-
Wayne-Dalton 347610 - page 1
GARAGE DOORS & OPENERS Part No. IMPORT ANT NO TICES! Wayne-Dalton highly recommends that you read and fully under - stand the Installation Instructions and Owner’ s Manual before you attempt this installation. T o avoid possible injur y , read the enclosed instructions carefully before installing and operating the garage door . Pay close atte ...
-
Wayne-Dalton 347610 - page 2
2 Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com A. TRACK ROLLERS (AS REQUIRED): A1. Short Stem T rack Rollers A2. Long Stem T rack Rollers A3. Sh ...
-
Wayne-Dalton 347610 - page 3
I m p o r t a n t S a f e t y I n s t r u c t i o n s DEFINITION OF KEY WORDS USED IN THIS MANUAL: W ARNING W ARNING INDICA TES A POTENTIALL Y HAZARDOUS SITUA TION WHICH; IF NOT AVOIDED , COULD RESUL T IN SEVERE OR FA T AL INJURY . CAUTION: PROPER TY DAMAGE OR INJURY CAN RESUL T FROM FAILURE TO FOLLOW INSTRUCTIONS. IMPORT ANT : REQUIRED STEP FOR SA ...
-
Wayne-Dalton 347610 - page 4
Cable drums RH/LH Torsion springs RH/LH End bearing brackets RH/LH (as required) End bearing brackets RH/LH (as required) Cotter pin (as required) 5/16” x 1-1/4” Clevis pin (as required) Center bearing bracket assembly (as required) Center bracket bushing assembly (as required) Hinges Half Center hinges (as required) Strut clips (as required) S ...
-
Wayne-Dalton 347610 - page 5
rail of the bottom section. Long Strut(s) are typically installed along the top and or bottom rails of sections. Measure the height of the long strut(s) to determine if you have 2” or 3”. NOTE: Some struts also may or may not have holes in them. If they don’t, then prior to installing the strut and hinge to the section surface, you may have t ...
-
Wayne-Dalton 347610 - page 6
Weatherstrips Level header Finished Door width Jambs Backroom Plumb jambs Finished Door Height Nail Headroom Header board 2”x 6” lumber preferred Suitable mounting surface 2”x 6” lumber minimum Weather- strips Jamb 1/8” to 1/4” Min. side room clearance for 2” track is 3-1/2” (89 mm). Min. side room clearance for 3” track is 4-1/2? ...
-
Wayne-Dalton 347610 - page 7
INST ALLA TION Before installing your door , be certain that you have read and followed all of the instruc- tions covered in the pre-installation section of this manual. Failure to do so may result in an improperly installed door . IMPORT ANT : WOOD DOORS MUST BE COMPLETEL Y FINISHED (3 TOT AL COATS, INCLUDING PRIMER COA T) PRIOR TO INST ALLA TION, ...
-
Wayne-Dalton 347610 - page 8
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com with the left bottom edge of the bottom section. Attach the bottom corner bracket to the bot- tom s ...
-
Wayne-Dalton 347610 - page 9
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com (3) 1/4” - 14 x 1” Lag screws 2” Long strut T ypical section shown. Center hinge FOR 3” LON ...
-
Wayne-Dalton 347610 - page 10
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com Lay a short strut onto the top rail of the top section. Position the top of the strut 3/4” down f ...
-
Wayne-Dalton 347610 - page 11
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com screws. Repeat same process for other inner upper hinge leafs. 2” Long strut T ypical section sho ...
-
Wayne-Dalton 347610 - page 12
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com adjusted for each side. Starting on the left hand side, vertically align the top section of the doo ...
-
Wayne-Dalton 347610 - page 13
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com IMPORT ANT : THE CENTER BRACKET BUSHING OR CENTER BEARING AND TORSION SPRINGS, MUST BE POSITIONED, ...
-
Wayne-Dalton 347610 - page 14
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com Center bearing Coupler assembly Center bearing bracket(s) T orsion keyed shaft Center bearing insid ...
-
Wayne-Dalton 347610 - page 15
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com Winding Springs T ools: Step Ladder , Approved winding bars, 3/8” Wrench 23 Position a ladder sli ...
-
Wayne-Dalton 347610 - page 16
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com Vice clamp Horizontal tracks 2nd T rack roller Vice clamp 5/16”-18 x 1-1/4” Hex bolts must exte ...
-
Wayne-Dalton 347610 - page 17
Door Arm Hookup T ools: Needle nose pliers At the center of the top section, measure horizontally from the top of center hinge to the bottom of strut. Using that dimension, measure and cut (2) pieces of perforated angles. Assemble the (2) pieces together using (2) 3/8” bolts and nuts (supplied by others). Now, secure to the top section using carr ...
-
Wayne-Dalton 347610 - page 18
Cleaning Y our Garage Door IMPORT ANT : DO NOT USE A PRESSURE W ASHER ON YOUR GARAGE DOOR! An annual inspection of all the surfaces of your garage door(s) will reveal the extent of weather - ing and the possible need for refinishing. When the finish becomes eroded or thin, clean and prime any areas showing deterioration. Then completely refinish ...
-
Wayne-Dalton 347610 - page 19
3. Lubrication: The door should open and close smoothly. Ensure the door track rollers are rotating freely when opening and closing the door . If track rollers do not rotate freely, clean the door tracks, removing dirt and any foreign substances. Clean and lubricate (use a non-silicon based lubricant) graduated end hinges, steel track rollers, spri ...
-
Wayne-Dalton 347610 - page 20
Limited warranty Model 7000 and 7400 Series Subject to the terms and conditions contained in this Limited Warranty , Wayne-Dalton (“Manufacturer”) warrants the sections of the door , against defects in material and workmanship, for a period of ONE (1) YEAR from the time of delivery provided: i) (i) The interior and exterior surfaces, as well as ...
-
Wayne-Dalton 347610 - page 21
...
-
Wayne-Dalton 347610 - page 22
AFTER INST ALLA TION IS COMPLETE, F ASTEN THIS MANUAL NEAR THE GARAGE DOOR. Please Do Not Return This Product T o The Store Thank you for your pur chase. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pa ges business listings or go to the Find a Dealer section online at www .Wayne-Dalt ...
Hai una domanda su Wayne-Dalton 347610?
Utilizza il modulo sottostante
Se non hai risolto il problema con Wayne-Dalton 347610 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Wayne-Dalton 347610 è probabile che voglia condividere il modo di risolverlo.