatiator BCDV36, manuali di manutenzione, brevi manuali o manuali utente Heatiator BCDV36. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Heatiator BCDV36.

Manuali per l’uso simili

Manuale completo del dispositivo Heatiator BCDV36, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Heatiator BCDV36 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Heatiator BCDV36.

Il manuale per l’uso completo Heatiator, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Heatiator BCDV36 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Heatiator BCDV36, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Heatiator BCDV36 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Heatiator BCDV36 - che ci dovrebbe aiutare nei primi passi durante l'uso Heatiator BCDV36
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Heatiator BCDV36
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Heatiator BCDV36 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Heatiator BCDV36?

Utilizza il modulo sottostante

Se non hai risolto il problema con Heatiator BCDV36 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Heatiator BCDV36 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)