Manuale per l’uso Smith Cast Iron Boilers 28HE

28 pagine 2.29 mb
Scarica

Vai alla pagina of 28

Summary
  • Smith Cast Iron Boilers 28HE - page 1

    SERIES 28HE GAS OR OIL BOILER INST ALLA TION & OPERA TING INSTR UCTIONS DESIGNED AND TESTED A CCORDING T O A.S.M.E. BOILER AND PRESSURE VESSEL CODE, SECTION IV FOR A MAXIMUM ALLO W ABLE WORKING PRESSURE OF: 15 PSI STEAM OR 80 PSI W A TER. W ARNING: If the inf ormation in this manual is not f ollowed exactl y , a fire or e xplosion may result ca ...

  • Smith Cast Iron Boilers 28HE - page 2

    Page 2 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS CONTENTS Bef ore Y ou Star t ................................................. page 2 Boiler Ratings & Capacities ................................ page 2 Boiler Location ................................................... page 2 Combustion Air & V entilation ............. ...

  • Smith Cast Iron Boilers 28HE - page 3

    Page 3 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS Figure 1 -Service Clearances to Adjacent Construction W ARNING: Never install a 28HE boiler on top of combustib le flooring without consulting the local building authorities f or proper installation guidelines! A minimum c learance of 6 in, 0.15 m must be maintained between the b ...

  • Smith Cast Iron Boilers 28HE - page 4

    Page 4 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS All Air From Inside The Buidling If the boiler is to be located in a confined space mini- mum clearances of 24 in , 610 mm must be maintained between the boiler and any adjacent construction. When installed in a confined space, two permanent openings communicating with an additio ...

  • Smith Cast Iron Boilers 28HE - page 5

    Page 5 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS Chimney Inspection & Sizing If this boiler will be connected to a masonr y chimney , a thorough inspection of the chimney m ust be perf or med. Ensure that the chimney is clean, properly constructed, lined and properly sized, see Figure 2. T able 2 lists the equivalent breech ...

  • Smith Cast Iron Boilers 28HE - page 6

    Page 6 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS W ARNING: Failure to maintain minimum clearances between vent connector s and any combustib le material can result in a fire causing extensive pr operty damage, se vere per sonal injury or death! COMMON VENT SYSTEMS If an e xisting boiler is remov ed from a common venting system, ...

  • Smith Cast Iron Boilers 28HE - page 7

    Page 7 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS c) Insof ar as is practical, close all building doors and windows and all doors between the space in which the appliances remaining connected to the common venting system are located and other spaces of the building. T urn on clothes dr y ers and any appliance not connected to th ...

  • Smith Cast Iron Boilers 28HE - page 8

    Page 8 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS 2 . Carefully place the back section in position on the angles as shown in Figure 4. W ARNING: The section MUST be fully supported to prevent it fr om falling! Failure to comply with this warning may result pr oper ty damage, severe per sonal injury or death! Figure 4 - Section P ...

  • Smith Cast Iron Boilers 28HE - page 9

    Page 9 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS 5 . Inser t the large por t connector with its steel inner ring into the upper port. 6 . Inser t the two round por t connectors into the lower por ts. NO TE: Appl y the spra y adhesive supplied with the boiler to the port recess to hold the por t connector in place if necessary . ...

  • Smith Cast Iron Boilers 28HE - page 10

    Page 10 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS 9 . Assemble the rest of the sections f ollowing steps 3 through 8 abov e. 1 0 . Hydrostatically test the boiler by f ollowing the instructions on page 8. 11. While the boiler is being filled confirm that all of the draw r ods are properly tor qued and that there are no leaks. 1 ...

  • Smith Cast Iron Boilers 28HE - page 11

    Page 11 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS Observation P or t Assembl y , Figure 10 1 . P osition the hinged end of the steel flapper door , item 5, ov er the boss on the obser vation por t cov er , item 4. 2 . Drive the e xpansion pin, item 7, through the hinge bosses to secure the door to the cov er . 3 . Inser t the h ...

  • Smith Cast Iron Boilers 28HE - page 12

    Page 12 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS Observation P or t Installation 1 . Screw the f our 5/16-18 x 1 1/2" studs into the tapped holes around the obser vation co v er opening in the back section. 2 . Place the obser vation por t cov er assembly ov er the studs and install the washers and nuts . Tighten the nuts ...

  • Smith Cast Iron Boilers 28HE - page 13

    Page 13 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS T ankless Heater Installation - Optional 1 . Clean the heater flange to remove an y r ust or debris. 2 . Install the f our 7/16" x 1 1/2" studs into the tapped holes in the tankless heater flange on the section, Figure 12. Figure 12 - T ankless Heater Installation 3 . ...

  • Smith Cast Iron Boilers 28HE - page 14

    Page 14 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS Figure 15 - Back Section T apping Locations T able 5 - Water & Steam T appings Relief & Safety V alve Piping Install the pressure relief or safety v alve in the 3" NPT opening in the top of the back section, Figure 14. W ARNING: The discharge of the pressure relief ...

  • Smith Cast Iron Boilers 28HE - page 15

    Page 15 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS Figure 16 - Relief & Safel y V alve Piping W A TER BOILER PIPING The supply and retur n connections should be sized to suit the system, see Figures 14, 15, 17, 18 and T ables 5 & 6. Do not pipe the supply from the bottom por t or the return to the top por t, the boiler w ...

  • Smith Cast Iron Boilers 28HE - page 16

    Page 16 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS Figure 17 - Optional Return Y oke Figure 18 - Boiler Contr ol Locations Piping For Use With Cooling Units The boiler , when used in connection with a refr igeration system, must be installed so the chilled medium is piped in parallel with the boiler . Appropriate valves m ust be ...

  • Smith Cast Iron Boilers 28HE - page 17

    Page 17 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS Figure 19 - T ypical Single W ater Boiler Piping Figure 20 - T ypical Multiple W ater Boiler Piping ...

  • Smith Cast Iron Boilers 28HE - page 18

    Page 18 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS Figure 21 - Chilled Medium Diagram Cleaning of Water Boiler s Nor mally the cleaning of water boilers is unnecessary unless there is unusually hea vy contamination of the boiler or system. The burner must be installed and made operational along with the operating, limit and othe ...

  • Smith Cast Iron Boilers 28HE - page 19

    Page 19 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS Minimum F eed W ater Condensate Receiver Boiler I=B=R Gross Output Ev aporation Rate Pumping Rate Capacity Model MBH kW GPM L/hr GPM L/hr Gallons Liters 28HE-S-4 900 264 1.9 7.3 3.9 14.8 37 140 28HE-S-5 1166 342 2.5 9.5 5.0 18.9 48 182 28HE-S-6 1433 420 3.1 11.7 6.2 23.5 59 223 ...

  • Smith Cast Iron Boilers 28HE - page 20

    Page 20 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS Figure 23 - T ypical Steam Piping - Gravity Return f or Multiple Boilers Figure 24 - T ypical Steam Piping - Pumped Return f or Multiple Boilers ...

  • Smith Cast Iron Boilers 28HE - page 21

    Page 21 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS CA UTION: A v oid skin contact with c leaning solution to prevent injury! If e y e or skin contact occur s flush with large quantities of water . NO TE: Some locations do not allo w this solution to be used. Check with the local authority having jurisdiction. 5 . Mix the cleanin ...

  • Smith Cast Iron Boilers 28HE - page 22

    Page 22 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS W ater Boilers Fill the boiler and all of the radiation with water to the required system pressure. Completely purge the system of air and adjust the system pressure as needed. CA UTION: Thermal shock of water boilers m ust be av oided! W ater circulation must be estab lished be ...

  • Smith Cast Iron Boilers 28HE - page 23

    Page 23 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS CA UTION: If the flue gas temperature exiting the smoke hood is less than 320 ° F, 160 ° C at full rated input, the number of heat transfer r ods in the boiler must be reduced. Failure to pr otect the boiler from low flue gas temperatures will shorten the life of the boiler an ...

  • Smith Cast Iron Boilers 28HE - page 24

    Page 24 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS BOILER MAINTENANCE W ARNING: Servicing, inspection and adjustment of the boiler must be done b y a trained technician in accor dance with all applicable local and national codes. Improper servicing or adjustment can result in property damage, severe per sonal injury or death! Th ...

  • Smith Cast Iron Boilers 28HE - page 25

    Page 25 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS Figure 26 - Boiler Assembl y ...

  • Smith Cast Iron Boilers 28HE - page 26

    Page 26 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS (1) Smokehood assemb ly includes the smokehood, slide damper , angle brack et and hardware. (2) Cleanout cov er assembly includes the cleanout co v er , insulation, rope and mounting hardware. 1 F ront Section 3621 111111111111111 2 Graphite P or t Connector Set 60375 3456789 1 ...

  • Smith Cast Iron Boilers 28HE - page 27

    Page 27 SERIES 28HE BOILER INST ALLA TION AND OPERA TION INSTR UCTIONS 33 Obser vation Glass Co ver Plate 3420 1 11111111111111 ns Rear Observation P ort Hardware 71301 1 1 1 1 1 1 111111111 Burner Mounting Plate Assembly , 9" 70641 Burner Mounting Plate Assembly , 10 1/4" 70640 34 (3) Burner Mounting Plate Assembly , 12 1/2" 70510 B ...

  • Smith Cast Iron Boilers 28HE - page 28

    dizziness headaches nausea vision problems loss of muscle control weakness shortness of breath unclear thinking unconsciousness W ARNING Any appliance that burns natural gas, propane gas, fuel oil, wood or coal is capable of producing carbon monoxide (CO). Carbon Monoxide (CO) is a gas which is odorless, colorless and tasteless but is very toxic. I ...

Fabbricante Smith Cast Iron Boilers Categoria Blower

I documenti che otteniamo dal fabbricante del dispositivoSmith Cast Iron Boilers 28HE possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Smith Cast Iron Boilers
- manuali per l’uso 28HE
- schede prodotto Smith Cast Iron Boilers
- opuscoli
- o etichette energetiche Smith Cast Iron Boilers 28HE
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Smith Cast Iron Boilers 28HE.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Smith Cast Iron Boilers 28HE, manuali di manutenzione, brevi manuali o manuali utente Smith Cast Iron Boilers 28HE. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Smith Cast Iron Boilers 28HE.

Manuale completo del dispositivo Smith Cast Iron Boilers 28HE, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Smith Cast Iron Boilers 28HE dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Smith Cast Iron Boilers 28HE.

Il manuale per l’uso completo Smith Cast Iron Boilers, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Smith Cast Iron Boilers 28HE - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Smith Cast Iron Boilers 28HE, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Smith Cast Iron Boilers 28HE che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Smith Cast Iron Boilers 28HE - che ci dovrebbe aiutare nei primi passi durante l'uso Smith Cast Iron Boilers 28HE
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Smith Cast Iron Boilers 28HE
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Smith Cast Iron Boilers 28HE in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Smith Cast Iron Boilers 28HE?

Utilizza il modulo sottostante

Se non hai risolto il problema con Smith Cast Iron Boilers 28HE con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Smith Cast Iron Boilers 28HE è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)