Italiano dropdown-ico

Manuale per l’uso Paxar Monarch 415

28 pagine 0.74 mb
Scarica

Vai alla pagina of 28

Summary
  • Paxar Monarch 415 - page 1

    Monarch 415 TM Rewind Operator’ s Handbook TC0415OH Rev. D 5/96 ©1990-96 Monarch Ma rking Systems, Inc. All rights reserved. ...

  • Paxar Monarch 415 - page 2

    Each product and program carries a respectiv e writ ten warranty , the only warr anty on which the customer can rely . Monarch reser v es the right t o mak e changes in the product and the programs and their av ailability at any time and without notice. Although Monarch has made e v er y effor t to provide complete and acc urate inf or mation in th ...

  • Paxar Monarch 415 - page 3

    Table of Conten ts 1. Setting Up ...... ........ ........ ...... ........ .......... ........ ........ ...... ...... 1 2. Connecting Supplies ...... ........ ........ ...... ........ .......... ........ .. 3 Rewinding on the Hub ..... ...... ...... ........ ...... ...... ...... ....... 3 Rewinding on a P aper Core .......... ...... ........ ...... ...

  • Paxar Monarch 415 - page 4

    Monarc h 415 Rewind Operato r ’ s Ha ndbook ii ...

  • Paxar Monarch 415 - page 5

    1. Setting Up 1. Push the 415 Rewind pow er s witch OFF . 2. Place the re wind on a le vel surf ace. Be sur e it is at least ten inches a wa y from the supply e xit of the printer (Figure 1). 3. Squarely align the rewind’ s hub flange with the edge of the supply . See Appendix A, "R ewind Alignm ent." Figure 1 Pow e r Swit ch Prin ter S ...

  • Paxar Monarch 415 - page 6

    4. Plug the power cord into the rewind ( Figur e 2). Then, plug the pow e r cord into a grounded elec tr ical outlet. Figure 2 Po w e r Cor d Po w e r Switch Fuse Holder Monarc h 415 Rewind Operato r ’ s Ha ndbook 2 ...

  • Paxar Monarch 415 - page 7

    2. Con necting Suppli es Rewinding on the Hub 1. Slide the supply guide a wa y from the hub flange and pull it aw ay from the hub. 2. Print or f eed enough supplies from the pr inter to wrap around the hub one and one half times. 3. Hold the hub flange and twist the hub cl o ck wi se until it stops. 4. Thread the supply str ip under the dancer roll ...

  • Paxar Monarch 415 - page 8

    6. T ur n the hub and hub flange at leas t one full turn counterc lockwise to tighten the supply strip . 7. Push the supply guide against the hub then slide it against the supply . NOTE: Units with 3" hubs ha ve a flanged disk instead of a supply guide . Slide this disk ov er t he hub and against the stock / core (Figure 4). Figur e 4 Monarc h ...

  • Paxar Monarch 415 - page 9

    Rewinding on a P aper Core 1. Slide the supply guide a wa y from the hub flange and pull it aw ay from the hub. 2. Push the paper core on t he hub until it is against the hub flange. 3. Hold the hub flange and twist the hub cl o ck wi se until the paper core is tight. 4. T ape the supply str ip to the paper core (Figure 5). Be sure the supply is ag ...

  • Paxar Monarch 415 - page 10

    5. T ur n the hub and hub flange at leas t one full turn counterc lockwise to tighten the supply strip . 6. Push the supply guide against the hub then slide it against the supply . Monarc h 415 Rewind Operato r ’ s Ha ndbook 6 ...

  • Paxar Monarch 415 - page 11

    3. Operating the Rewind Starting 1. T ur n the speed control knob ( Figure 6) to SLO W . 2. Push the rewind pow er s witch (Figure 7) ON . NOTE: The rewind will star t to tur n. When the dancer roller is almost horizontal, the rewind will stop. 3. Star t t he printer . 4. Adjust the re wind speed to the speed of the printer . NOTE: If you stop the ...

  • Paxar Monarch 415 - page 12

    Stopping 1. Stop the pr inter . 2. Push the rewind pow er s witch OFF . 3. Pull the supply guide a wa y from the hub . 4. Cut the supply at the s upply e xit of the pr inter (Figure 8). 5. T ape the end of the supply to the r oll on the rewind. 6. Pull the supply guide a wa y from hub . 7. Hold the hub flange and turn the hub counter clockwise unti ...

  • Paxar Monarch 415 - page 13

    4. Ch anging Hubs If y ou change to a diff er ent supply , you may need to use a diff er ent hub . One, three , and f our inch diam eter hubs (shor t and long) are a vailab le from Monarch. T o change hubs 1. Pull the supply guide a wa y from the hub (Figure 9) . 2. Unscre w the hub knob (Figure 10) . NOTE: The hub diameter m ust be the same as the ...

  • Paxar Monarch 415 - page 14

    3. Remov e the hub sections and replace them with the new ones (Figure 11). a. Slide the new hub spindle on t he shaft. Be sure the notch fits over t he raised portion of the hub flange. b. Slide the hub sections on t o the shaft with t he open ends facing out. The hub section that f its against the hub spindle has two c u rved grooves instead of p ...

  • Paxar Monarch 415 - page 15

    5. Burster Option Setup and Operation Proper positioning of t he printer , burster , and supplies is critical. 1. Place the Rewind/Burster assemb ly in the proper position in front of the pr inter . A dra wing showing the correct position f or all suppor ted pr inters and optional location guides f or alignment is inside the bac k co ver . 2. Print ...

  • Paxar Monarch 415 - page 16

    4. Figure 13 shows the b urster with the supplies installed. Place the separator bars in their approxim ate working positions (i.e. in line with t he perf orations). When only one bar is needed (f or two par t supply), slide un used bar to the outboard side. 5. Thread the inner str ip of supplies under t he dancer ar m roller , behind the two lo we ...

  • Paxar Monarch 415 - page 17

    8. Slide the first core onto the 415 hub until it is against the hub flange. 9. Hold the hub flange and twist the hub clockwise until the paper core is tight. 10. P osition the slot in the hub t o the top . 11. Align the leading edge of the first label on t he inside str ip with the slot in the hub and tape t he supply to the core (Figure 14). Labe ...

  • Paxar Monarch 415 - page 18

    12. Slide the separator disk and t he ne xt core ont o the hub (Figure 15). 13. Hold the core against the separator disk, inser t t he core lock (met al strip) into the slot, and slide it into the c or e . 14. Align the leading edge of the first label on t he middle s t rip with the slot in the hub and tape t he supply to the core. First Se parator ...

  • Paxar Monarch 415 - page 19

    15. Hold the second separator disk with the inside not ch up (in line with the core loc k) and slide it onto the hub (Figure 16). 16. Place the third core over the core lock and slide it onto the hub . Second Separator Disk Third Core Core Loc k Notc h in Disk Figur e 16 5. Burster O p tion Setup an d O peration 15 ...

  • Paxar Monarch 415 - page 20

    17. Slide the third core against the second separ ator disk (Figure 17). 18. Align the leading edge of the first label on t he outside s t rip with the slot in the hub and tape t he supply to the core. Second Separator Disk Label Ed ge Slot Figur e 17 Monarc h 415 Rewind Operato r ’ s Ha ndbook 16 ...

  • Paxar Monarch 415 - page 21

    19. Hold the flanged collar assemb ly wit h the opening in the collar up . Then install it on the hub as shown in Figure 18. Opening in Collar Figur e 18 5. Burster O p tion Setup an d O peration 17 ...

  • Paxar Monarch 415 - page 22

    20. Rechec k the print er to re wind alignment and fine adjust as necessary . 21. V erify that the separator bars are loc at ed between th e strip as shown in Figure 19. 22. V erify that the labels on all thr ee strips are aligned. NOTE: All labels must be aligned as though the supply was ne v er separated to pre vent tor n strips or labels coming ...

  • Paxar Monarch 415 - page 23

    Supply Remo va l 1. Remov e the core lock (metal str ip). 2. Remov e the flanged collar assembly . 3. Remov e the outside core and r oll of labels. 4. Remov e the second separator disk. 5. Remov e the middle core and r o ll of labels . 6. Remov e the inside separator disk. 7. Unlock the inside core. 8. Remov e the inside core and r oll of labels 5. ...

  • Paxar Monarch 415 - page 24

    Monarc h 415 Rewind Operato r ’ s Ha ndbook 20 ...

  • Paxar Monarch 415 - page 25

    6. Sp ecifica tions a nd Supp lies Specifications Height: Width: Depth: 13.75 inches (349.25 mm) 12.50 inches (317.5 mm) 11.5 inches (292.10 mm) Weight: 18 lbs. (8.14 kg) Shipping Weight: 20 lbs. (9.05 kg) Powe r: 115 VAC 60 HZ 30 Watts .3 Amps 220/240 50/60 HZ 30 Watts .15 Amps Fuse: 3/8 Amp Temperature: Operating: 50° to 95° F (10° to 35° C) ...

  • Paxar Monarch 415 - page 26

    7. Troubl eshooti ng Problem Corrective Action Power switch light does not light. Connect the power cord. Call Monarch Service. Dancer arm does not activate the rewind. Make sure the rewind is on a level surface. 22 ...

  • Paxar Monarch 415 - page 27

    Append ix A: Rewind Alignme nt Locati on Guid e 1135 80 Locati on Guid e 1135 76 Locat ion Guide not availa ble Locati on Guid e 1135 76 Locat ion Gu ide 1135 76 Locat ion Gu ide 1135 76 Locati on Guid e 1146 64 23 ...

  • Paxar Monarch 415 - page 28

    F or supplies, service, or assis t ance c all: TOLL FREE: 1-800- 543-66 50 (In the U.S. A.) 1-800- 263-4650 (In Canada) www.paxa r.com ...

Fabbricante Paxar Categoria Switch

I documenti che otteniamo dal fabbricante del dispositivoPaxar Monarch 415 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Paxar
- manuali per l’uso Monarch 415
- schede prodotto Paxar
- opuscoli
- o etichette energetiche Paxar Monarch 415
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Paxar Monarch 415.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Paxar Monarch 415, manuali di manutenzione, brevi manuali o manuali utente Paxar Monarch 415. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Paxar Monarch 415.

Manuali per l’uso simili

Manuale completo del dispositivo Paxar Monarch 415, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Paxar Monarch 415 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Paxar Monarch 415.

Il manuale per l’uso completo Paxar, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Paxar Monarch 415 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Paxar Monarch 415, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Paxar Monarch 415 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Paxar Monarch 415 - che ci dovrebbe aiutare nei primi passi durante l'uso Paxar Monarch 415
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Paxar Monarch 415
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Paxar Monarch 415 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Paxar Monarch 415?

Utilizza il modulo sottostante

Se non hai risolto il problema con Paxar Monarch 415 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Paxar Monarch 415 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)