-
Gemini GEM-P800 - page 1
Usin g Y our GEM-P800 Security Sy stem ARMED STATUS GEMINI 1 2 3 4 5 6 7 8 Oi219c page 1 Tuesday, September 16, 1997 08:24 ...
-
Gemini GEM-P800 - page 2
Introduction Congratulations on y our purc hase of an advanc ed GEMINI-P800 Secur ity System. Meticulously developed by a leading manuf actur er of s tate-of- the-art sec urity products, this system will provide you w ith unprecedented peace- of-m ind & inc orpo- rates som e of the m ost sophis ticated f eatures available today. Above all, it h ...
-
Gemini GEM-P800 - page 3
3 Important - T est Your Sy stem Weekly ! 1 Bell / Battery Test Test y our bell or s iren by pressing followed by . This will cause the bell, or siren to s ound for 2 seconds and also initiate a test of the battery . 2 Zone Test W alk throughout the prem ises , opening each protected door or window, and activating each m otion sensor . Check the ke ...
-
Gemini GEM-P800 - page 4
ARMED STAT US GEMINI 1 2 3 4 5 6 7 8 4 Key pad Controls and Indi cator s Status Light will light when all zones are secure and system is ready to be Armed. A C Light will light to indicate that AC Power is present. Trouble Light will light and the Keypad sounder will pulse to indicate that a system tr ou- ble is present. (See System troubles, P ...
-
Gemini GEM-P800 - page 5
A rming Your Sy stem When Leaving 1 Before arm in g y our system, m ak e s ure the g reen Statu s li g ht is ON. T his indic ates that all of your protective zones are secure. If any z ones are open, the cor respondin g Zone num ber will be lit. Secure these zones bef ore proceedin g . If any zones cannot be secured, s ee Bypassin g zones below. 2 ...
-
Gemini GEM-P800 - page 6
Protecting Yourself While at Home 1 Bef ore arm in g y our system, m ak e s ure the g reen Statu s li g ht is ON. T his indic ates that all of your protective zones are secure. If any z ones are open, the cor respondin g zone number will be lit. Secure thos e zones before proc eedin g . 2 Enter your User Code and pres s . The g reen Statu s li ...
-
Gemini GEM-P800 - page 7
Emergency Buttons The three s ets of em er gency buttons, if progr am m ed, are always active whether the system is ar m ed or disarm ed. Discus s these Buttons with y our installer. The em ergency signal will only be activated when the two respective buttons are pres sed at the sam e tim e. Fire A larm: Simu ltaneous ...
-
Gemini GEM-P800 - page 8
Disarming Your Sy stem when Returning 1 Enter your premises throu g h the Entry/Exit door. The k eypad w ill sound a steady tone to remind you to disarm the system before your Entry Delay tim e ex pires. 2 Enter your User Code and press . The red Ar m e d li g ht will g o out, indicatin g that the system has been dis arm ed. Note: If you mak e ...
-
Gemini GEM-P800 - page 9
Preparing a Fire Escape Plan Even with the most advanc ed fire alar m s ystem, adequate protection r equires an es cape plan. To prepar e your plan, draw floor plans of your building. (space is pr ovided on the next page) Show two exits - a f ront or back door and a window from each room . (Mak e s ure each window works. You m ay need a special fir ...
-
Gemini GEM-P800 - page 10
10 Fire Protection Floorplan Draw a plan of your premis es below. Oi219c page 10 Tuesday, September 16, 1997 08:24 ...
-
Gemini GEM-P800 - page 11
Special Functions By pressing A followed by the the appropriate key, (do not press simultaneously) these special functions and features can be enabled: Easy A rm (when system is dis arm ed) The Easy Arm feature allows the s y stem to be arm ed by pressing f ollowed by . This will allow the eas y arm ing of the system by someone who is not a regular ...
-
Gemini GEM-P800 - page 12
12 The G EM-P800 is constantly monitor ing its own com ponents, as well as all c ritical services , such as AC pow er and the telephone line, to insure that it is alway s ready to provide the protection for which it was des igned. W hen a system trouble does occur , it will caution you by lighting the TROUBLE light and beeping the keypad buzz er. I ...
-
Gemini GEM-P800 - page 13
13 Sy stem Troubles Keypad Beeps or Flashes Zone light ON System Tr ouble Condition Action 2 Beeps 2 Fire Trouble A problem has been detected in the Fire Circuit. Call installing company for serv ice. 2 Beeps 3 W ireless Receiver Trouble A problem has been detected w ith the wireless receiv er. Call installing company for serv ice. 2 Beeps ...
-
Gemini GEM-P800 - page 14
Your Installer has assigned a User 1 Code which can be used to not only Arm and Dis arm the system, but also to enter the User Program Mode, where y ou can program other user c odes. The following explains how you will use this code to progr am or erase additional user codes . Entering the User Program Mode Press followed by and enter the Us er 1 c ...
-
Gemini GEM-P800 - page 15
A mbush Code - In the event that y ou are forc ed by an intruder to disarm your system, this special code c an be used to disarm the system , and simultaneously send a silent alarm to Central Station. If y our s ystem has the Am bu sh f eatu re enabled, the code assigned as the User 8 code will function as y o ur Ambush Code. A rming / Disarming - ...
-
Gemini GEM-P800 - page 16
NA PCO LIM I TED WA RRA NTY THE FOLL OW ING STATEM ENT IS REQUI RED BY THE F C C . This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the m anufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to ...
Hai una domanda su Gemini GEM-P800?
Utilizza il modulo sottostante
Se non hai risolto il problema con Gemini GEM-P800 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Gemini GEM-P800 è probabile che voglia condividere il modo di risolverlo.