Italiano dropdown-ico

Manuale per l’uso Vermont Casting EWF36A

32 pagine 2.16 mb
Scarica

Vai alla pagina of 32

Summary
  • Vermont Casting EWF36A - page 1

    EWF36A Fireplace Homeowner ’ s Installation and Operating Manual Do Not Discard This Manual: Retain for Future Use 20005167 7/06 Rev . 1 1 5167 EP A36 cover 3/02 SAFETY NOTICE: IF THIS APPLIANCE IS NOT PROPERL Y INST ALLED, OPERA TED AND MAIN- T AINED, A HOUSE FIRE MA Y RESUL T . TO REDUCE THE RISK OF FIRE, FOLLOW THE INST ALLA TION INSTRUCTIONS. ...

  • Vermont Casting EWF36A - page 2

    2 V er mont Castings EWF36A 20005167 Introduction Thank you for purchasing a V ermont Castings, EWF36A fireplace. An efficient fireplace carefully engineered to bring you the latest in wood combustion principles and modern foundry technology . Y ou can count on years of comfortable heating and pleasurable fire viewing if you treat it properly a ...

  • Vermont Casting EWF36A - page 3

    3 V er mont Castings EWF36A 20005167 Safety Information Please Read This Manual Before Installing and Using Fireplace IMPORT ANT : Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty . Description The EWF36A fireplace is a s ...

  • Vermont Casting EWF36A - page 4

    4 V er mont Castings EWF36A 20005167 Specifications Range of heat output* ............... 1 1,300 - 75,500 Btu/hr Maximum heat output** ..... in excess of 100,000 Btu/hr EP A emissions rating (g/h, catalytic) .......................2.4* Area heated*** ............... Up to 2500 sq. ft. (558 sq. m) Size of wood splits ..................... 18” - ...

  • Vermont Casting EWF36A - page 5

    5 V er mont Castings EWF36A 20005167 Fig. 2 Fireplace and chase parts identification. FP554a FP554a BFC Fireplace and chase parts identification circulating model 8/21/00 djt Chase Installation Insulation methods shown are optional for cold climate, not a requirement for unit operation. T ermination Cap Storm Collar Pan Flashing Draftstop Batt Ins ...

  • Vermont Casting EWF36A - page 6

    6 V er mont Castings EWF36A 20005167 D Rise B G H B Offset C E 6 FT . G H A Hearth Floor Chimney Section CHIMNEY FLUE EXIT Elbow FP269 MBUF 5/16/96 rev . 5/25 TCS8A Support Example 1 Example 2 Example 3 Chimney Requirements - Offset Installations Notes: G + H cannot exceed 20 feet. Air Space Clearances: “S” Series (3-wall) = 2” Min. to Combus ...

  • Vermont Casting EWF36A - page 7

    7 V er mont Castings EWF36A 20005167 Planning Information Determine how the chimney will be run, length of run and chimney components required to complete the job. (Fig. 4) Never install a chimney below minimum heights. In planning a chimney system, it is important to know: 1. The height of a chimney is measured from the hearth to the exit point on ...

  • Vermont Casting EWF36A - page 8

    8 V er mont Castings EWF36A 20005167 Chimney Supports The chimney system is supported by the fireplace for vertical chimney heights less than 30’ (9m) above the hearth. Chimney supports are required if the vertical height exceeds 30’ (9m). Locate chimney supports at ceiling holes or other structural framing at 30’ (9m) heights. Spacing betwe ...

  • Vermont Casting EWF36A - page 9

    9 V er mont Castings EWF36A 20005167 Framing Framing can be constructed before or after the fireplace is set in place, however , most installers build the frame before setting the fireplace. Frame fireplace with 2 x 4 lumber or heavier materi- als. Refer to framing dimensions in Figure 1 for basic fireplace specifications. NOTE: Framing should ...

  • Vermont Casting EWF36A - page 10

    10 V er mont Castings EWF36A 20005167 Ceiling Chimney Hole/ Possible Obstructions The size of the hole in ceiling will vary with the angle at which the chimney passes through ceiling. Drive a nail up through ceiling at marked chimney center point. Go to floor above and see where hole will be cut. Check to see where existing ceiling joists and othe ...

  • Vermont Casting EWF36A - page 11

    1 1 V er mont Castings EWF36A 20005167 Installating Outside Air Kit An outside air kit may be installed on the EWF36A. If desired, or if local codes mandate the use of an air kit, then two (2) AK-MST s are required to complete the installation (from air kit to the outdoors). If the outside air kits are to be used, the AK-MST s MUST be installed BEF ...

  • Vermont Casting EWF36A - page 12

    12 V er mont Castings EWF36A 20005167 Installing the Chimney System Start by attaching the first chimney section to the collar on top of the fireplace. Install the pipe as pictured in Figure 15. When you get a good lock, you will hear the pipe clearly snap together . Once sections are snap-locked in place, it is extremely difficult to get them a ...

  • Vermont Casting EWF36A - page 13

    13 V er mont Castings EWF36A 20005167 If the area above the ceiling is not an attic, position the firestop spacer with the flange on the ceiling side and the angled portion extending up into the hole. If the area above the ceiling is an attic, position the firestop spacer with the flange on the top of the framed hole and the angled portion exte ...

  • Vermont Casting EWF36A - page 14

    14 V er mont Castings EWF36A 20005167 burnable materials such as: ceiling members, joists, flooring, combustible insulation and roof structures.) W ARNING: Do not pack required air spaces with insulation or other materials. Mark an outline of the roof hole around the center of the point nail. NOTE: Hole dimensions given in the chim- ney top instal ...

  • Vermont Casting EWF36A - page 15

    15 V er mont Castings EWF36A 20005167 FP531 Fireplace surround detail 1/29/99 djt Must be sealed with noncombustible material Mantel Shelf Side View Finished W all 2 x 4 Stud Standoff Cast Front See mantel drawing for shelf-to-grille dimension 1” (25mm) Fireplace Front (Steel) 2 x 4 Stud FP1200 Fig. 20 Finishing materials placement. Brick Ledge N ...

  • Vermont Casting EWF36A - page 16

    16 V er mont Castings EWF36A 20005167 The top of insulation must be covered with a non-com- bustible decorative covering or a piece of .018” mini- mum sheet metal, to protect hearth extension material. (Fig. 25) Secure the hearth extension to the floor to prevent shifting, using trim molding or other similar means at three (3) outer edges. Seal ...

  • Vermont Casting EWF36A - page 17

    17 V er mont Castings EWF36A 20005167 FP1201 Fig. 25 Combustible side wall protection and hearth extension dimensions. Minimum W all Clearances WITH Noncombustible Surround Facing WITHOUT Noncombustible Surround Facing Minimum Hearth Extension Dimensions (for On-Site Construction) G H G J Seal cracks between the fireplace and hearth extension with ...

  • Vermont Casting EWF36A - page 18

    18 V er mont Castings EWF36A 20005167 Operation Attach Handles The fallaway handles are used to open and close the front doors. Remove after each use so they will not get hot. Keep in convenient location for each use. (Fig. 26) Assemble the primary air control and damper handles by passing the 3 ³⁄₈ ” screw through the ceramic shaft and into ...

  • Vermont Casting EWF36A - page 19

    19 V er mont Castings EWF36A 20005167 KT108b BFC Correct door position 8/23/00 djt KT108b Fig. 29 Correct door position during operation. Correct Optional Spark Screen Correct The Fan Heated air from the fireplace is forced into the room by an internal fan. The control for the fan is in the right corner of the unit. “Off” is to the far left. ? ...

  • Vermont Casting EWF36A - page 20

    20 V er mont Castings EWF36A 20005167 Starting and Maintaining a Wood Fire Burn solid wood fuel only in the EWF36A, and burn it directly on the grate. Do not elevate the fuel. Do not burn coal or other fuels. Minimize thermal stress by allowing the plates to adjust gradually during an initial break-in fire by following Steps 1-3 below . W ARNING: ...

  • Vermont Casting EWF36A - page 21

    21 V er mont Castings EWF36A 20005167 Different results may be experienced even in the same installation if you switch from burning good, dry wood to wood that is partially rotted or inadequately seasoned. T o compensate for these factors in cold climates, it may be necessary to operate the EWF36A with the air con - trol set to a higher level more ...

  • Vermont Casting EWF36A - page 22

    22 V er mont Castings EWF36A 20005167 Keep your EWF36A Fireplace Looking New and Working Its Best Care of the Cast Iron Surface An occa sio nal dus ting wit h a dry ra g wi ll k eep the pa inte d cas t ir on of y our EWF 36A fire plac e l ooki ng n ew. If the paint needs retouching, first allow the surface to cool completely . Wire-brush areas ne ...

  • Vermont Casting EWF36A - page 23

    23 V er mont Castings EWF36A 20005167 When to Suspect a Combustor Problem The bes t w ay t o e valu ate the per for manc e of yo ur EWF 36A’ s c ombu sto r is to obs erve th e am ount of smo ke lea ving th e ch imn ey - bot h w hen the com bust or has “li ghte d-o ff” and whe n it ha s no t. Foll ow t hes e st eps : • With a fire going and ...

  • Vermont Casting EWF36A - page 24

    24 V er mont Castings EWF36A 20005167 Replaceable Fiberglass Gaskets Gasket Size... ...And The Parts It Seals 1/2” The door to the front 5/8” Door to the hearth brick support 3/16” The glass seal to the door 1/2” Cat holder to top plate 1/2” Braided Damper to top plate Should you need to change a replaceable gasket, wait until the fire i ...

  • Vermont Casting EWF36A - page 25

    25 V er mont Castings EWF36A 20005167 The prefabricated chimney used with your fireplace should be cleaned from above using an 8” round brush and the appropriate number of extension rods for com- plete access. The chimney cap first must be removed following the procedure recommended by the manufacturer . After thoroughly cleaning the chimney , ...

  • Vermont Casting EWF36A - page 26

    26 V er mont Castings EWF36A 20005167 Chimney Components Component Description Model Number Chimney Support Used to support chimney for each of TCS8A 30’ vertical height and 6’ of angled chimney run (8” flue) Firestop Required at each floor level and attic on FS2A (8” straight flue) multi-story installation FS6A (8” 30° inclined flue ...

  • Vermont Casting EWF36A - page 27

    27 V er mont Castings EWF36A 20005167 1 3 7 5 6 1 1 46 40 13 13 20 22 15 86 15 10 37 36 47 47 45 41 44 16 16 17 39 52 27 28 29 30 31 19 33 34 35 9 54 32 42 43 2 2 4 56 55 52 48 51 50 49 73 74 EWF36CLK 75 75 65 EWF36CLK EWF36CLK 76 76 EWF36CLK 79 79 80 80 82 83 84 85 81 82 83 84 85 EWF36S 24 25 26 24 25 26 18 24 25 26 87 38 62 63 64 EWF36CFTK 24 25 ...

  • Vermont Casting EWF36A - page 28

    28 V er mont Castings EWF36A 20005167 22. Glass Right Door - EP A Front 20005152 23. Right, Door Handle Assy . V ert. Nickel 20006286 24. Damper Steel Handle w/Screw 5004265 25. Handle, Ceramic Blk 2.78 Lg 20006381 26. Ov Hd Sl 1/4-20 x 3/375 Lg 1201294 27. Linkage Assy . 20005307 28. Pawl, T op 20005154 29. Pawl, Bottom 20005155 30. Link, EP A FP ...

  • Vermont Casting EWF36A - page 29

    29 V er mont Castings EWF36A 20005167 Optional Accessories Fan Kit FK26 Fan The FK26 fan helps distribute heated air from within the firebox out into the room. The fan is controlled by a snapstat that turns power on and off as the firebox tem- perature rises above and falls below a preset tempera- ture. A rheostat provides for variable fan speeds ...

  • Vermont Casting EWF36A - page 30

    30 V er mont Castings EWF36A 20005167 ...

  • Vermont Casting EWF36A - page 31

    31 V er mont Castings EWF36A 20005167 W arranty Limited 3 Y ear W arranty CFM Corporation warrants that this woodburning stove will be free of defects in material and workmanship for a period of three years from the date you receive it, except that the catalyst, thermostat assembly , handles, glass door panels, cement, and gasketing shall be warran ...

  • Vermont Casting EWF36A - page 32

    2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3 800-668-5323 • www .cfmcorp.com CFM Corporation ...

Fabbricante Vermont Casting Categoria Indoor Fireplace

I documenti che otteniamo dal fabbricante del dispositivoVermont Casting EWF36A possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Vermont Casting
- manuali per l’uso EWF36A
- schede prodotto Vermont Casting
- opuscoli
- o etichette energetiche Vermont Casting EWF36A
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Vermont Casting EWF36A.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Vermont Casting EWF36A, manuali di manutenzione, brevi manuali o manuali utente Vermont Casting EWF36A. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Vermont Casting EWF36A.

Manuali per l’uso simili

Manuale completo del dispositivo Vermont Casting EWF36A, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Vermont Casting EWF36A dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Vermont Casting EWF36A.

Il manuale per l’uso completo Vermont Casting, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Vermont Casting EWF36A - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Vermont Casting EWF36A, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Vermont Casting EWF36A che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Vermont Casting EWF36A - che ci dovrebbe aiutare nei primi passi durante l'uso Vermont Casting EWF36A
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Vermont Casting EWF36A
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Vermont Casting EWF36A in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Vermont Casting EWF36A?

Utilizza il modulo sottostante

Se non hai risolto il problema con Vermont Casting EWF36A con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Vermont Casting EWF36A è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)