Manuale per l’uso Casio KL-8200

36 pagine 1.84 mb
Scarica

Vai alla pagina of 36

Summary
  • Casio KL-8200 - page 1

    KL-8200 User ’ s Guide ...

  • Casio KL-8200 - page 2

    E-1 Important Safety Precautions Note of the following safety precautions before using the label printer for the first time. Keep these safety precautions and operating instructions on hand for future reference. About safety precaution symbols The following symbols are used in this manual and on the product itself to alert you and others to the ris ...

  • Casio KL-8200 - page 3

    E-2 • Avoid leaving the unit on a kitchen table, next to a humidifier , or in any other area where it might come into contact with oil vapors or steam. Such conditions create the danger of fire and electri- cal shock. • Never place heavy objects on the unit. Doing so creates the danger of the unit falling, result- ing in personal injury . Lithi ...

  • Casio KL-8200 - page 4

    E-3 Contents Important Safety Precautions ...................... E-1 Quick Reference ............................................ E-2 Part 1 Getting Acquainted ........................... E-4 Important Precautions .............................................. E-4 General Guide .......................................................... E-5 Label Pr ...

  • Casio KL-8200 - page 5

    E-4 T o store a bar code ............................................ E-23 T o recall a bar code from memory ..................... E-23 T o delete a bar code from memory .................... E-23 NUMBERING .......................................................... E-23 T o print sequentially numbered labels ................ E-23 T o store a numberi ...

  • Casio KL-8200 - page 6

    E-5 Bottom General Guide Front Replacing the Cover if it Comes Off If the cover comes off, replace it as shown in the illustra- tion nearby . T ake care to avoid damaging the tabs and hinges when installing the cover . Power Keys Turn power on and off. Handle AC adaptor connector 3-pin jack T ape cartridge compartment Cover release T ape outlet Pri ...

  • Casio KL-8200 - page 7

    E-6 • Use only an adaptor , and make sure the adaptor has the same voltage rating as the household current in your area. Using a wrong adaptor can damage your label printer . • Be sure to turn the label printer off before you connect the adaptor . Do not turn power on until the adaptor is con- nected to the label printer and plugged into an AC ...

  • Casio KL-8200 - page 8

    E-7 Important! Never try to push the tape back into the cas- sette. Once tape is out of the cassette, there is no way to wind it back in. T rying to do so can cause operational prob- lems with the label printer . T o load a tape cartridge 1. Make sure the label printer is turned off. 2. Press the cover release and open the cover. • If there is a ...

  • Casio KL-8200 - page 9

    E-8 Use u and i to move the highlighting to the item you want to select and then press SET . Press ESC to clear the SET UP menu without selecting anything. The following sections explain how to use most of the SET UP menu items. See page E-12 for details on using DEF AUL T FONT , page E-1 1 for how to use INPUT , and page E-19 for DENSITY . Message ...

  • Casio KL-8200 - page 10

    E-9 Shift indicator This indicator appears when you press the SHIFT key . While this indicator is on the display , the keyboard is shifted, so the letter keys input the opposite of their current upper-case/lower- case setting. The number keys input the punctuation symbols marked in the upper right corners of the keys. The keyboard automatically uns ...

  • Casio KL-8200 - page 11

    E-10 2. Use u and i to move the highlighting to the item you want to select and then press SET . • Pressing SET causes a menu of symbols, dingbats, number formats, or characters to appear . • T o clear the SYMBOL menu without selecting anything, press ESC . 3. Use u , i , t and y to move the highlighting to the character you want to select, and ...

  • Casio KL-8200 - page 12

    E-11 2. Use u and i to move the highlighting to “ RECALL ” and then press SET . 3. Use u , i , t and y to select the user character you want and then press SET . T o delete a user character 1. Press FUNC and then ILLUST (USER CHR). 2. Use u and i to move the highlighting to “ DELETE ” and then press SET . 3. Use u , i , t and y to select th ...

  • Casio KL-8200 - page 13

    E-12 Part 5 Character Attributes and T ext Effects The operations in this part of the manual explain how to change fonts and character styles. These characteristics are called “character attributes”. It also tells you how to assign such text effects as underlining, shading, and box printing to text. Important! • Character attributes you speci ...

  • Casio KL-8200 - page 14

    E-13 T o change the character styles 1. While there is text on the display , press STYLE . – – – – – E L Y T S – – – – L A M R O N D L O B E N I L T U O W O D A H S D E S I A R 2. Use u and i to highlight the style you want to change to and then press SET . – – – – – E L Y T S – – – – – E G N A R – L L A K C ...

  • Casio KL-8200 - page 15

    E-14 T o change the text effect for specific characters 1. After performing the two steps under “ T o assign text ef- fects ” , use u and i to highlight “ CHARACTER ” and then press SET . 2. Move the cursor to the start character from which you want to change the text effect and then press SET to register your selection. 3. Move the cursor ...

  • Casio KL-8200 - page 16

    E-15 About the format menu The format that appears in the following procedure uses symbols to indicate character sizes in each line of text. The formats that appear depend on the width of the tape loaded in the label printer and the number of lines in the block of text where the cursor is located when you press the SIZE key . The following shows al ...

  • Casio KL-8200 - page 17

    E-16 T o cancel superscripting and subscripting 1. While there is superscripted or subscripted text on the display , press SIZE . 2. Use u and i to highlight “ SUPER/SUB ” and then press SET . 3. Use u and i to highlight “ CANCEL ” and then press SET . 4. Select the range of characters for which you want to can- cel superscripting or subscr ...

  • Casio KL-8200 - page 18

    E-17 T o create a block Example: T o input the text “ ABXYZ Computer Company ” and create two blocks: “ ABXYZ ” and “ Computer Company ” . 1. Input the text. 2. Move the cursor to the space between “ ABXYZ ” and “ Computer Company ” . 3. Press BLOCK . B L o C r e t u p m o C Z Y BX A 2 S N A S a m c 0 . 3 1 2 × 2 • If you wan ...

  • Casio KL-8200 - page 19

    E-18 All T ext Operations The procedures in this section control the following param- eters for all of the text on the display . • Mirror printing (mirror , normal) • Proportional character spacing (on, off) • Smoothing (on, off) • Block space (none, narrow , wide) • Feed (long, short, manual) • T ape length (auto, fixed) • Block alig ...

  • Casio KL-8200 - page 20

    E-19 Part 8 Printing This part of the manual includes all the information you need to print tapes. Note The following information covers basic printing pro- cedures only . Other printing related information can be found in the sections of this manual describing presets (page E-20), stamp printing (page E-25), frames, and memory op- erations (page E ...

  • Casio KL-8200 - page 21

    E-20 T o specify frames around each character 1. Input the text you want to frame. 2. Press FRAME . – – – – – E M A R F – – – – 1 E T C A R A H C H C A E – 3. Use u and i to move the highlighting to “ EACH CHAR- ACTER ” and press SET . 4. Use u , i , t and y to move the highlighting to the frame you want to use and press SET ...

  • Casio KL-8200 - page 22

    E-21 2. Use u and i to move the highlighting to “ ST ORE ” and then press SET . m c 8 . 4 1 H T G N E L m m 8 1 H T D I W A ? E M A N 3. Input up to five characters for the name of the label, and then press SET . C S E / T E S ? E R O T S % 0 2 Y R O M E M D E S U – – – – T U O Y A L – – – – 4. Press SET to store the label or ES ...

  • Casio KL-8200 - page 23

    E-22 12. Use u and i to move the highlighting to “ EXIT ” and then press SET . 13. Press SET to end the operation. T o store an original layout 1. Perform steps 1 through 10 under “ T o create a new origi- nal layout ” to create the layout. 2. Use u and i to move the highlighting to “ ST ORE ” and then press SET . 3. Input up to five ch ...

  • Casio KL-8200 - page 24

    E-23 • Always test bar codes produced using this label printer before actually using them. If bar codes cannot be read properly , try adjusting the print density (page E-19) or us- ing a larger character size. EAN-13, EAN-8, UPC-A, UPC-E The following applies to EAN-13, EAN-8, UPC-A, and UPC- E bar codes. T o print a bar code 1. While the PRESETS ...

  • Casio KL-8200 - page 25

    E-24 2. Use u and i to move the highlighting to “ NEW ” and press SET . 4 3 2 1 m c O T U A H T G N E L H T D I W m m 8 1 3. Use t and y to move the highlighting to the number of the format you want and then press SET . S N A S R E B M U N a m c O T U A H T G N E L H T D I W 1 m m 8 1 4. Input the starting number of the numbering sequence and t ...

  • Casio KL-8200 - page 26

    E-25 T o change the week’s starting day 1. While a calendar is on the display , press FORM . – – – – – M R O F – – – – – T A M R O F L L A R A D N E L A C 2. Use u and i to move the highlighting to “ CALENDAR FORMA T ” and then press SET . • Y ou can specify either mirror or normal printing (page E-18) and feed setting ( ...

  • Casio KL-8200 - page 27

    E-26 5. Use u and i to move the highlighting to “ EXIT ” and then press SET . 6. Press SET to end the operation. T o recall a stamp label from memory 1. While the ST AMP menu is on the display , use u and i to move the highlighting to “ RECALL ” and then press SET . 2. Use u and i to display the name of the label you want, and then press SE ...

  • Casio KL-8200 - page 28

    E-27 • The optional F A-900 makes it possible for you to use the label printer to print data created on your personal com- puter . Importing Data from an SF Unit Use the following procedure to send data to the label printer from a SF Unit. T o connect the SF Unit to the label printer 1. Turn off the power of the label printer and the SF Unit. 2. ...

  • Casio KL-8200 - page 29

    E-28 • If you do not want to receive and append any more data items, skip steps 4 and 5. 5. Repeat step 3 to receive more data. • The “ ! ” indicator means that data items will be printed one at a time. If you want to print all of the received data items at once, press B to change “ ! ” to “ A ” . Press B again to change back to “ ...

  • Casio KL-8200 - page 30

    E-29 • Use a tape width of at least 18mm when received data item character size is increased vertically by a factor of two. • None of the following functions can be used with received data: frames, preset formats, auto sizing, preset layouts, block operations, proportional character spacing, smooth- ing, character input settings, character dele ...

  • Casio KL-8200 - page 31

    E-30 ENLARGED Label Measurements Illustrations Symbols, Dingbats, and Special Characters ● SYMBOL ● DINGBA T ● NUMBER ● GREEK, RUSSIAN Frames ● ALL TEXT ● EACH CHARACTER Fonts 24 mm 18 mm 12 mm 2 pieces 3 pieces 4 pieces 2 pieces 3 pieces 4 pieces 4 pieces Large 2 pieces 3 pieces 4 pieces 4 pieces Large 8 × 8 times 12 × 12 times 16 × ...

  • Casio KL-8200 - page 32

    E-31 Bar Code Specifications *1 The check digit is automatically calculated in accordance with input data. For EAN-13, EAN-8, UPC-A, and ITF , the check digit is appended at the end of the printed digits. For CODE39 and CODABAR, the check digit is appended one digit before the final digit (when a check digit is used). *2 UPC-E includes a check digi ...

  • Casio KL-8200 - page 33

    E-32 • • • • • Data Communication Only blank spaces were input. Input the text you want to print. T ape comes out when PRINT is pressed, but nothing is printed on it. Possible Cause Action • • • • • T ape Cutting • • • • • Using Labels Improper print density setting Improper loading of the cartridge Dirty print head or ...

  • Casio KL-8200 - page 34

    E-33 Message Cause and Recommended Action T ext being printed with a frame does not fit within a fixed-length tape. Shorten the text or change the tape length. Print operation attempted when memory is not initialized. Perform the reset operation and try again. Memory data has been deleted or corrupted bacause battery went dead. T ext storage attemp ...

  • Casio KL-8200 - page 35

    E-34 Specifications Model: KL-8200 Input Keyboard Layout: T ypewriter (QWERTY) Character T ypes Alpha (English and other languages): 52 (A~Z, a~z), 99 ( Á , ß , Ç , W etc.) Numbers: 10 Symbols/Greek and Russian Characters: 306 Illustrations: 50 Display T ype: Liquid crystal display Columns: 12 Lines: 4 Printing T ype: Thermal transfer Speed: App ...

  • Casio KL-8200 - page 36

    CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome Shibuya-ku, Tokyo 151-8543, Japan ...

Fabbricante Casio Categoria Printer

I documenti che otteniamo dal fabbricante del dispositivoCasio KL-8200 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Casio
- manuali per l’uso KL-8200
- schede prodotto Casio
- opuscoli
- o etichette energetiche Casio KL-8200
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Casio KL-8200.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Casio KL-8200, manuali di manutenzione, brevi manuali o manuali utente Casio KL-8200. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Casio KL-8200.

Manuali per l’uso simili

Manuale completo del dispositivo Casio KL-8200, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Casio KL-8200 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Casio KL-8200.

Il manuale per l’uso completo Casio, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Casio KL-8200 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Casio KL-8200, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Casio KL-8200 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Casio KL-8200 - che ci dovrebbe aiutare nei primi passi durante l'uso Casio KL-8200
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Casio KL-8200
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Casio KL-8200 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Casio KL-8200?

Utilizza il modulo sottostante

Se non hai risolto il problema con Casio KL-8200 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Casio KL-8200 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)