-
Epson C82310 - page 1
EPSON 32KB Parallel Interface Card C82310 * English Deutsch Français Español Italiano 4000402 S01-00 ...
-
Epson C82310 - page 2
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a Class B digita1 device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radi ...
-
Epson C82310 - page 3
32KB Parallel Interface Card C82310* 32-KB-Schnittstellenkarte C82310* Carte d’Interface parallèle 32Ko C82310* Módulo de interface en paralelo de 32KB C82310* Scheda dell’interfaccia parallela da 32KB C82310* ...
-
Epson C82310 - page 4
TABLE OF CONTENTS INTRODUCTION About this guide SETTING THE CONDITIONS Card layout DIP switch and jumper settings DIP switches Jumpers DATA ENTRY About data entry SELF TEST SPECIFICATIONS HARDWARE DESCRIPTION INSTALLATION 2 3 4 4 5 5 7 9 9 10 11 12 15 1 ...
-
Epson C82310 - page 5
INTRODUCTION The Parallel Interface C82310* is an interface card that allows parallel data communication between a host computer and an Epson printer. This card has the following features: Ž A 32 Kbyte buffer that frees up your computer for other uses while your printer continues to print Ž A self-test function that can help solve interface probl ...
-
Epson C82310 - page 6
About this guide This guide tells you how to install your C82310* interface card in a variety of Epson printers. Also included are instructions on how to adjust the settings of the C82310* interface card, as well as a general description of parallel data communication. The C82310* option package contains the following items: C82310 * parallel l/F C ...
-
Epson C82310 - page 7
SETTING THE CONDITIONS The C82310* interface card has two sets of DIP switches, and five jumpers. These switches and jumpers are used for selecting various interface operations. Card layout The figure below shows the layout of the C82310* card and the locations of the DIP switches and jumpers. Figure 2. Card layout 4 ...
-
Epson C82310 - page 8
DIP switch and jumper settings Before you install the C82310* interface, you may need to adjust DIP switch 1 and jumper settings. You can change switch 2 settings after you install the interface. When making DIP-switch setting changes, use a pointed device such as a ball-point pen or small screwdriver. Caution Always turn the power off before chang ...
-
Epson C82310 - page 9
DIP switch 1 (interface operations) The table below contains information on switch func- tions, and the factory setting of each switch. Table 1. DIP switch 1 Note When DIP switch l-l is set to ON, the interface card can continue store data in the buffer memory even though the printer is in an OFF LINE or PAUSE state. Switch 2 The table below contai ...
-
Epson C82310 - page 10
Some printers have a switch (or function) that allows you to select between the optional and original interface. If you install the C82310* interface card in this type of printer, set the interface card’s DIP switch 2 to ON and also change the setting in the printer to select the optional interface. Jumpers A jumper is a small plug used for conne ...
-
Epson C82310 - page 11
The tables below describe the interface conditions that can be selected using jumpers. In all cases, ON means you connect the jumper (cover both terminals), while OFF means you disconnection of the jumper. Table 3. Jumper settings Jumper Function Factory setting J1 Fixed (See Note) J2 Fixed (See Note) J3 Fixed (See Note) J4 Fixed (See Note) JG ON: ...
-
Epson C82310 - page 12
DATA ENTRY About data entry For quick data entry, the C82310* interface card is equipped with a buffer that temporarily stores data before it is printed. When this buffer becomes full, the interface card send a BUSY signal . (Reception of data during this state cannot be guaranteed.) The data in the buffer is automatically sent to the printer when ...
-
Epson C82310 - page 13
SELF TEST You can run the self test by first turning off the printer and then turning on DIP switch l-3. When you turn the power back on, the self test begins. To exit from the self test, turn off the power and turn DIP switch 1-3 off. The interface card first checks the RAM condition. After checking the RAM, data from <30>H to <39>H is ...
-
Epson C82310 - page 14
SPECIFICATIONS 1. Data transmission: 8-bit parallel 2. Synchronization: External supplied STROBE pulse 3. Handshaking: Via ACKNLG or BUSY signals 4. Logic level: TTL level 5. RAM capacity: 32 Kbytes 6. Connector: 57-30360 (Amphenol), 36 pin or its equivalent Interface timing The figure below shows the timing for the parallel interface. Figure 3. In ...
-
Epson C82310 - page 15
HARDWARE DESCRIPTION For signal description and pin assignment, refer to the table below: Table 5. Signal description and pin assignment Signal Return Pin Pin 1 2 3 4 5 6 7 8 9 10 11 12 19 20 21 22 23 24 25 26 27 28 Signal STROBE DATA 1 IN DATA 2 IN DATA 3 IN DATA 4 IN DATA 5 IN DATA 6 IN DATA 7 IN DATA 8 IN ACKNLG OUT BUSY OUT PE OUT Direction IN ...
-
Epson C82310 - page 16
Signal Pin Return Signal Direction Pin Description SLCT AUTO FEED XT NC GND CHAS- SIS GND NC GND INIT OUT IN IN A high signal indicates that the printer is in the selected state. The signal goes low in the following cases: 1) When the SLCT IN signal goes high 2) During a printer-error state 3) When the interface card is disabled This signal can be ...
-
Epson C82310 - page 17
Signal Return Pin Pin Signal 35 36 Direction OUT SLCT IN IN Description Pulled up to +5 V through 3.3 K W resistance. The DC1/DC3 code are valid only when this signal is high. (This signal can be fixed low by changing a DIP switch, jumper, or SelecType setting on the printer.) The printer monitors this signal, so this signal’s function depends on ...
-
Epson C82310 - page 18
INSTALLATION Installation or removal of the C82310* interface card is easy, and requires only a screwdriver. The following section tells you how to install your interface card in a variety of EPSON printers. Caution • Turn off the power to the printer and the computer before installing. Make sure that all power and interface cables are removed. ? ...
-
Epson C82310 - page 19
3. Insert firmly until the interface pins mate with connector inside your printer. 4. Attach the two screws to secure the interface. 16 ...
-
Epson C82310 - page 20
EPSON OVERSEAS MARKETING LOCATIONS EPSON AMERICA, INC. 20770 Madrona Avenue Torrance CA 90503, USA Phone: (213) 782-0770 Fax: (213) 782-5248 EPSON UK LTD. Campus 100, Maylands Avenue Hemel Hempstead Herts. HP2 7EZ, UK Phone: 442-61144 Telex: 5182467 EPSON AUSTRALIA PTY. LTD. UNIT 3, 17 Rodborough Road Frenchs Forest, NSW 2086, Australia Phone: (2) ...
-
Epson C82310 - page 21
EPSON Printed in Japan 91.03-2 ...
Hai una domanda su Epson C82310?
Utilizza il modulo sottostante
Se non hai risolto il problema con Epson C82310 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Epson C82310 è probabile che voglia condividere il modo di risolverlo.