Italiano dropdown-ico

Manuale per l’uso Jonsered GR2032L

28 pagine 1.09 mb
Scarica

Vai alla pagina of 28

Summary
  • Jonsered GR2032L - page 1

    Read through the Operator's Manual carefully and understand the content before using the machine. Operator´s manual (EP A) ...

  • Jonsered GR2032L - page 2

    2 – English Symbols SYMBOL EXPLANA TION W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can r esult in serious or fatal injury to the operator or others. Read through the O perator‘ s Manual carefully and understand the content before using the machine. Always use • A protective helmet where ther ...

  • Jonsered GR2032L - page 3

    English – 3 CONTENTS List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS P ersonal pr otective equipment ............................................. 4 The ...

  • Jonsered GR2032L - page 4

    4 – English The machine ‘ s saf ety equipment This section describes the machine ‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (See the chapter “What is what“ to locate where this equipment is positioned on your machine.) P ersonal pr otective equipment SAFETY INS ...

  • Jonsered GR2032L - page 5

    English – 5 SAFETY INSTR UCTIONS 4. Vibration damping system Y our machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible. U se of incorrectly wound cord or incorr ect cutting equipment increases the level of vibration. The machine ’ s vibration damping system reduces the ...

  • Jonsered GR2032L - page 6

    6 – English 3. Cutting attachment guard • Ensure that the spray guard is undamaged and is not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" . SAFETY INSTR UCTIONS Contr ol, maintenance and service of the machine ‘ ...

  • Jonsered GR2032L - page 7

    English – 7 SAFETY INSTR UCTIONS 6. Cutting equipment The section describes how through corr ect maintenance and through using the right type of cutting equipment you can: • Obtain maximum clearing capacity. • Increase the service life of the cutting equipment. T wo basic rules: 1) Only use the cutting and guard equipment we recommend! See ch ...

  • Jonsered GR2032L - page 8

    8 – English SAFETY INSTR UCTIONS General safety instructions Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like. • When storing and tra ...

  • Jonsered GR2032L - page 9

    English – 9 ! General w orking instructions SAFETY INSTR UCTIONS Basic working techniques • Always drop to idling speed after each working operation. Longer periods running at full throttle without loading the engine (that is without resistance, which the engine feels from the cutting equipment when trimming) can lead to serious engine damage. ...

  • Jonsered GR2032L - page 10

    10 – English SAFETY INSTR UCTIONS Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. NOTE! This technique increases the wear on the cord. • The cord wears quicker and must be fed forward ...

  • Jonsered GR2032L - page 11

    English – 11 WHA T IS WHA T? 26 CL ¥ JONSERED SERVICE ¢ = 25 27 15. Air purge 16. Air filter cov er 17. Clutch cov er 18. Handlebar adjustment 19. Locking nut 20. S upport flange 21. Drive disc 22 Shaft coupling 23. Socket spanner 24. Operator ‘ s Manual 25. Harness 26. Allen key 27. Locking pin What is what on the trimmer? 1. T rimmer head 2 ...

  • Jonsered GR2032L - page 12

    12 – English ASSEMBL Y Assembling the loop handlebar Assembly of the trimmer head I t is extremely important that the disc drive ’ s/support flange ’ s guide engages correctly in the cutting equipment ’ s centre hole when assembling the cutting equipment. C utting equipment assembled incorrectly can r esult in serious and/or fatal personal ...

  • Jonsered GR2032L - page 13

    English – 13 ASSEMBL Y Assembling other guards and cutting equipment B A L M C H Assembling and dismantling the two-part shaft (GR2026CL) • Fit the guard (A) intended for use with the trimmer head. Secure using four bolts (L) and the support plate (M) as shown in the diagram. • Fit the disc drive (B) on the output axle. • Turn the blade axl ...

  • Jonsered GR2032L - page 14

    14 – English FUEL HANDLING Fuel mixture W ARNING! Always pr ovide good ventilation when handling fuel. ! Fuelling ! ! W ARNING! The catalytic con verter muffler gets very hot during and after use. This also applies during idling. Be aware of the fire hazar d, especially when handling the saw near flammable substances or vapour s. Gasoline NO TE! ...

  • Jonsered GR2032L - page 15

    English – 15 ST ART AND ST OP Contr ol before starting Cold engine IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke position. AIR PUR GE: P ress the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. Warm engine U se the same starting p ...

  • Jonsered GR2032L - page 16

    16 – English Carburetor Y our JONSERED product has been designed and manufactured to specifications that r educe harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. T o ensur e that your unit is at peak performance and producing the least amount of harmful emissions after br eak in, have your authorized se ...

  • Jonsered GR2032L - page 17

    English – 17 Final setting of the idling speed T Adjust the idling speed with the screw T , If it is necessary to readjust. F irst turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ move. Then turn, counter- clockwise until the cutting attachment stops. A correctly adjusted idle speed setting occurs whe ...

  • Jonsered GR2032L - page 18

    18 – English MAINTENANCE Muffler NO TE! Some mufflers ar e fitted with a catalytic converter . See “ T echnical data ” to see whether you clearing saw is fitted with a catalytic converter . The muffler is designed to dampen the noise level and to direct the exhaust fumes away from the user . The exhaust fumes are hot and can contain sparks, w ...

  • Jonsered GR2032L - page 19

    English – 19 MAINTENANCE If the machine is low on po wer , difficult to star t or runs poorly while idling always check the spark plug first. If the spark plug is dirty , clean it and at the same time check that the electrode gap is 0.5 mm. The spark plug should be changed after about one month of operation or earlier if necessary . NO TE! Always ...

  • Jonsered GR2032L - page 20

    20 – English TECHNICAL D A T A T echnical data Engine Displacement, cu. in/cm 3 Cylinder bor e, inch/mm S troke length, inch/mm I dling speed, rpm Recommended max. speed, rpm S peed of output shaft, rpm Max. engine output, acc. to ISO 8893 Catalytic converter muffler S peed-regulated ignition system Ignition system Manufactur er/type of ignition ...

  • Jonsered GR2032L - page 21

    English – 21 Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EPA (U.S. Environmental Protection Agency), Environment Canada and Jonsered are pleased to explain the emissions control system warranty on your 2001 and later small off-road engine. In U.S. and Canada, new small off-road engines must be designed, built and equipped to meet the federal stri ...

  • Jonsered GR2032L - page 22

    22 – English 1 Auto 32 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " 15 cm 15 cm ...

  • Jonsered GR2032L - page 23

    English – 23 1 Poly T rim 2 3 4 5 6 7 8 >20mm >20mm ! B A 6 Nm X 10 ...

  • Jonsered GR2032L - page 24

    24 – English 1 T ap-N-Go Pro 2 5 6 7 8 9 10 12 “Click” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6" ...

  • Jonsered GR2032L - page 25

    English – 25 1 T rimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6" ...

  • Jonsered GR2032L - page 26

    26 – English 1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11 ' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" T rimmy SII ´*xt3¶5)¨ ...

  • Jonsered GR2032L - page 27

    English – 27 ~ 15 cm 6' N ~ 15 cm 6' 502 25 56-01 502 26 04-01 502 25 53-01 502 26 24-01 (x2) 740 43 14-00 502 25 52-01 502 26 01-01 735 31 19-00 729 53 27-71 (x3) 738 21 03-04 502 26 03-01 502 27 07-01 502 26 86-01 1 23 4 T rimmy SII ...

  • Jonsered GR2032L - page 28

    108 88 41-95 ´*xt3¶5)¨ 2002W04 ...

Fabbricante Jonsered Categoria Brush Cutter

I documenti che otteniamo dal fabbricante del dispositivoJonsered GR2032L possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Jonsered
- manuali per l’uso GR2032L
- schede prodotto Jonsered
- opuscoli
- o etichette energetiche Jonsered GR2032L
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Jonsered GR2032L.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Jonsered GR2032L, manuali di manutenzione, brevi manuali o manuali utente Jonsered GR2032L. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Jonsered GR2032L.

Manuali per l’uso simili

Manuale completo del dispositivo Jonsered GR2032L, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Jonsered GR2032L dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Jonsered GR2032L.

Il manuale per l’uso completo Jonsered, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Jonsered GR2032L - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Jonsered GR2032L, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Jonsered GR2032L che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Jonsered GR2032L - che ci dovrebbe aiutare nei primi passi durante l'uso Jonsered GR2032L
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Jonsered GR2032L
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Jonsered GR2032L in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Jonsered GR2032L?

Utilizza il modulo sottostante

Se non hai risolto il problema con Jonsered GR2032L con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Jonsered GR2032L è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)