Italiano dropdown-ico

Manuale per l’uso Pelco ES31PC

68 pagine 0.45 mb
Scarica

Vai alla pagina of 68

Summary
  • Pelco ES31PC - page 1

    ES30PC/ES31PC Esprit ® with Pressurized IOC C311M-L (1/05) ® INST ALLA TION/OPERA TION U.S. Patent D-472.260 ...

  • Pelco ES31PC - page 2

    2 C311M-L (1/05) CONTENTS Section Page IMPORT ANT SAFETY INSTRUCTIONS .................................................................................................. ............................................................................. 5 DESCRIPTION ......................................................................................... ...

  • Pelco ES31PC - page 3

    C311M-L (1/05) 3 GAIN/AGC ................................................................................................................................................................................................................ 34 IR FIL TER MODE (MODELS ES30PCBW18/ES31PCBW18 ONL Y) ........................................................... ...

  • Pelco ES31PC - page 4

    4 C311M-L (1/05) ...

  • Pelco ES31PC - page 5

    C311M-L (1/05) 5 IMPORT ANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other ...

  • Pelco ES31PC - page 6

    6 C311M-L (1/05) DESCRIPTION The ES30PC/ES31PC Esprit Series is designed to protect camera optics and electronics from moisture and airborne contaminants. The system features a receiver , pan and tilt, enclosure, and a pressurized integrated optics cartridge (IOC). The integrated optics cartridge packages an auto focus camera, lens, heater , and se ...

  • Pelco ES31PC - page 7

    C311M-L (1/05) 7 INST ALLA TION  When installing the ES30PC/ES31PC Esprit ® system, allow for sufficient clearance between the top of the unit and overhead obstructions. This will prevent interference when the enclosure is driven to its maximum elevation of 33 degrees.  Remove the transformer module from the base of the system by loosening t ...

  • Pelco ES31PC - page 8

    8 C311M-L (1/05)  Route the wires and cables through the center of the Esprit mount. Reinstall the transformer module into the base. The transformer module can be positioned in the mount base in only one orientation.  ES30PC-5/ES31PC-5 Models Only – Set the 120/230 voltage selector switch on the transformer to the appropriate voltage.  C ...

  • Pelco ES31PC - page 9

    C311M-L (1/05) 9  Tu rn on the power . If the red LED lights, turn off the power and proceed to the next step. If the red LED does not light, refer to the Tr oubleshooting section.  Plug the male Esprit system connector , located on the bottom of the pan and tilt, into the female Esprit system connector locat ed on the transformer module. Ali ...

  • Pelco ES31PC - page 10

    10 C311M-L (1/05) TXB SERIES TRANSLA TOR BOARD INST ALLA TION (OPTIONAL) Pelco’ s TXB Series allows controllers from other companies to communicate with the Esprit system. To install a TXB Series board, remove the left cover of the pan and tilt. Once the cover is removed, refer to the manual supplied with the translator board to complete the inst ...

  • Pelco ES31PC - page 11

    C311M-L (1/05) 11 HOW TO REINST ALL THE PAN AND TIL T COVER The pan and tilt covers must be properly seated and have a tight seal all the way around when installed. To reinstall the pan and tilt cover , do the following: 1. Properly position the cover and slide it into place. The sides of the cover must fit under the front and back rain guards of t ...

  • Pelco ES31PC - page 12

    12 C311M-L (1/05) OPERA TION POWER-UP DISPLA Y When the system is powered up, the selected protocol, revision number , and other information is displayed on the monitor . For e xample, the screen might show the following information: The information displayed depends on the selected protocol (C, D, or P) and the menu selection for power - up mode. ...

  • Pelco ES31PC - page 13

    C311M-L (1/05) 13 PRESSURIZED INTEGRA TED OPTICS CARTRIDGE The pressurized IOC houses an auto focus camera, lens, heater , and sensors in a self-contained, sealed unit. Dry nitrogen pressurized to 10 psig controls the environment inside the cartridge, eliminating internal condensation and corrosion. Sensors strategically placed inside the pressuriz ...

  • Pelco ES31PC - page 14

    14 C311M-L (1/05) CURRENT READING MENU The Current Reading menu displays the existing status of temperature, pressure, and dewpoint inside the integrated optics cartridge. An asterisk displayed to the left of a menu item denotes that an alert condition exists. Due to the heat emitted from the electronics of the camera, normal temperature operating ...

  • Pelco ES31PC - page 15

    C311M-L (1/05) 15 ZONES A zone is a programmed pan area with set boundaries and identifying label. The Esprit system has a maximum of eight zones, each with a 20-character label. Zones can be programmed to blank video when the camera pans into the zone area. If a zone is blanked, the system displays the message, VIDEO BLANK. (Refer to Zone Blank in ...

  • Pelco ES31PC - page 16

    16 C311M-L (1/05) PROGRAMMING – ES30PC16/ES31PC16 Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Line Sync On Line Sync Phase 0 Exit Line Sync Menu Power Up Default Exit Power -Up Menu Wiper Mode Momentary Wiper Dwell <s> 2 Wiper T ime <m> 60 Exit *Wiper Menu Limit Stops Off Se ...

  • Pelco ES31PC - page 17

    C311M-L (1/05) 17 PROGRAMMING – ES30PC22/ES31PC22 Gain Limit 7 Exit Gain/AGC Menu Auto-iris mode Auto Auto-iris level 66 Auto-iris peak 16 Exit Auto Iris Menu LowLight limit 2 Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance> Prev Exit Next Menu Auto Sharpness On Sharpness 13 Exit Sharpness Menu Auto white bal On R-G ...

  • Pelco ES31PC - page 18

    18 C311M-L (1/05) PROGRAMMING – ES30PCBW18/ES31PCBW18 Gain Limit 28 Exit Gain/AGC Menu Auto-iris mode Auto Auto-iris level 91 Auto-iris peak 16 Exit Auto Iris Menu LowLight limit 2 Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Prev Exit Next Menu Auto Sharpness Sharpness On Exit Sharpness Menu I ...

  • Pelco ES31PC - page 19

    C311M-L (1/05) 19 PROGRAMMING ACCESSING MAIN MENU (PRESET 95) Y ou can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 for Pelco’ s controllers varies according to the type of controller you are using. Instructions for progra mming preset 95 are given below for ...

  • Pelco ES31PC - page 20

    20 C311M-L (1/05) ACK ACT (ACKNOWLEDGE ACTION) If an enivornmental condition inside of the IOC goes outside of the factory set limits (such as “Low Pressure”) then select ACK Alert to activate the alert label behavior . Program ACK Act to establish alert label behavior after alert acknowledgement. The following acknowledge actions are available ...

  • Pelco ES31PC - page 21

    C311M-L (1/05) 21 ALERT DISPLA Y POSITION Screen positioning of the alert label is user -defined. Positioning options include the following: To set the alert label position: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Alert. 3. Press the Iris Open button to enter the Alert menu. 4. Position the cursor (> ...

  • Pelco ES31PC - page 22

    22 C311M-L (1/05) ALERT REPEA T Y ou can program how often an ALERT label is repeatedly displayed until it is acknowledged by the system controller . The followi ng settings are available: Constant The ALERT label is continually displayed on the monitor until acknowledged. 15 min off The ALERT label is displayed every 15 minutes for a 15-second dur ...

  • Pelco ES31PC - page 23

    C311M-L (1/05) 23 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu LowLight limit Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance& ...

  • Pelco ES31PC - page 24

    24 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Auto-iris mode Auto Auto-iris level Auto-iris peak Exit Auto Iris Menu AUTO IRIS The follow ...

  • Pelco ES31PC - page 25

    C311M-L (1/05) 25 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu LowLight limit Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness ...

  • Pelco ES31PC - page 26

    26 C311M-L (1/05) AUTO SHARPNESS <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu LowLight limit Auto Shutter speed Auto Auto focus mode Auto <Sharpness> ...

  • Pelco ES31PC - page 27

    C311M-L (1/05) 27 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile <Zone Blank> <Az/El/Direction> Exit Other Menu Az/El/Direction Set Azimuth Zero Az/El Az/ ...

  • Pelco ES31PC - page 28

    28 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile <Zone Blank> <Az/El/Direction> Exit Other Menu Set Azimuth Zero Az/El Az/El Line Directio ...

  • Pelco ES31PC - page 29

    C311M-L (1/05) 29 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile <Zone Blank> <Az/El/Direction> Exit Other Menu Az/El/Direction Set Azimuth Zero Az/El Az/ ...

  • Pelco ES31PC - page 30

    30 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu NON-SENSITIVE AREA SENSITIVE AREA BACKLIGHT COMPENSA TION There are two backlight compensat ...

  • Pelco ES31PC - page 31

    C311M-L (1/05) 31 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile <Zone Blank> <Az/El/Direction> Exit Other Menu Az/El/Direction Set Azimuth Zero Az/El Az/ ...

  • Pelco ES31PC - page 32

    32 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile <Zone Blank> <Az/El/Direction> Exit Other Menu Az/El/Direction Set Azimuth Zero Az/El Az/ ...

  • Pelco ES31PC - page 33

    C311M-L (1/05) 33 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile <Zone Blank> <Az/El/Direction> Exit Other Menu Az/El/Direction Set Azimuth Zero Az/El Az/ ...

  • Pelco ES31PC - page 34

    34 C311M-L (1/05) GAIN LIMIT The gain limit sets the maximum level for the automatic gain control. Increasing the level will increase the signal level and increase the noise level of the picture. To change the gain: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter ...

  • Pelco ES31PC - page 35

    C311M-L (1/05) 35 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu LowLight limit Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness ...

  • Pelco ES31PC - page 36

    36 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Limit Stops Off Set Man Limits Clear Man Limits Set Scan Limits Clear Scan Limits Exit Limit Stop Menu LIMIT STOPS NOTE: Limit stops are inactive while setting items in the program menu (e.g. azim ...

  • Pelco ES31PC - page 37

    C311M-L (1/05) 37 LIMIT STOPS MENU The manual pan limit stops can be set at the controller using the Limit Stops menu: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3. Press the Iris Open button to enter the Limit Stop menu. 4. Move the cursor to Set Man Limits and press the Iris Open button. PRE ...

  • Pelco ES31PC - page 38

    38 C311M-L (1/05) Scan Limit Stops When scan limit stops are set, the pan and tilt reverses direction during random, frame, or auto scanning when a limit stop is reached. The manual scan limit stops can be set in one of two ways: At the controller by programming presets 92 and 93 or At the controller by programming the Limit Stops menu PRESETS Refe ...

  • Pelco ES31PC - page 39

    C311M-L (1/05) 39 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Line Sync On Line Sync Phase 0 Exit Line Sync Menu LINE SYNCHRONIZA TION If cameras are out of phase with each other , they may produce what appears to be vertical roll when switching between came ...

  • Pelco ES31PC - page 40

    40 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu LowLight limit Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance& ...

  • Pelco ES31PC - page 41

    C311M-L (1/05) 41 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 90 MPH wind Exit Other Menu P ARK TIME MINUTES This feature causes the system to park at preset 1 aft ...

  • Pelco ES31PC - page 42

    42 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 90 MPH wind Exit Other Menu PA TTERN LENGTH The Esprit can do the following: One full pattern - 1.5, ...

  • Pelco ES31PC - page 43

    C311M-L (1/05) 43 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Power Up Default Exit Power -Up Menu POWER-UP MODE This feature lets the dome resume a desired condition following power -up. The menu includes the following choices. • Default – On power -up, ...

  • Pelco ES31PC - page 44

    44 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 50 MPH wind Exit Other Menu PROPORTIONAL P AN There are two proportional pan modes: On – Enables th ...

  • Pelco ES31PC - page 45

    C311M-L (1/05) 45 Default Setting <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu RESET CAMERA Resetting the camera returns the settings to their defaults. M ...

  • Pelco ES31PC - page 46

    46 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 50 MPH wind Exit Other Menu SCAN SPEED The scan speed is adjustable from 1-40 degrees per second. Thi ...

  • Pelco ES31PC - page 47

    C311M-L (1/05) 47 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu LowLight limit Auto Shutter speed Auto Auto focus mode Auto <Sharpness> <White bal ...

  • Pelco ES31PC - page 48

    48 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu LowLight limit Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance& ...

  • Pelco ES31PC - page 49

    C311M-L (1/05) 49 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 50 MPH wind Exit Other Menu SPEED PROFILE This feature allows the operator to set the wind speed cond ...

  • Pelco ES31PC - page 50

    50 C311M-L (1/05) Auto white bal On Red bal level 182 Blue bal level 182 Exit White Balance Menu <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu LowLight lim ...

  • Pelco ES31PC - page 51

    C311M-L (1/05) 51 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Wiper Mode Momentary Wiper Dwell <s> 2 Wiper T ime <m> 60 Exit Wiper Menu WIPER MODE There are three wiper settings: Wiper Mode Wiper Dwell Wiper T ime To change the wiper settings: 1. ...

  • Pelco ES31PC - page 52

    52 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 90 MPH wind <Zone Blank> Exit Other Menu Video Blank Zone 1 Off 2 Off 3 Off 4 Off 5 Off 6 Off 7 ...

  • Pelco ES31PC - page 53

    C311M-L (1/05) 53 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile <Zone Blank> <Az/El/Direction> Exit Other Menu Set Azimuth Zero Az/El Az/El Line Directio ...

  • Pelco ES31PC - page 54

    54 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu ZOOM LIMIT ES30PC16/ES31PC16 – 16X optical zoom and 10X electronic zoom ES30PC22/ES31PC22 ...

  • Pelco ES31PC - page 55

    C311M-L (1/05) 55 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile <Zone Blank> <Az/El/Direction> Exit Other Menu Set Azimuth Zero Az/El Az/El Line Directio ...

  • Pelco ES31PC - page 56

    56 C311M-L (1/05) TROUBLESHOOTING NOTE: The system contains no user -serviceable parts. If there is a problem with your system, it must be returned to Pelco for servicing. Symptom: System does not operate. 1. Check system input voltage. 2. The Esprit system is protected by a resettable overcurrent protective device located in the transformer module ...

  • Pelco ES31PC - page 57

    C311M-L (1/05) 57 Symptom: No video or poor video 1. Check the video and power connections to the camera. 2. Check for power to the camera from the Esprit system camera power output. 3. Check all coax BNC connectors from the camera to the monitor . 4. Make sure the controller is set for the correct camera-to-monitor viewing combination; for example ...

  • Pelco ES31PC - page 58

    58 C311M-L (1/05) MAINTENANCE Clean the enclosure window periodically with a mild non-abrasive detergent in water and a soft cloth to help maintain picture clarity . If operating problems are experienced with the system, refer to the T roubleshooting section. WIPER If the window wiper assembly is installed, replace worn or deteriorated wiper blades ...

  • Pelco ES31PC - page 59

    C311M-L (1/05) 59 00864 2. Open hinge door to the system. Remove the cap screw that secures the wiper board. Unplug the ribbon cable connector . 00866 RIBBON CABLE CONNECTO R CAP SCREW 00865 3. Lift up wiper board and unplug the cartridge power cables. Let board dangle to the side of the enclosure. 4. Lift cartridge out of the enclosure. 00867 PRES ...

  • Pelco ES31PC - page 60

    60 C311M-L (1/05) APPENDIX NOTE: Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode. Therefore, the DIP switch settings have no effect on Coaxitron control signals. Table A. Switch Settings for SW1 Switch Setting Baud Rate SW1-1 SW1-2 SW1-3 2400 OFF OFF OFF* 4800 ON OFF OFF* 9600 ...

  • Pelco ES31PC - page 61

    C311M-L (1/05) 61 Table B. Switch Settings for SW2 NOTE: The Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode. Therefore, the DIP switches settings have no effect on Coaxitron control signals. Receiver Address Switch Setting P-T ype D-T ype Control Control SW2-1 SW2-2 SW2-3 SW2- ...

  • Pelco ES31PC - page 62

    62 C311M-L (1/05) Table B. Switch Settings for SW2 (Continued) (Continued on next page) Receiver Address Switch Setting P-T ype D-T ype Control Control SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 – 112 OFF OFF OFF OFF ON ON ON OFF – 113 ON OFF OFF OFF ON ON ON OFF – 114 OFF ON OFF OFF ON ON ON OFF – 115 ON ON OFF OFF ON ON ON OFF – 11 ...

  • Pelco ES31PC - page 63

    C311M-L (1/05) 63 Table B. Switch Settings for SW2 (Continued) Receiver Address Switch Setting P-T ype D-T ype Control Control SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 – 232 OFF OFF OFF ON OFF ON ON ON – 233 ON OFF OFF ON OFF ON ON ON – 234 OFF ON OFF ON OFF ON ON ON – 235 ON ON OFF ON OFF ON ON ON – 236 OFF OFF ON ON OFF ON ON ON ...

  • Pelco ES31PC - page 64

    64 C311M-L (1/05) SPECIFICA TIONS ELECTRICAL Input V oltage: 24, 120, or 230 V AC, 50/60 Hz; switch selectable for 120/230 VAC inputs. Reset featur e enabled when power becomes unstable or interrupted. Power Requirements: Maximum power consumption is 70 V A per system Heater and Defroster: Thermostatically controlled heater consumes 10 watts and cy ...

  • Pelco ES31PC - page 65

    C311M-L (1/05) 65 Sensitivity ES30PC16/ES31PC16: 0.05 lux at 1/2-second shutter speed (NTSC) 0.05 lux at 1/1.5-second shutter speed (P AL) ES30PC22/ES31PC22: 0.02 lux at 1/2-second shutter speed (NTSC) 0.02 lux at 1/1.5-second shutter speed (P AL) ES30PCBW18/ES31PCBW18: 0.08 lux at 1/2-second shutter speed (color , NTSC/P AL) 0.3 lux at 1/1.5-secon ...

  • Pelco ES31PC - page 66

    66 C311M-K (9/04) ...

  • Pelco ES31PC - page 67

    REVISION HISTORY Manual # Date Comments C311M 6/01 Original version. C311M-A 8/02 Camera modifications. C311M-B 9/02 Revised per ECO #02-8063. C311M-C 11/02 Revised installation instructions for addition of alignment label. C311M-D 6/03 Added Az/El/Direction menu per ECO #03-8861. Updated to new format. C311M-E 8/03 Revised per ECO #03-9210 for new ...

  • Pelco ES31PC - page 68

    W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 ® United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...

Fabbricante Pelco Categoria Security Camera

I documenti che otteniamo dal fabbricante del dispositivoPelco ES31PC possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Pelco
- manuali per l’uso ES31PC
- schede prodotto Pelco
- opuscoli
- o etichette energetiche Pelco ES31PC
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Pelco ES31PC.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Pelco ES31PC, manuali di manutenzione, brevi manuali o manuali utente Pelco ES31PC. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Pelco ES31PC.

Manuali per l’uso simili

Manuale completo del dispositivo Pelco ES31PC, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Pelco ES31PC dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Pelco ES31PC.

Il manuale per l’uso completo Pelco, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Pelco ES31PC - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Pelco ES31PC, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Pelco ES31PC che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Pelco ES31PC - che ci dovrebbe aiutare nei primi passi durante l'uso Pelco ES31PC
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Pelco ES31PC
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Pelco ES31PC in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Pelco ES31PC?

Utilizza il modulo sottostante

Se non hai risolto il problema con Pelco ES31PC con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Pelco ES31PC è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)