Manuale per l’uso Century G600

30 pagine 3.3 mb
Scarica

Vai alla pagina of 30

Summary
  • Century G600 - page 1

    v/4 ,s 9rlrt sy G600 Direct vent Gas Fireplace Heater "s" series INSTALLATION AND OPERATING INSTRUCTIONS lM PORTANT Before Beg inning Installation, Read Instructions Carefully ldrt^lor - &^ep, ,nald ta an 6" silt WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DA ...

  • Century G600 - page 2

    CONTENTS Description lmportant lnformation Installation Instructions, Clearances to Combustibles Log Assembly Glass Replacement Glass Cleaning Venting Installation Procedure Venting Instructions Safety Precautions for the Installer Parts List #1 Planning Your Installation Horizontal I nstallation Vertical Termination Cathedral Ceiling Installation ...

  • Century G600 - page 3

    IMPORTANT INFORMATION - Study these instructions carefully and completely before installation. Installation must conform to Local Codes, or, in the absence of Local Codes, with the Current National Fuel Gas Code, ANSI 2223.1 (USA); Canadian installation must fotlow CAN/CGA-BI49-1 or 2 (latest Edition). Maintain clearances for servicing and proper o ...

  • Century G600 - page 4

    I N STALI-^ATION I NSTR UCTIONS The appliance; when installed must be electrically connected and grounded in accordance with local codes or, in the absence of local codes, with the current CSA C22-1 Canadian Electrical Code (Canada) or the National Electrical Code ANSI/NFPA TGlatest edition (USA). Keep appliance area clear and free from combustible ...

  • Century G600 - page 5

    'l:t i; CLEARANCES TO COMBUSTIBLES For the purpose of orientation, the left and right sides of this appliance are determined when facing the front of the appliance. Combustion and ventilation air should not be obstructed. TOP LEFT SIDE RIGHT SIDE LEFT SIDE RIGHT SIDE BACK TOP FRONT FLOOR REAR CORNER 6rt 6rt 6" 24" 36" 0" 4& ...

  • Century G600 - page 6

    { *' 3-, I 5 a. : i LOG ASSEMBLY IMPORTANI fne logs MUST be placed exactly as shown. lf there is any evidence of carbon, or blackening on the logs, they may be incorrectly placed. Refer to log assembly diagram for correct method. WARNING: USE ONLY ASSEMBLY SHALL BE THE GI.ASS PANEL. GLASS REPI-ACEMENT MANUFACTURER SUPPLIED REPLACEMENT PARTS GL ...

  • Century G600 - page 7

    GLASS CLEANING WARNING: DO NOT CLEAN GLASS WHEN HOT' 1.Turn off Pilot. 2.Remove four screws in door trim and remove' 3. Remove six screws in center glass panel and remove panel' WARNING: DO NOT USE ABRASIVES ON GLASS SURFACE. .with a soft rag or paPer'towel use regular glass cleaner, spray the glass cleaner on gt6ss surface and ...

  • Century G600 - page 8

    GLASS CLEANING WARNING: DO NOT CLEAN GLASS WHEN HOT' 1.Turn off Pilot. 2.Remove four screws in door trim and remove' 3. Remove six screws in center glass panel and remove panel' WARNING: DO NOT USE ABRASIVES ON GLASS SURFACE. 4.with a soft rag or paPer'towel use regular glass cleaner, spray the glass cleaner on gt6ss surface and ...

  • Century G600 - page 9

    :1: VENTING INSTRUCTIONS THESE INSTRUCTIONS APPLY TO THE SIMPSON DURA.VENT DIRECT VENT SYSTEM USED WITH THE CENTURY HEATING G6OO. IMPORTANT Read all instructions carefully before starting the installation. Failure to follow these instructions may create a fire or other safety hazard, and will void the warranty. Be sure to follow these installation ...

  • Century G600 - page 10

    r SAFETY PREcAUTIoNS FoR THE INSTALLER I .Wear gloves and safety glasses for protection. .Exercise extreme caution when using ladders or on roof tops. .Be aware of electrical wiring locations in walls and ceilings. STARTER KIT xA" - Horizontal Termination Part #971 Kit lnctudes: -90" Black Elbow Wall Thimbte -Horizontal Termination Cap -2 ...

  • Century G600 - page 11

    I er t: ljrr :l: !:: Yt 5i :+ €.,' PLANNING YOUR INSTALLATION VEFTICAL TERMINATION STORM COLLAR FIGURE 1 CATHEDRAL CEILING suPPoFT 8OI ptpF. l.ENqrH PIPE I.ENGTH I t ":$h*G'* ROTJND SUPPORT 8ox/wALl- THIMBLE FIGURE 2 THERE ARE TWO BASTC TYPES OF DIRECT VENT SYSTEM INSTALLATION: 11 ,' Horizontal Termination (Fig. 1) 2l Vertical ...

  • Century G600 - page 12

    FIG. 1 123456 TOTAL HORIZONTAL FEET Oo Face of Erllrior Wrll Ercludlng Elboilr) The maximum number of 90 degree elbows permitted per side wall installation is one (1). The maximum number of 45 degree elbows permitted per side wall installation is one (1). On Vertical installations two (2) 45' elbows are allowed. The Century Heating G600 has be ...

  • Century G600 - page 13

    H ORIZONTAL I NSTALIATI ON MALE LOCKING LUGS $ ru l---l!-4 ITI L^-/) FIG.6 *-ffi F I tJ 0 Step 1. Set lhe appliance in it's desired location. Check to determine if wall studs or roof rafters are in the way when the venting system is attached. lf this is the case, you may want to adjust the location of the appliance. Step 2. Vent pipe and fit ...

  • Century G600 - page 14

    NOTE: 1) 2l 3) Step 4. Position the horizontal vent termination in the centre of the 10'inch square hole, and attach to the exterior wall with the four wood screws provided. Before attaching the Vent Termination to the exterior wall, run a bead of non'hardening mastic ' around it's outside edges, so as to make a seal between it ...

  • Century G600 - page 15

    o c, (, E|C tro = E3 €3 =o Eb e= -9 rE s !.3 s €l F €E t $3 : ;E E fF ; E6 -o € tro o 3E rE SE 9 :E O -r'l '= 6e; ! rE 85 be = '3^ i Eg E 33 G sE $;: E gB 5;E g. iE E ggi Ic=a o;it c c5g: E$rt -crE+|,' -CC|a GOOG o igtiiii$,i iiiggigiiii, itsE$;l=sssEsFs5 igiit*Et liglFgIggF* iglliiiiiigil sE$ia$s$gt$i$$E {{3A,|l,1" ...

  • Century G600 - page 16

    Step 6. SliOe the appliance and vent assembly towards the wall, carefully inserting the vent pipe into the vent cap assembly. lt is important that the vent pipe extend into the vent cap sufficient distance so as to resuft in a minimum pipe overlap of 1-114 inches. Secure the connection between the vent pipe and the vent caP by attaching the two she ...

  • Century G600 - page 17

    from the roof to the hole previously drilled in the ceiling, and mark the spot where the vent will penetrate the roof. Determine if ceiling joists, roof rafters, or olher framing will obstruct the venting system. You may wish to relocate the appliance, or to offset, as shown in Fig. 13, to avoid cutting loadbearing members. , , FlG. 14 NOTE: 1) 2 ...

  • Century G600 - page 18

    Step 7. Stip the flashing over the Pipe Section(s) protruding through the roof. Secure the base of the Flashing to the roof with roofing nails. Insure the roofing material overlaps the top edge of the Flashing as shown in Fig. 14. Verify that you have at least the minimum' clearance to combustibles at the roofline. Step 8. FtG. 15 FlG.,16 DIM? ...

  • Century G600 - page 19

    E_ f cATHEDRALcEtLtNG INSTALLATIoN f Step 1. rollow installation Steps 1 and 2 under Vertical Terminations. Step 2. Using the plumb bob, mark the centre- line of the venting system on the ceiling and drill a small hole through the ceiling ' . and roof at this point. From the roof, locate the drill hole and mark the outline of the Cathedral ...

  • Century G600 - page 20

    GENERAL MAINTENANCE Conduct an inspection of the venting system semiannually. Recommended areas to inspect are as follows: 1. Check areas of the Venting System which are exposed to the etements for corrosion. These will appear as rust spots or streaks, and in extreme cases, holes. These components should immediately be replaced. i 2. Remove the C&q ...

  • Century G600 - page 21

    IFOR YOUR SAFETY, READ BEFORE LIGHTINGT WARNING: explosion may life. lf you do not follow these instructions exactly, a fire or result, causing property damage, personal injury or loss of This appliance has a piezo ignition pilot light. When lighting the pilot, follow these instructions exactly. BEFORE LIGHTING smell all around the appliance area f ...

  • Century G600 - page 22

    LIGHTING INSTRUCTIONS 1) STOP! Read the safety information. 2l Push in the gas control knob slightly position. NOTE: Knob cannot be turned knob is pushed in slightly. Do not force. 3) Wait five (5) minutes to clear out any gas. lf you then smell g?s, STOP! Follow "B" in the safety information. lf you dont smell g?s, go to the next step. 4 ...

  • Century G600 - page 23

    1) 2l TO TURN OFF GAS TO APPLIANCE Push in gas control knob slightly and tum cloclcwise - to 'OFF. Do not force. Turn UOFFU all electrical power. MAI NTENANCE INSTRUCTION 1) Periodical visual 'checks of the pilot and burner flames should be conducted to ensure that the flame is present except when the value At -r,' n r0 lVf control ...

  • Century G600 - page 24

    "nt l AF, tr l E PARTS DIAGRAM 24 ...

  • Century G600 - page 25

    PARTS LIST KEY NO. DESCRIPTION PART NO. G600lrGs G600lts G600PGS G600PS 1 1 2 3 4 5 6 8 9 10 11 12 13 13 14 15 16 17 17 18 19 20 21 21 22 23 24 ..i 26 27 28 29 BURNER (NG) BURNER (LP) GRATE #8 x 112 PAN QUAD TEK LOG SET FRONT GLASS ASSEMBLY SIDE GLASS ASSEMBLY GI-ASS FRAME CLIP SIDE GI.ASS CLIPS BLACK GLASS FRAME DOOR HANDLE MAGNETIC CATCH oRrFtcE ...

  • Century G600 - page 26

    3. 4. 5. fan installation instructions (optiAnal fan kit #S31 1921 1. Remove fan from carton. 2. Using four screws provided attach fan to stove as shown above. Be sure to install rubber gromets as shown above. Speed control switch is to be inserted into pedestal, as shown, and tighten until secure. Snap variable speed control knob into place. Plug ...

  • Century G600 - page 27

    F'G. A fan installation instructions (optionaf fan kit #Sgf 2ggl Remove fan from cafton. 4. 5. 1. 2. 3. WARNING Electrical Grounding Instructions This appliance is equipped with a three-prong (grounding) ptug tor your protectaon against shock hazard and shoutd be ptugged directly into a properly grounded three-prong rec,eptacle. Do nol cu{&apo ...

  • Century G600 - page 28

    TROUBLE SHOOTING - G6OO With proper installation and maintenance, your new Gas Fireplace should provide years of trouble-free service. lf you do experience a problem, refer to the trouble shooting guide shown below. This guide will assist a qualified service person in the diagnosis of problems and the corrective action to be taken. SYMPTOM l. Spark ...

  • Century G600 - page 29

    TROUBLE SHOOTING . G6OO SYMPTOM lll. Frequent pilot outage probtem. POSSIBLE CAUSE Pilot flame may be too low or blowlng (high), causlng the pllot safety to drop out. Bad Thermoplle. No L.P. in tank. Bad thermocouple. Flame lmpingement on logs. 1. CORRECTIVE ACTION Clean and adlust pllot flame lor maximum flame implngement on thermocouple. Replace ...

  • Century G600 - page 30

    WARRANTY INFORIIATION KEEP TH'S WARRANTY MODEL SERIAL DATE PURCHASED Always specify modet and seriat numbers when communicating with the factory. We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We make no other wananty, expressed or implied. TWO YEAR ...

Fabbricante Century Categoria Indoor Fireplace

I documenti che otteniamo dal fabbricante del dispositivoCentury G600 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Century
- manuali per l’uso G600
- schede prodotto Century
- opuscoli
- o etichette energetiche Century G600
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Century G600.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Century G600, manuali di manutenzione, brevi manuali o manuali utente Century G600. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Century G600.

Manuali per l’uso simili

Manuale completo del dispositivo Century G600, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Century G600 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Century G600.

Il manuale per l’uso completo Century, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Century G600 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Century G600, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Century G600 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Century G600 - che ci dovrebbe aiutare nei primi passi durante l'uso Century G600
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Century G600
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Century G600 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Century G600?

Utilizza il modulo sottostante

Se non hai risolto il problema con Century G600 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Century G600 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)