Italiano dropdown-ico

Manuale per l’uso Encore electronic ENNUS1

30 pagine 1.21 mb
Scarica

Vai alla pagina of 30

Summary
  • Encore electronic ENNUS1 - page 1

    ENNUS1 USB-OVER-NETWORK SERVER User Manual 0 ...

  • Encore electronic ENNUS1 - page 2

    Table of Contents CHAPTER1 INTRODUCTION .......................................................................................................... 2 CHAPTER2 PRODUCT OVER VIEW ............................................................................................... 3 2.1 Package Contents ....................................................... ...

  • Encore electronic ENNUS1 - page 3

    Chapter1 Introduction Thank you for purchasing Encore ENNU S1 USB-OVER -NETWORK SERVER (in the f o l l o w i n g r e f e r r e d t o a s “ E N N U S 1 S e r v e r ” ) . E N N U S 1 S e r v e r i s d e s i g n e d t o c o n n e c t your AIO/MFPs (All- In-One/Multifunction Pr inter), printers, USB mass stor ages (hard drives, flash driv es, and m ...

  • Encore electronic ENNUS1 - page 4

    Chapter2 Product Overview 2.1 Package Contents V erify that nothing is missing from the package by using the checking list below . Please contact your retailer if an y item is missing or damaged. All packing materials are recyclable. Please confirm the items in the package below:  The ENNUS1 USB-OVER -NETWORK SERVER  Quick Installation Guide ...

  • Encore electronic ENNUS1 - page 5

    Chapter3 Basic Installation 3.1 Connecting the Hardware 1. Make sure that y our USB devices ar e switched off and that the ENNUS1 Server’ s power adapter is disconnected. 2. Connect the USB devices to the USB ports. 3. Connect the ENNUS1 Server to the network with a twisted-pair category 5 cable, 10base T or 100base TX. 4. T urn on t he USB devic ...

  • Encore electronic ENNUS1 - page 6

    3.2.4 Server Names and Server Name Rules The default server name of the Serv er is “ENNUS1” . If you hav e multiple Servers in your local area network, to av oid using the same server names you hav e to change the server names by using t h e Control Center . If your serv er name is longer than 15 char acters, the Server uses only the first 15 c ...

  • Encore electronic ENNUS1 - page 7

    5. Click the “CONFIG” button and enter the ENNUS1 Serv er’s administrator (default: admin) and password (default: admin). 6. After you login successfully , the “general setting” web page appears. 6 ...

  • Encore electronic ENNUS1 - page 8

    7. Click the button corresponding to your ch oice of IP setting method (static or dynamic using DHCP). When assigni ng a static IP address you also have to define Subnet Mask and Default Gatew ay . If you choose Automatically get IP by DHCP , you can use desired DNS by c licking the Manual DNS button and manually assigning a DNS. 8. Click Submit to ...

  • Encore electronic ENNUS1 - page 9

    Chapter4 Using the ENNUS1 Server 4.1 Introduction The goal of this product is to provide connectivity to USB devices from a single serv er . A new technology , “NetUSB” , has been develo ped to achiev e this goal. “NetUSB” is a “USB over IP” technology that tr ansparen tly redirects all USB packets to a T CP/IP network channel. “NetUS ...

  • Encore electronic ENNUS1 - page 10

    Y ou must change the IP address (or using DHCP) of the ENNUS1 serv er so that the ENNUS1 server and y our PC are in the same subnet. T o do this, please double-click on the ENNUS1 server , and the following window will appear . Change the IP setting to make ENNUS1 serv er and your PC within the same subnet. After automatic reboot, Control Center wi ...

  • Encore electronic ENNUS1 - page 11

    C. When the installation progr am asks yo u to plug-in the USB device, run the “Control Center” . D. In the Control Center , click t he ENNUS1 server that has the desired USB device attached. E. Click the desired USB device as in the following figure. 10 F. Click the “Connect” button. Then the message “Manually Connect by your_computer_na ...

  • Encore electronic ENNUS1 - page 12

    4.5 Using the ENNUS1 Server A. In the Control Center , click the ENNUS1 server that has the desired USB device attached. B. Click the desired USB device. C. Click the “Connect” button. Then the message “Manually Connect by your_computer_name ” will appear . D. Now , the PC will detect the newly connect ed USB device. The “connect ” oper ...

  • Encore electronic ENNUS1 - page 13

    4.6 Auto-Connect Printer The method described in section 4.5 is called “manual connect” , which means users must manually connect and disconnect the US B device before and after using that device, otherwise nobody else can connect that device. However , for printers and scanners (and MFPs), the ENNUS1 serv er su pports auto-connect so users do ...

  • Encore electronic ENNUS1 - page 14

    The following window will appear . D. Choose the desired printer . The desired pr inter must be the Windows printer (this is a logical printer) that matches the prin ter attached on the ENNUS1 server (this is a physical printer). Then click the “ Apply” button. E. Then, the printer will be mark ed as an “ A uto-Connected Printer” in red. If ...

  • Encore electronic ENNUS1 - page 15

    F. T r y to issue a print job to the desired printer . The Cont rol Center will automatically do a connect operation. The print job will be issued to that printer . G. Even if you ha ve properly setup an auto -connected printer , the Control Center must be running (in the bac kground) while a print job is i ssued. This means you hav e to open the C ...

  • Encore electronic ENNUS1 - page 16

    C. Click the “Network Scanner” button. Then yo u can see that the Control Center will automatically do a “connect” operatio n. The following window will appear . D. Choose one of TWAIN or WIA item. Click “OK” . The following window will appear . 15 ...

  • Encore electronic ENNUS1 - page 17

    E. F o llow the usual steps to do scanning. F. After the scanning, close the “ Auto-Connect Sca nner” window . At this moment, Control Center will automa tically do a disconnect. 4.8 USB Storage When you connect a USB stor age, as in the fo llowing picture, a new disk will appear on your PC. If the USB stor age is a flash driv e, the new disk w ...

  • Encore electronic ENNUS1 - page 18

    Y ou can see the stor age ic on in the system tray . Use the new disk as a regular disk. When y ou are ready to disconnect the disk, click the stor age icon in the system tray an d choose “Safely remov e USB Mass Stor age Device” to remove the USB stor age, as the following figure. Open the Control Center , click the USB st orage device and cli ...

  • Encore electronic ENNUS1 - page 19

    At this moment, the user on the TEST1 computer will see the following window , indicating that another computer – TEST2 is requesting to use the HP printer . The user can choose to accept or reject. If accepted, the Control Center on TEST1 will automatically disconnect the device and the Control Center on TEST2 will automatically connect that dev ...

  • Encore electronic ENNUS1 - page 20

    Chapter5 The Control Center This chapter describes how to use the Control Center . 5.1 Installing Control Center 1. Insert the included CD into the personal computer. The Autorun screen as in the following should appear. 2. Click Install Application button. 3. Click Next to continue through ea ch installation step. 4. Click Finish . 19 ...

  • Encore electronic ENNUS1 - page 21

    5.2 Using the Control Center Y ou can use the following tools to help y ou use the ENNUS1 server:  Configure Server : go to the server’ s web pages to configure the highlighted ENNUS1 server .  Auto-Connect Printer : set auto-connect printer . Pl ease refer to section 4.6 for details.  Connect : connect a highlighted USB device.  Disc ...

  • Encore electronic ENNUS1 - page 22

    Chapter6 The ENNUS1 Server’s Web Pages 6.1 Introduction The ENNUS1 server runs the http server on T CP port: 80. Us ers may use the web pages to see the ENNUS1 Server’ s system status and configure the ENNUS1 Server . 6.2 Using the ENNUS1 Server’s Web Pages 6.2.1 Displaying ENNUS1 Server Status Click on the “ST A TUS” icon to see system s ...

  • Encore electronic ENNUS1 - page 23

    6.2.2 Setting up ENNUS1 Server Configuration T o set up the ENNUS1 Server configur ation, click on the “C ONFIG” icon and then the system will request user to enter administrator (default: admin ) and password (default: admin ) to login.  General Configuration  Server Information: Y ou hav e to set the Server Name, which is the name to re ...

  • Encore electronic ENNUS1 - page 24

     Maintenance If you want to restore factory default v alues of the ENNUS1 Server or upgr ade new firmware, you can use the Maintenance tool. 5 Restart: click “Y es” button to restart (reboot) the ENNUS1 Serv er . 5 Factory Default: click this button, the ENNUS1 Server will restore factory default values. 5 Download New Firmware: click this b ...

  • Encore electronic ENNUS1 - page 25

    24 ...

  • Encore electronic ENNUS1 - page 26

    Chapter7 Troubleshooting This chapter provides useful information to help yo u resolve diffic ulties that you ma y experience with your ENNUS1 Server . F aul t symptoms, possible causes, and remedial actions are provided within a quick reference table. This ENNUS1 Server’ s USB ports only support MFPs, printers, scanners, mass stor age, and USB c ...

  • Encore electronic ENNUS1 - page 27

    Chapter8 Restore Factory Defaults Y ou ma y restore the ENNUS1 Server’ s defa ult parameters by one of the following methods. 8.1 Using the ENNUS1 Server’s Web Pages 1. Go to the ENNUS1 Server ’ s web page and click CONFIG 2. Enter administra tor (default: admin ) and password (default: admin ). 3. Click Maintenance . 4. Click Factory Default ...

  • Encore electronic ENNUS1 - page 28

    8.3 Default Parameters List Server Information z Server Name: ENNUS1 TCP/IP z Automatically get IP by DHCP: Enabled - Manual DNS: None (Disabled) . z Static IP: Disabled - IP Address: 192.168.1.100 - Subnet Mask: 255.255.255.0 - Default Gateway: none - DNS Server: none User Accounts z Administrator: admin z Password: admin 27 ...

  • Encore electronic ENNUS1 - page 29

    Chapter9 Upgrade Firmware This chapter describes how to upgrade firm w are. Please follow one of the following methods: Method A: Using the ENNUS1 Server’s Web Pages Please refer to section 6.2.2 for details. Method B: Using the Init Button and the TFTP Client 1. Plug in the power adaptor while pre ssing the Init button until the USB LED blinks. ...

  • Encore electronic ENNUS1 - page 30

    Chapter10 The Init Button The Init button is used for maintenance: Simultaneously press Init button and turn on (by plugging in the power adaptor) th e ENNUS1 Server until the USB LED blinks. The ENNUS1 Server will now do the following tasks: A. P erform a factory reset of the ENNUS1 serv er , which restores most of the par a meters and settings to ...

Fabbricante Encore electronic Categoria Server

I documenti che otteniamo dal fabbricante del dispositivoEncore electronic ENNUS1 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Encore electronic
- manuali per l’uso ENNUS1
- schede prodotto Encore electronic
- opuscoli
- o etichette energetiche Encore electronic ENNUS1
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Encore electronic ENNUS1.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Encore electronic ENNUS1, manuali di manutenzione, brevi manuali o manuali utente Encore electronic ENNUS1. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Encore electronic ENNUS1.

Manuali per l’uso simili

Manuale completo del dispositivo Encore electronic ENNUS1, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Encore electronic ENNUS1 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Encore electronic ENNUS1.

Il manuale per l’uso completo Encore electronic, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Encore electronic ENNUS1 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Encore electronic ENNUS1, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Encore electronic ENNUS1 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Encore electronic ENNUS1 - che ci dovrebbe aiutare nei primi passi durante l'uso Encore electronic ENNUS1
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Encore electronic ENNUS1
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Encore electronic ENNUS1 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Encore electronic ENNUS1?

Utilizza il modulo sottostante

Se non hai risolto il problema con Encore electronic ENNUS1 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Encore electronic ENNUS1 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)