Italiano dropdown-ico

Manuale per l’uso Makita DCS461

36 pagine 4.02 mb
Scarica

Vai alla pagina of 36

Summary
  • Makita DCS461 - page 1

    Instruction Manual Original Instruction Manual Important: Read this instruction manual carefully before putting the chain saw into operation and strictly observe the safety regulations! Keep this instruction manual! DCS460 DCS461 DCS500 DCS501 ...

  • Makita DCS461 - page 2

    2 RE Y EU Conformity Declaration The undersigned, T amiro Kishima and Rainer Bergfeld, as authorized by DOLMAR GmbH, declare that the MAKIT A machines, T ype: EU prototype test certi Þ cate No. DCS460, 461 (178) M6T 09 10 24243 108 DCS500, 501 (179) M6T 09 10 24243 108 manufactured by DOLMAR GmbH, Jenfelder Str . 38, 22045 Hamburg, Germany , confo ...

  • Makita DCS461 - page 3

    3 1 4 5 6 7 3 2 Delivery inventory DCS461/501 = Saw with decompression valve 1. Chain saw 2. Guide bar 3. Saw chain 4. Chain protection cover 5. Universal wrench 6. Offset screwdriver 7. Screwdriver for carburetor adjustment 8. Instruction manual (not shown) In case one of the parts listed should not be included in the delivery inventory , please c ...

  • Makita DCS461 - page 4

    4 4 5 6 7 1 2 3 1 4 3 2 SAFETY PRECAUTIONS Intended use Power chain saws This power chain saw may be used only for sawing wood out of doors. It is intended for the followisng uses depending on its class: - Professional and mid-class: Use on small, medium and large trees: felling, limb removal, cutting to length, thinning. - Hobbyklasse: Occasional ...

  • Makita DCS461 - page 5

    5 6 5 7 8 9 ● Maintenance ● Stopping work ● Refuelling ● T ransport ● Sharpening the chain ● Putting out of function 3 Meter Fuels / Refuelling - Stop the engine before refuelling the chain saw. - Do not smoke or work near open Þ res (5). - Let the engine cool down before refuelling. - Fuels can contain substances similar to solvents. ...

  • Makita DCS461 - page 6

    6 10 12 13 14 11 Kickback - When working with the chain saw dangerous kickbacks may occur . - Kickback occurs when the upper part of the end of the guide bar inadvertently touches wood or other hard objects (10). - This causes the saw to be thrown back toward the user with great force and out of control. Risk of injury! In order to prevent kickback ...

  • Makita DCS461 - page 7

    7 15 16 17 18 19 2 1 / 2 45° 45° = cutting down area - Be careful when cutting splintery wood. Cut pieces of wood may be pulled along (risk of injuries). - When cutting with the upper edge of the guide bar, the chain saw may be pushed in the direction of the user if the chain gets clamped. For this reason use the lower edge of the bar whenever po ...

  • Makita DCS461 - page 8

    8 20 21 22 24 T ransport and storage - When changing your location during work switch off the chain saw and actuate the chain brake in order to prevent an inad- vertent start of the chain. - Never carry or transport the chain saw with the chain run- ning. - When transporting the chain saw over long distances the guide bar protection cover (delivere ...

  • Makita DCS461 - page 9

    9 2 24 25 16 17 18 19 3 4 1 6 7 5 8 9 11 12 13 14 15 20 21 22 23 10 Stroke volume cm 3 45,6 49,9 Bore mm 43 45 Stroke mm 31,4 31,4 Max. power at speed 3) kW / 1/min 2,2 / 10,000 2,4 / 10,000 Max. torque at speed 3) Nm / 1/min 2,7 / 7,000 2,9 / 7,000 Idling speed / max. engine speed with bar and chain 1/min 2,500 / 13,800 2,500 / 13,800 Clutch engag ...

  • Makita DCS461 - page 10

    10 5 7 6 5 4 1 2 3 C D B A Put on the guide bar ( 7 ). Make sure that the pin ( 5 ) of the chain tensioner engages in the hole in the guide bar . Remove the plastic transport cover (*) and dispose of prop- erly . Turn chain tensioning screw ( 4 ) to the left (counter-clockwise) until the pin ( 5 ) of the chain tensioner is underneath the threaded p ...

  • Makita DCS461 - page 11

    11 8 10 1 9 9 12 2 4 F H E 2 3 G Replace the sprocket guard (3). Tighten the nuts ( 2 ) only hand-tight to begin with. Lift the chain ( 9 ) over the sprocket ( 8 ). CAUTION: Do not insert the chain between the chain sprocket and the disc. Guide the chain from above about halfway into the groove ( 10 ) on the guide bar . Place the chain over the cha ...

  • Makita DCS461 - page 12

    12 2 4 1 2 1 C B A Engaging the chain brake (braking) If the kickback is strong enough the sudden acceleration of the guide bar combined with the inertia of the hand guard ( 1 ) will automatically actuate the chain brake. T o engage the chain brake manually , simply push the hand guard ( 1 ) forward (towards the tip of the saw) with your left hand ...

  • Makita DCS461 - page 13

    13 E + OIL 50:1 OIL D Fuel CAUTION: This saw is powered by mineral-oil products (gasoline and oil) . Be especially careful when handling gasoline . Do not smoke. Keep tool well away from open ß ames, spark, or Þ re (explosion hazard). Fuel mixture This tool is powered by a high-performance air-cooled two-stroke engine. It runs on a mixture of gas ...

  • Makita DCS461 - page 14

    14 A B NEVER USE W ASTE OIL Waste oil is very dangerous for the environment. Waste oil contains high amounts of carcinogenic substances. Residues in waste oil result in a high degree of wear and tear at the oil pump and the sawing device. In case of damage caused by using waste oil or unappropriate chain oil the product guarantee will be null and v ...

  • Makita DCS461 - page 15

    15 2 3 1 C E D Checking the chain lubrication Never work with the chain saw withoute suf Þ cient chain lubri - ca tion. Otherwise the service life of the chain and guide bar will be reduced. Before starting work check the oil level in the tank and the oil feed. Check the oil feed rate as described below: Start the chain saw (see „Starting the en ...

  • Makita DCS461 - page 16

    16 A B 1 4 5 3 2 Cold start (Choke) W arm start (ON) Engine off Combination switch in safety position (ignition current cut off, necessary for all mainte- nance, repair , and installation work) Starting the engine Do not start the chain saw until after it is completely as- sembled and checked! Move at least 3 meters / 10 feet away from the place wh ...

  • Makita DCS461 - page 17

    17 6 C 7 8 Working in winter In order to prevent carburetor icing in conditions of low tempe- rature combined with high humidity , and below + 5°C in order to get up to operating temperature faster , heated air can be taken from the cylinder . Remove the cover (see “Cleaning the air Þ lter”). Remove the insert ( 7 ) and insert it as shown for ...

  • Makita DCS461 - page 18

    18 H S L A CAUTION: Do not adjust the carburetor until the machine has been completely assembled and checked! Do not adjust the carburetor without a tachometer! Carburetor adjustment is necessary for optimum engine performance, for safer and more economical operation. Adjust the carburetor only with the engine warm, a clean air Þ lter, and properl ...

  • Makita DCS461 - page 19

    19 B Adjusting the carburetor (only for not EU-countries) Carburetor adjustment is necessary for optimum engine performance, for safer and more economical operation. The engine should be warm, the air Þ lter clean, and the chain properly tensioned. Have carburetor adjustment done by an authorised MAKIT A service centre. The carburetor is factory-a ...

  • Makita DCS461 - page 20

    20 min. 3 mm (0.11”) A B C The sharpening angle ( α ) must be identical for all cutters! 25° for chain type 686, 099 30° for chain type 086, 484 35° for chain type 093 The teeth will have the proper angle (ß) automatically if the proper round Þ le is used. 60° for chain type 686, 099 85° for chain type 086, 093, 484 Different angles resul ...

  • Makita DCS461 - page 21

    21 1 2 D 4/5 E F Chain typ 086, 484, 686, 099 Chain typ 093 Files and how to work with them Use a special saw chain round Þ le for sharpening. Standard round Þ les are unsuitable. For the order number , see “Accessories”. T ype 086, 484, 686 : File the Þ rst cutter half with a 4,8 mm dia. round saw-chain Þ le, then switch to a 4.5 mm dia. ? ...

  • Makita DCS461 - page 22

    22 7 2 3 1 4 6 5 A B Cleaning the brake band and sprocket interior CAUTION: Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see „Replacing the spark plug“) . Always wear protective gloves! CAUTION: Start the chain saw only after having assembled it completely and inspected. ...

  • Makita DCS461 - page 23

    23 8 12 13 11 9 14 15 C Check the sprocket before mounting a new chain. Worn out sprockets ( 8 ) may damage the new chain and must therefore be replaced. Remove the sprocket guard (See „PUTTING INTO OPERA TI- ON“ Þ gs. B ). Remove the chain and guide bar . Remove circlip ( 9 ). CAUTION: The circlip will pop out of the groove. When removing it, ...

  • Makita DCS461 - page 24

    24 5 3 6 4 A 1 2 5 3 4 5a CAUTION: T o prevent eye injury , always wear eye protection when cleaning the Þ lter with compressed air! Do not use fuel to clean the air Þ lter . Disengage the cover clasp ( 1 ) with the universal wrench and take off the cover ( 2 ). Push up the combination switch ( 3 ) (Choke position) to prevent dirt particles from ...

  • Makita DCS461 - page 25

    25 8 9 7 0,5 mm 11 10 12 B C D Checking the muf ß er screws Remove the retaining plate ( 10 ) by unscrewing screws ( 11 , short) and ( 12 , long). The muf ß er screws are now accessible through the blind holes and can be checked for tight Þ t. If they are loose, hand-tighten them (Important - do not overtighten!). Replacing the spark plug CAUTIO ...

  • Makita DCS461 - page 26

    26 A 1 2 7 8 6 5 14 13 4 4 4 9 10 12 11 3 Replacing the starter cable/ Replacing the return spring pack/Replacing the starter spring Unscrew four screws ( 1 ). Remove fan housing ( 2 ). Remove the air guide ( 3 ) from the fan housing. CAREFUL! Injury hazard! Do not unscrew screw (7) if the return spring is under tension. If the starter cable is to ...

  • Makita DCS461 - page 27

    27 14 B 15 C Replacing the suction head The felt Þ lter ( 15 ) of the suction head can become clogged. It is recommended to replace the suction head once every three months in order to ensure unimpeded fuel ß ow to the carburetor . T o remove the suction head for replacement, pull it out through the tank Þ ller neck using a piece of wire bent at ...

  • Makita DCS461 - page 28

    28 General Chain saw Clean exterior , check for damage. In case of damage, have repaired by a quali Þ ed service centre immediately Saw chain Sharpen regulary , replace in good time 20-12 Chain brake Have inspected regularly at an authorized service centre Guide bar Turn over to ensure even wear of bearing surfaces Replace in good time 12, 22 Star ...

  • Makita DCS461 - page 29

    29 Service, spare parts and guarantee Maintenance and repair The maintenance and repair of modern engines as well as all safety devices require quali Þ ed technical training and a special work- shop equipped with special tools and testing devices. Any work not described in this Manual may be performed only by a MAKIT A service centre. The MAKIT A ...

  • Makita DCS461 - page 30

    30 T rouble shooting Malfunction System Observation Cause Chain does not run Chain brake Engine runs Chain brake actuated. Engine does not start or Ignition system Ignition spark Malfunction in fuel supply system, com- only with dif Þ culty pression system, mechanical malfunction. No ignition spark Switch on ST OP , fault or short-circuit in the w ...

  • Makita DCS461 - page 31

    31 26 33 27 28 29 30 31/32 25 21 20 5 1 2 3 14 16 12 13 4 15 17 10 11 9 18 19 8 7 6 Extract from the spare parts list Use only original MAKIT A parts. For repairs and replacement of other parts, see your MAKIT A service centre. DCS460 / DCS461 DCS500 / DCS501 ...

  • Makita DCS461 - page 32

    32 Extract from the spare parts list Use only original MAKIT A parts. For repairs and replacement of other parts, see your MAKIT A service centre. DCS460 / DCS461 DCS500 / DCS501 Pos. MAKIT A-No. Qty . Denomination 1 445 033 631 1 Sprocket nose bar .325“, 33 cm (13“) 445 038 631 1 Sprocket nose bar .325“, 38 cm (15“) 445 045 631 1 Sprocket ...

  • Makita DCS461 - page 33

    33 Notes ...

  • Makita DCS461 - page 34

    34 Notes ...

  • Makita DCS461 - page 35

    35 Notes ...

  • Makita DCS461 - page 36

    To Þ nd your local distributor , please visit www .makita-outdoor.com Form: 995 705 302 (3.10 GB) Speci Þ cations subject to change without notice MAKIT A Werkzeug GmbH Postfach 70 04 20 D-22004 Hamburg Germany ...

Fabbricante Makita Categoria Life Jacket

I documenti che otteniamo dal fabbricante del dispositivoMakita DCS461 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Makita
- manuali per l’uso DCS461
- schede prodotto Makita
- opuscoli
- o etichette energetiche Makita DCS461
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Makita DCS461.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Makita DCS461, manuali di manutenzione, brevi manuali o manuali utente Makita DCS461. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Makita DCS461.

Manuali per l’uso simili

Manuale completo del dispositivo Makita DCS461, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Makita DCS461 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Makita DCS461.

Il manuale per l’uso completo Makita, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Makita DCS461 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Makita DCS461, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Makita DCS461 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Makita DCS461 - che ci dovrebbe aiutare nei primi passi durante l'uso Makita DCS461
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Makita DCS461
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Makita DCS461 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Makita DCS461?

Utilizza il modulo sottostante

Se non hai risolto il problema con Makita DCS461 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Makita DCS461 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)