Italiano dropdown-ico

Manuale per l’uso Ricoh MP5125A

39 pagine 1.54 mb
Scarica

Vai alla pagina of 39

Summary
  • Ricoh MP5125A - page 1

    NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not install ...

  • Ricoh MP5125A - page 2

    CAUTION Rating voltage for peripherals. 1. Headphone Jack Rating Voltage output Audio Signal Max. 2V FCC WARNING Changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the followi ...

  • Ricoh MP5125A - page 3

    The company names and product names written in this manual are trademarks or registered trademarks. ● *1 For information on Windows® XP supports, visit Ricoh's Web site. ...

  • Ricoh MP5125A - page 4

    This manual uses the following symbols to indicate important information relating to the drive. Failing to comply with the information in this manual and/or incorrect handling of the drive may result in serious personal injury or damage to the product. Indicates restriction or precaution that should be observed. Provides useful additional informati ...

  • Ricoh MP5125A - page 5

    This user's manual (hereafter referred to as "the manual") contains important notes and product handling information. Be sure to read the manual before using the product. For easy reference in the future, please keep the manual at a handy location. Multimedia Printer series Thank you for purchasing the Multimedia Printer series drive ...

  • Ricoh MP5125A - page 6

    Obey the following cautions when handling the drive or discs. Cautions During Installation Install the drive in accordance with the specifications. Be careful to avoid locations likely to cause vibration or shock. ● Avoid locations where there is high humidity, excessive dust, or poor ventilation. ● Avoid locations in direct sunlight, with seve ...

  • Ricoh MP5125A - page 7

    In wintertime, don't use a disc soon after bringing in from outdoors. Use it only after it has reached room temperature. ● Cautions Concerning Disc Cleaning Remove the media by pressing the eject button. ● Use compressed air to clear dust from the media. (Spray the compressed air for about 5 seconds). ● Check to see if there is dirt on t ...

  • Ricoh MP5125A - page 8

    fig1 Check 1. Recording surface 2. fig2 50 to 100mm 1. Back ...

  • Ricoh MP5125A - page 9

    The drive is a super-combination drive that integrates DVD+RW/+R and CD-RW capabilities. Capitalizing on Ricoh's expertise accumulated with existing CD-RW and DVD-ROM combination drives, we have developed some new mechanisms to achieve incorporation of DVD+RW rewrite capabilities. ● DVD writing has been made possible by tuning up a two-LD (l ...

  • Ricoh MP5125A - page 10

    Explains the system environment required for using the drive as a CD-R/CD-RW drive. PC IBM PC/AT compatible Operating System Windows Me/98/95(ORS2 or later) Windows NT Workstation Ver.4.0 (Service Pack 5) or later Windows 2000 (Professional) Windows XP *4 CPU When writing to CD-R/RW: Pentium 166 MHz or higher processors (when JustLink is used). ● ...

  • Ricoh MP5125A - page 11

    Front Panel Rear panel Front Panel Disc tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the disc will be mounted. Caution Don't use force to pull out or push in the disc tray. This might cause damage to the loading section of the drive. 1. Headphone jack Thi ...

  • Ricoh MP5125A - page 12

    Emergency eject hole This drive has a function that allows the disc to be ejected manually for an emergency case such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. Using it excessively will cause malfunction. 6. Rear panel Digital Audio (SPDIF) Output Connector Provides output to ...

  • Ricoh MP5125A - page 13

    Emergency Eject This drive has a function that allows the CD to be ejected manually, if this becomes necessary in an emergency such as failure of the drive or a power outage. Follow the following procedures in such a case. Caution This feature is a last measure to be used only in an emergency. Using it excessively will cause malfunction. Turn the p ...

  • Ricoh MP5125A - page 14

    Disc ejection Press the eject button 1. Slowly take the disc out of the disc tray 2. Press the eject button or push the disc tray and the tray will be inserted back into the drive. 3. ...

  • Ricoh MP5125A - page 15

    Caution After ejecting the disc, return the disc tray inside the unit quickly. When the disc tray is in the ejected position, dust and other debris will enter, possibly causing read errors, write errors, or drive failure. Back Next Load the media Disc ejection Emergency Eject Using the Drive in a Vertical Position ...

  • Ricoh MP5125A - page 16

    Load the media Press the eject button. 1. Place the media on the disc tray. Be careful not to touch the recording surface of the media. Cautions DVD-R/RW (DVD hyphen R/RW)/DVD-RAM media cannot be used. ❍ When using a 120-mm CD, place the disc in the larger circular depression with its label side facing upside. ❍ When using an 80-mm CD, place th ...

  • Ricoh MP5125A - page 17

    Load the disc by pressing the eject button or by lightly pushing in the disc tray. 3. Next ...

  • Ricoh MP5125A - page 18

    Load the media Disc ejection Emergency Eject Using the Drive in a Vertical Position ...

  • Ricoh MP5125A - page 19

    Using the Drive in a Vertical Position The drive can be installed in a vertical position. Locate the four tabs on the disc tray. Turn each of them inwards untill they click into place. 1. When loading a disc, insert it into the inner side of the tabs. Caution Cannot be used with 80mm CDs. Cannot be used with business card CDs. 2. Back Load the medi ...

  • Ricoh MP5125A - page 20

    Specific knowledge of hardware and software is necessary to install the drive. We cannot guarantee against direct or indirect damage resulting from improper connections. Ask your supplier for details of the installation procedure. Before Installation Before installing the drive, please note the following points. You will need the following: A Phill ...

  • Ricoh MP5125A - page 21

    1. Jumper Set Up Before installation, set the jumper on the jumper connector on the rear panel. Master (MA) Drive set as Master (factory default) 1. Slave (SL) Drive set as Slave 2. Cable Select (CS) Drive mode set by CSEL on the host IDE interface 3. The drive can be connected as the Master or Slave on an E-IDE (ATAPI) interface. ● When several ...

  • Ricoh MP5125A - page 22

    Only one jumper should be installed on the jumper connector. If more than one jumper is installed, the drive may malfunction or be damaged. ● Next 1. Jumper Set Up 2. Removing the Computer Cover 3. Mounting the Drive 4. Connecting the Power Connector 5. PC Connections 6. Sound Card Connection 7. Replacing the Computer Cover 8. Device Drivers ...

  • Ricoh MP5125A - page 23

    2. Removing the Computer Cover Make sure all peripheral devices of the computer and the computer itself are turned off, and then remove the cover. Refer to the manual for the computer for details about removing the cover. Caution There may be sharp edges inside the computer take care to avoid injury. (Example: When newly installing the MP5125A driv ...

  • Ricoh MP5125A - page 24

    3. Mounting the Drive Remove the 5 inch drive bay panel from the computer. Refer to the manual for the computer for details. 1. Insert the drive unit into the bay. Do not apply excessive pressure to the cables inside the computer. 2. Secure the drive with the screws provided. If there is not enough space behind the drive, connect the E-IDE cables e ...

  • Ricoh MP5125A - page 25

    Back Next 1. Jumper Set Up 2. Removing the Computer Cover 3. Mounting the Drive 4. Connecting the Power Connector 5. PC Connections 6. Sound Card Connection 7. Replacing the Computer Cover 8. Device Drivers ...

  • Ricoh MP5125A - page 26

    4. Connecting the Power Connector Connect the power cable from the computer's power supply to the socket on the drive unit, fitting the connector properly into the socket. Back Next 1. Jumper Set Up 2. Removing the Computer Cover 3. Mounting the Drive 4. Connecting the Power Connector 5. PC Connections 6. Sound Card Connection 7. Replacing the ...

  • Ricoh MP5125A - page 27

    5. PC Connections The drive connects to the motherboard of the host computer using an IDE interface cable. Both Primary and Secondary connectors are usually provided on the motherboard, which may be connected as follows: Master 1. Slave 2. Motherboard 3. Primary connector 4. Secondary connector 5. less than 6 inches 6. less than 18 inches 7. To Ins ...

  • Ricoh MP5125A - page 28

    ...

  • Ricoh MP5125A - page 29

    To Install as a Slave Drive When connecting the drive as a slave drive, change the position of the slave setting jumper pin on the rear of the system unit. Master drive (Booting hard disk) 1. Slave drive (MP5125A) 2. Secondary connector 3. Primary connector 4. Master drive (Other IDE drive) 5. ...

  • Ricoh MP5125A - page 30

    Back Next 1. Jumper Set Up 2. Removing the Computer Cover 3. Mounting the Drive 4. Connecting the Power Connector 5. PC Connections 6. Sound Card Connection 7. Replacing the Computer Cover 8. Device Drivers ...

  • Ricoh MP5125A - page 31

    6. Sound Card Connection If the computer has a sound card, the drive can be connected to the sound card with an audio cable. Make sure the connections are oriented so that L corresponds to L and R to R. Refer to the manual for the sound card for detailed information regarding connection. Audio digital output The drive supports S/PDIF(IEC958) for di ...

  • Ricoh MP5125A - page 32

    1. Jumper Set Up 2. Removing the Computer Cover 3. Mounting the Drive 4. Connecting the Power Connector 5. PC Connections 6. Sound Card Connection 7. Replacing the Computer Cover 8. Device Drivers ...

  • Ricoh MP5125A - page 33

    7. Replacing the Computer Cover When the installation of the drive unit is complete, replace the computer cover. Back Next 1. Jumper Set Up 2. Removing the Computer Cover 3. Mounting the Drive 4. Connecting the Power Connector 5. PC Connections 6. Sound Card Connection 7. Replacing the Computer Cover 8. Device Drivers ...

  • Ricoh MP5125A - page 34

    8. Device Drivers When using Windows 98/95, Window NT Workstation Ver. 4.0, Windows 2000 (Professional) Windows XP the installation of any special device drivers are not required. In order to ensure normal drive operation or if the drive is not recognized by your computer, please check the following: In order to ensure normal drive operation If the ...

  • Ricoh MP5125A - page 35

    After checking the above-mentioned points, contact the manufacturer of your PC or PC mother-board, if applicable, to obtain an appropriate IDE controller driver. Back 1. Jumper Set Up 2. Removing the Computer Cover 3. Mounting the Drive 4. Connecting the Power Connector 5. PC Connections 6. Sound Card Connection 7. Replacing the Computer Cover 8. D ...

  • Ricoh MP5125A - page 36

    Caution When using CD-ROM/DVD-ROM/CD-R/CD-RW/DVD+RW/DVD+R media, do not attach any stickers or labels to the media. Using discs with labels attached not only causes read and write errors, but data on the disc may be lost due to damage to the media itself. Load the media ● Disc ejection ● Emergency Eject ● Using the Drive in a Vertical Positio ...

  • Ricoh MP5125A - page 37

    Drive : MP5125A Type Internal type Interface Enhanced-IDE (ATAPI) Data buffer memory 2MB Data transfer speed 33.3MB/sec. (Max.) (Ultra DMA mode2) CD-RW/High Speed CD-RW Write/Read speed (Ave.) <Read Speed> 4X: 600KB/sec. 8X: 1200KB/sec. 20X: 3000KB/sec. *1 32X: 4.8MB/sec. *1 <Write Speed> CD-R: 4X: 600KB/sec. 8X: 1200KB/sec. 12X: 2.1MB/ ...

  • Ricoh MP5125A - page 38

    Video-CD * * CD-Text * * DVD+R * * DVD+RW * * DVD-ROM * Loading system Tray type (automatic loading/eject) Power DC5V, DC12V Power consumption 16w Weight Less than 1.2 Kg. Dimensions 146 X 196.5 X 41.3mm Reliability Error Rate: 10 -12 bits or less MTBF: 100,000hours or greater MTTR: Within 30 minutes Environmental Conditions When operating When not ...

  • Ricoh MP5125A - page 39

    * All references to the product in this doc ument are to specifications in effect when the product was released. Copyright RICOH Co.Ltd. All rights reserved. ...

Fabbricante Ricoh Categoria DVD Player

I documenti che otteniamo dal fabbricante del dispositivoRicoh MP5125A possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Ricoh
- manuali per l’uso MP5125A
- schede prodotto Ricoh
- opuscoli
- o etichette energetiche Ricoh MP5125A
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Ricoh MP5125A.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Ricoh MP5125A, manuali di manutenzione, brevi manuali o manuali utente Ricoh MP5125A. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Ricoh MP5125A.

Manuali per l’uso simili

Manuale completo del dispositivo Ricoh MP5125A, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Ricoh MP5125A dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Ricoh MP5125A.

Il manuale per l’uso completo Ricoh, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Ricoh MP5125A - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Ricoh MP5125A, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Ricoh MP5125A che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Ricoh MP5125A - che ci dovrebbe aiutare nei primi passi durante l'uso Ricoh MP5125A
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Ricoh MP5125A
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Ricoh MP5125A in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Ricoh MP5125A?

Utilizza il modulo sottostante

Se non hai risolto il problema con Ricoh MP5125A con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Ricoh MP5125A è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)