-
Makita 9566CV - page 1
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Angle Grinder 150 mm (6”) MODEL 9566CV DOUBLE INSULA TION ...
-
Makita 9566CV - page 2
2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s ...
-
Makita 9566CV - page 3
3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t ...
-
Makita 9566CV - page 4
4 USE PROPER EXTENSION CORD: Mak e sure your e xtension cord is in good condition. When using an e xtension cord, be sure to use one heavy enough to carr y the current y our product will draw . An undersized cord will cause a drop in line v oltage resulting in loss of power and o verheating. T able 1 shows the correct siz e to use depending on cord ...
-
Makita 9566CV - page 5
5 12. Make sure cord is c lear of wheel. Do not wrap cord ar ound your arm or wrist. If control of tool is lost, cor d may become wrapped around y ou and cause personal injury . 13. Make sure the wheel is not contacting the workpiece bef ore the switch is turned on. 14. Before using the tool on an actual w ork- piece, let it run for a while. Watc h ...
-
Makita 9566CV - page 6
6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Shaft lock CA UTION: • Ne ver actuate the shaft lock when the spindle is mo ving. The tool ma y be damaged. Press the shaft lock to pre vent spindle rotation when install- ing or removing accessori ...
-
Makita 9566CV - page 7
7 Speed adjusting dial The rotating speed can be changed by turning the speed adjusting dial to a given n umber setting from 1 to 5. Higher speed is obtained when the dial is turned in the direc- tion of number 5. And low er speed is obtained when it is turned in the direction of number 1. Ref er to the table f or the relationship between the numbe ...
-
Makita 9566CV - page 8
8 Installing or removing wheel guar d CA UTION: • When using a depressed center grinding wheel/Multi- disc, fle x wheel, wire wheel brush or cut-off wheel, the wheel guard must be fitted on the tool so that the closed side of the guard alwa ys points towa rd the operator . Loosen the le ver on the wheel guard. Mount the wheel guard with the protr ...
-
Makita 9566CV - page 9
9 Installing or removing abrasive disc (optional accessory) NO TE: • Use sander accessories specified in this manual. These must be purchased separately . Mount the rubber pad onto the spindle. Fit the disc on the rubber pad and screw the loc k nut onto the spindle. T o tighten the lock n ut, press the shaft lock fir mly so that the spindle canno ...
-
Makita 9566CV - page 10
10 CA UTION: • After operation, alwa ys s witch off the tool and wait until the wheel has come to a complete stop befo re putting the tool down. Grinding and sanding operation AL W A YS hold the tool fir mly with one hand on housing and the other on the side handle. T ur n the tool on and then apply the wheel or disc to the workpiece. In general, ...
-
Makita 9566CV - page 11
11 • AL W A YS use guard with wire wheel br ushes, assuring diameter of wheel fits inside guard. Wheel can shatter during use and guard helps to reduce chances of personal injur y . Unplug tool and place it upside down allowing easy access to spindle. Remo ve any accessories on spindle. Thread wire wheel brush onto spindle and tighten with the wr ...
-
Makita 9566CV - page 12
12 002986 2 3 5 2 9 10 4 6 7 8 1 11 13 14 12 9566CV 1 Grip 36 2 Wheel guard 3 Inner flange 82 4 Depressed center grinding wheel / Multi-disc 5 Lock nut 5/8-40 6 Rubber pad 125 7 Abrasiv e disc 8 Sanding lock nut 5/8-48 9 W ire wheel brush 10 Wire cup brush 11 Wheel guard (For cut-off wheel) 12 Inner flange 48 13 Cut-off wheel 14 Lock nut 5/8-48 - L ...
-
Makita 9566CV - page 13
13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut ...
-
Makita 9566CV - page 14
14 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade ...
-
Makita 9566CV - page 15
15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ALABAMA 2365 Pelham P arkway Pelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadw ay Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211 (501) 224-5733 CALIFORNIA 41850 Chris ...
-
Makita 9566CV - page 16
W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o ...
Hai una domanda su Makita 9566CV?
Utilizza il modulo sottostante
Se non hai risolto il problema con Makita 9566CV con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Makita 9566CV è probabile che voglia condividere il modo di risolverlo.