-
Graco 218413 - page 1
Instructions GRACO INC.ąP .O. BOX 1441ąMINNEAPOLIS, MNą55440-1441 Copyright 1980, Graco Inc. is registered to I.S. EN ISO 9001 PLURAL COMPONENT Mixer Manifold 3000 psi (21.0 MPa, 210 bar) Maximum Working Pressure Model 215625 Series C Low V olume Mixer: 1/4 npt fluid outlet; for use in low volume applications, such as air spray urethanes. Model ...
-
Graco 218413 - page 2
2 307400 T able of Contents W arnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operation 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T roubleshooting 8 . . . . . . . . . . . . . . . . . . . . ...
-
Graco 218413 - page 3
3 307400 W ARNING INJECTION HAZARD Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely serious injury , including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury . D Fluid injected into the skin is a serious injury . The injury may look like just a cut ...
-
Graco 218413 - page 4
4 307400 W ARNING FIRE AND EXPLOSION HAZARD Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and re- sult in a fire or explosion and serious injury . D Ground the equipment and the object being sprayed. Follow the grounding instructions on page 5. D If there is any static sparking or you feel an electric s ...
-
Graco 218413 - page 5
5 307400 Installation Grounding Proper grounding is an essential part of maintaining a safe system. T o reduce the risk of static sparking, ground the pump. Check your local electrical code for detailed grounding instructions for your area and type of equipment. Be sure to ground all of this equipment: 1. Pump: use a ground wire and clamp as instru ...
-
Graco 218413 - page 6
6 307400 Operation Start-up The mixer manifold was tested in oil, which was left in to protect the manifold. Before operating, thoroughly flush the manifold to prevent contamination of the fluids. Flushing Procedure CAUTION Be sure to label all fluid path parts “component A” or “component B” when disassembling them. Doing so prevents interc ...
-
Graco 218413 - page 7
7 307400 Operation Be sure all fluid is thoroughly flushed from the hose after each use. Disassemble all other dispensing equipment, as nec- essary , and clean thoroughly . CAUTION T o prevent fluid from setting up in the dispensing equipment, flush the system frequently . Be sure there is adequate solvent in the solvent supply before starting to s ...
-
Graco 218413 - page 8
8 307400 Operation Pressure Relief Procedure W ARNING INJECTION HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying accidentally . Fluid under high pressure can be injected through the skin and cause serious injury . T o reduce the risk of an injury from injection, splashing fluid, or moving parts, f ...
-
Graco 218413 - page 9
9 307400 Service Manifold Repair (See Page 10. ) W ARNING T o reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 8. Note: Repair kits are available for the manifold. Parts included in the kits are indicated with a †, for example (9†) See page 1 1. 1. Relieve the ...
-
Graco 218413 - page 10
10 307400 Parts 11 Ref No.13 Ball V alve 215622, Series B Low V olume Ref No.24 Ball V alve 215623, Series B High V olume 18* 22 15* 27 29 31 30 28 34‡ 33‡ 32‡ 33‡ 23 26 T orque twice to 60–70 in-lb. (6.7–7.9 N S m) 05769 05768 14 20 *17 21 *17 *16 19* 22 15* 19* 25 28 26 30 4† 3† 12 2 1 8 9† 6† 7 6† 9† 8 5 13 or 24 13 or 24 ...
-
Graco 218413 - page 11
11 307400 Parts Models 215625 and 215626, Series C Ref No. Part No. Description Qty . 1 100721 PLUG, internal hex; 1/4; 1/4 npt 2 2 104472 CAPSCREW, hex hd; 10–32 x 1–1/2 12 3† 105694 SEAL, shaft; SST and PTFE R 2 4† 177019 RING, back-up; Delrin R 2 5 177021 NIPPLE, pipe, hex; 1/4 npt 1 6† 177022 SEA T , valve; Delrin R 2 7 HOUSING, manif ...
-
Graco 218413 - page 12
12 307400 Parts Model 241692 Series A 5765B 2 3 4 5 6 9 7 8 Ref No. Part No. Description Qty . 1 215626 MANIFOLD, mixer; see full parts and listing on pages 10 and 1 1 1 2 157676 UNION, swivel, 90 _ 1 3 155699 ELBOW, street 2 4 161037 FITTING, union, adapter 2 Ref No. Part No. Description Qty . 5 156823 UNION, swivel 2 6 108233 V AL VE, needle 2 7 ...
-
Graco 218413 - page 13
13 307400 T echnical Data Maximum working pressure 3000 psi (21.0 MPa, 210 bar) . . . . . . . . . . . . . . . . . . . . . Fluid port size Model 215625 1/4 npt(m) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model 241692 1/2 npt(f) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Graco 218413 - page 14
14 307400 Dimensions Model 215625 Model 215626 Model 241692 A Overall Length 5.0 in (127 mm) 5.5 in (140 mm) 5.5 in (140 mm) B Overall Height 5.375 in. (136 mm) 6.25 in (159 mm) 19.85 in (504 mm) C Overall Width 1.375 in (35 mm) 1.25 in (32 mm) 1.25 in (32 mm) D Fluid Inlets 1/4 npt(m) 3/8 npt(m) 3/8 npt(m) E Solvent Inlet 1/4 npt(m) 1/4 npt(m) 1/4 ...
-
Graco 218413 - page 15
15 307400 Notes head.notes ...
-
Graco 218413 - page 16
16 307400 Graco Standard W arranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by a n authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for ...
Hai una domanda su Graco 218413?
Utilizza il modulo sottostante
Se non hai risolto il problema con Graco 218413 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Graco 218413 è probabile che voglia condividere il modo di risolverlo.