-
Perlick H50IMS-ADR - page 1
MODELS: H50IMS-R H50IMS-L H50IMW H50IMS-ADL H50IMS-ADR H50IMW-AD PERLICK SELF-CONTAINED ICE MAKER P R O D U C T M A N U A L Issued: 11-2-2009 ...
-
Perlick H50IMS-ADR - page 2
2 IMPORTANT This manual should be read carefully before the icemaker is installed and operated. Only qualied service technicians should install, service, and maintain the icemaker. Read the warnings contained in this booklet carefully as they give important information regarding safety. Please retain this booklet for any further reference that m ...
-
Perlick H50IMS-ADR - page 3
3 Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, or damage to the unit. WARNING Indicates a hazardous situation which could result in death or serious injury. CAUTION Indicates a situation which could result in damage to the unit. IMPORTANT Indic ...
-
Perlick H50IMS-ADR - page 4
4 I. Specications A. Construction Top Panel Ice Making Mechanism Scoop Holder Front Panel Control Switch Louver Bin Control Thermostat Bulb Slope Magnet Catch Door Power Cord ...
-
Perlick H50IMS-ADR - page 5
5 PERLICK ICE MAKER MODEL NUMBER H50IMS-R SERIAL NUMBER AC SUPPLY VOLTAGE 115-120/60/1 AMPERES 3.4 AMPS DESIGN PRESSURE HI-240PSI LO-120PSI REFRIGERANT 134a 4.2 oz. B. Nameplate Rating See the nameplate for electrical and refrigeration specications. This nameplate is located inside the bin on the right side. We reserve the right to make changes ...
-
Perlick H50IMS-ADR - page 6
6 Units: mm [in.] C. Dimensions/Connections 1. H50IMS-R, H-50IMS-L ...
-
Perlick H50IMS-ADR - page 7
7 2. H50IMW Units: mm [in.] ...
-
Perlick H50IMS-ADR - page 8
8 3. H50IMS-ADL, H50IMS-ADR Units: mm [in.] ...
-
Perlick H50IMS-ADR - page 9
9 4. H50IMW-AD Units: mm [in.] ...
-
Perlick H50IMS-ADR - page 10
10 II. Installation and Operating Instructions WARNING 1. This icemaker must be installed in accordance with applicable national, state, and local regulations. 2. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin. A. Checks Before Installa ...
-
Perlick H50IMS-ADR - page 11
11 2. Built-In Installation Site CAUTION 1. Do not let the weight of the counter rest on the icemaker. 2. Do not install the icemaker in a corner where the door will interfere with other equipment or where the icemaker cannot be pulled out for service. Installation Space Model Height Width Depth H50IMS-R/L H50IMW 34" (864 mm) minimum 15" ...
-
Perlick H50IMS-ADR - page 12
12 1 2 3 4 6 5 C. D oo r Ov er la y P an el F ab ri ca ti o n an d At ta ch me nt (H 50 IM W, H 50 IM W- AD) IMPORTANT The overlay panel must be crafted by a professional cabinet maker to ensure quality results. (1) Parts Ensure that all parts required for the overlay panel assembly are contained in the accessories bag. Overlay Panel Parts No. Desc ...
-
Perlick H50IMS-ADR - page 13
13 (2) Overlay Panel Specification Use the specication that applies to your icemaker (H50IMW or H50IMW-AD) and the directions that follow to prepare your overlay panel. (a) H50IMW H50IMW Overlay Panel Specication Overlay Panel Height 29 17/32" (750 mm) Overla ...
-
Perlick H50IMS-ADR - page 14
14 H50IMW-AD Overlay Panel Specication Overlay Panel Height 27 9/16" (700 mm) Overlay Panel Width 14 13/16" (376 mm) Overlay Panel Thickness 5/8" (16 mm) minimum; 3/4" (19 mm) maximum Overlay Panel and Door Weight (total) 20 lb. (9 kg) maximum (b) ...
-
Perlick H50IMS-ADR - page 15
15 3) Screw the 6 threaded wood inserts into the 1/4" holes drilled in the previous step. Make sure that the inserts are threaded straight and that the tops of the inserts are ush to the overlay panel surface. Otherwise, the overlay panel cannot be properly fastened to the door. 4) Mount the door handle hardware. Perlick recommends that the ...
-
Perlick H50IMS-ADR - page 16
16 Screws f) Remove hinge (C1) from the top right part of the door, ip it and reattach to the bottom left. Remove hinge (C2) from the bottom right part of the door, ip it and reattach to the top left. See Fig. 8. Proceed to step 7. d) Remove hinge (B) from the right side of the unit and the 2 ller screws from the left side. Attach the 2 ? ...
-
Perlick H50IMS-ADR - page 17
17 9) Temporarily fasten the overlay panel to the door using 2 of the M4×25 pan head screws provided. See Fig. 11. CAUTION Ensure that the back surface of overlay panel is at before attaching. 10) Mark the centerpoint of the hinge (C1) and hinge (C2) holes that extend over the overlay panel. See Fig. 12. 7) Remove the bushings from hinge (C1) a ...
-
Perlick H50IMS-ADR - page 18
18 Snug the screws, but do not tighten. Sheet Metal Bracket Overlay Panel Tighten the screws. 5) Fasten the overlay panel to the door using the four M4×25 pan head screws provided. Snug the screws, but do not tighten. See Fig. 17. 6) Fasten the sheet metal bracket to the bottom of the door with the three T2 screws provided. Tighten the screws to t ...
-
Perlick H50IMS-ADR - page 19
19 7) Tighten the four M4×25 pan head screws installed in step 5. See Fig. 19. 8) Replace the door gasket in its proper orientation. Reinsert the bushings into hinge (C1) and hinge (C2) (the hinges attached to the door). See Fig. 20. Canoe Clips Fig. 19 Tighten the screws. Bushing Bushing Gasket Fig. 20 9) Attach the door to hinge (A), then contin ...
-
Perlick H50IMS-ADR - page 20
20 D. Setup 1) Position the icemaker in the selected permanent location. 2) Level the icemaker from side-to-side and front-to-rear by adjusting the feet. E. Electrical Connection WARNING 1. Electrical connection must meet national, state, and local electrical code requirements. Failure to meet these code requirements could result in death, electric ...
-
Perlick H50IMS-ADR - page 21
21 F. Water Supply and Drain Connections WARNING 1. Water supply and drain connections must be installed in accordance with applicable national, state, and local regulations. 2. Normal operating water temperature should be within 45°F to 95°F (7°C to 35°C). Operation of the icemaker, for extended periods, outside of this normal temperature rang ...
-
Perlick H50IMS-ADR - page 22
22 G. Final Checklist WARNING CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin. 1) Is the icemaker level? 2) Is the icemaker in a site where the ambient temperature is within 45°F to 100°F (7°C to 38°C) and the water temperature withi ...
-
Perlick H50IMS-ADR - page 23
23 H. Startup WARNING 1. All parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty coverage. 2. If the icemaker is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor. 3. At startup, conrm that all internal and external connec ...
-
Perlick H50IMS-ADR - page 24
24 III. Cleaning and Maintenance WARNING 1. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after any cleaning or maintenance is done to the unit. Make sure that none have fallen into the storage bin. 2. The storage bin is for ice use only. Do not store anything else in the storage bin. 3. Keep the area aroun ...
-
Perlick H50IMS-ADR - page 25
25 3) Inside the storage bin, disconnect the suction tube by squeezing the tabs and pulling the tube clear. See Fig. 26. Allow the water tank to drain. 4) Reconnect the suction tube as illustrated. See Fig. 27. Make sure the tabs lock into place; a loose tting may cause a water leak. 5) Slowly pour the cleaning solution into the water tank. 6) M ...
-
Perlick H50IMS-ADR - page 26
26 3. Sanitizing Solution IMPORTANT For safety and maximum effectiveness, use the solution immediately after dilution. Dilute 0.5 . oz. (14.8 ml or 1 tbs) of a 5.25% sodium hypochlorite solution (chlorine bleach) with 1 gallon (3.8 l) of warm water. This is a minimum amount. Make more solution if necessary. Using a chlorine test strip or other m ...
-
Perlick H50IMS-ADR - page 27
27 Reducing Pipe Rail Rail 13) Position and lock the ice chute onto the front and rear frame pipes by pushing the ice chute down until it clicks onto both frame pipes. See Fig. 36. 14) Slide in the water tank along the rails at the bottom of the left and right brackets until it locks into place. See Fig. 37. Right Bracket Rail Rail Fig. 34 Fig. 35 ...
-
Perlick H50IMS-ADR - page 28
28 15) Reconnect the suction tube. 16) Hook each separator onto the rail, then pull it hard towards you until it locks into place. See Fig. 38. 17) Replace the slope in its correct position. See Fig. 39. Fig. 38 18) Discard the sanitizing solution. 19) Mix a new batch of the sanitizing solution and slowly pour it into the water tank. 20) Move the c ...
-
Perlick H50IMS-ADR - page 29
29 B. Maintenance IMPORTANT This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. 1. Stainless Steel Exterior To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth. Use a damp cloth containing a neutral cleaner to wipe off oil or dirt build up. 2. Storage ...
-
Perlick H50IMS-ADR - page 30
30 C. Preparing the Icemaker for Long Storage CAUTION When storing the icemaker for an extended time or in sub-freezing temperatures, follow the instructions below to prevent damage. When the icemaker is not used for two or three days under normal conditions, it is sufcient to move the control switch to the "OFF" position. When storing ...
-
Perlick H50IMS-ADR - page 31
31 Full One Year Warranty: one year ? ...
Hai una domanda su Perlick H50IMS-ADR?
Utilizza il modulo sottostante
Se non hai risolto il problema con Perlick H50IMS-ADR con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Perlick H50IMS-ADR è probabile che voglia condividere il modo di risolverlo.