Manuale per l’uso Cisco Systems OC-12/STM-14

20 pagine 0.33 mb
Scarica

Vai alla pagina of 20

Summary
  • Cisco Systems OC-12/STM-14 - page 1

    Corporate Headquarters: Copyright © 2004 Cisco Systems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Cisco IOS Software Configuration for the 1-Port Channelized OC-12/STM-4 (DS3) Line Card This document describes the software con figurat io n procedure for the 1- port channelized OC-12/STM-4 (DS ...

  • Cisco Systems OC-12/STM-14 - page 2

    Cisco IOS Software Configuration for the 1-Port Chann eliz ed OC-12/STM -4 (DS3) Line Card Prerequisites for the 1-Port Channeliz ed OC- 1 2/ST M-4 (DS3) Line Card 2 Cisco IOS Release 12.0(8)S Prerequisites for the 1-Port Channelized OC-12/STM-4 (DS3) Line Card The Cisco 1 2000 Series Rou ter must have at least one clock and sc heduler card (CSC) i ...

  • Cisco Systems OC-12/STM-14 - page 3

    Cisco IOS Software Configuration for th e 1-Port Channelized OC-12/STM-4 (DS3) Line Card How to Configure the 1-Port Channe lized OC-12/STM-4 (DS3) Line Card 3 Cisco IOS Release 12.0(8)S (Remainder of displayed text omi tted from e xample) Ta b l e 1 sho ws the def ault OC-12 controller conf igura tion of a 1-port channeli zed OC-12/STM-4 (DS3) lin ...

  • Cisco Systems OC-12/STM-14 - page 4

    Cisco IOS Software Configuration for the 1-Port Chann eliz ed OC-12/STM -4 (DS3) Line Card How to Configure the 1-Port Channelized OC-12/STM-4 (DS3) Line Card 4 Cisco IOS Release 12.0(8)S Configuring the DS3 Serial Interface After you v e rify the OC-12 controller co nfiguration, you can conf igure the associated DS3 channel and serial interfaces o ...

  • Cisco Systems OC-12/STM-14 - page 5

    Cisco IOS Software Configuration for th e 1-Port Channelized OC-12/STM-4 (DS3) Line Card How to Configure the 1-Port Channe lized OC-12/STM-4 (DS3) Line Card 5 Cisco IOS Release 12.0(8)S The prompt changes to inter face conf igu ration mode. The follo wing e xample is for a 1-port channelized OC-12/STM-4 (DS3) line card in chassis slot 1: Router(co ...

  • Cisco Systems OC-12/STM-14 - page 6

    Cisco IOS Software Configuration for the 1-Port Chann eliz ed OC-12/STM -4 (DS3) Line Card How to Configure the 1-Port Channelized OC-12/STM-4 (DS3) Line Card 6 Cisco IOS Release 12.0(8)S Y ou can connect the local (near -end) DS3 port to the remote (f ar-end) DS3 port using a third- party DSU. Then use the telnet command from the local DS3 port to ...

  • Cisco Systems OC-12/STM-14 - page 7

    Cisco IOS Software Configuration for th e 1-Port Channelized OC-12/STM-4 (DS3) Line Card How to Configure the 1-Port Channe lized OC-12/STM-4 (DS3) Line Card 7 Cisco IOS Release 12.0(8)S The Cisco Remote Connection Management feature uses two Cisco-proprietary DS3 C-bit parity Far -End Alarm and Cont rol (FEAC) messages that ar e not us ed in the A ...

  • Cisco Systems OC-12/STM-14 - page 8

    Cisco IOS Software Configuration for the 1-Port Chann eliz ed OC-12/STM -4 (DS3) Line Card How to Configure the 1-Port Channelized OC-12/STM-4 (DS3) Line Card 8 Cisco IOS Release 12.0(8)S Enabling Payload Scrambling Payload (data) scrambling con verts th e data receive d by the lo cal or remote DS3 ports from an y of the three supported thi rd-part ...

  • Cisco Systems OC-12/STM-14 - page 9

    Cisco IOS Software Configuration for th e 1-Port Channelized OC-12/STM-4 (DS3) Line Card How to Configure the 1-Port Channe lized OC-12/STM-4 (DS3) Line Card 9 Cisco IOS Release 12.0(8)S Last clearing of "show interface" counters 1d16h Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits ...

  • Cisco Systems OC-12/STM-14 - page 10

    Cisco IOS Software Configuration for the 1-Port Chann eliz ed OC-12/STM -4 (DS3) Line Card How to Configure the 1-Port Channelized OC-12/STM-4 (DS3) Line Card 10 Cisco IOS Release 12.0(8)S – show contr ollers oc12 slot/port:c hannel# V erify the Cisco Remote Connection Management configuration b y entering the show contr ollers oc12 slot/port:c h ...

  • Cisco Systems OC-12/STM-14 - page 11

    Cisco IOS Software Configuration for th e 1-Port Channelized OC-12/STM-4 (DS3) Line Card How to Configure the 1-Port Channe lized OC-12/STM-4 (DS3) Line Card 11 Cisco IOS Release 12.0(8)S FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF ................ FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF ................ Router • Use the show protocol ...

  • Cisco Systems OC-12/STM-14 - page 12

    Cisco IOS Software Configuration for the 1-Port Chann eliz ed OC-12/STM -4 (DS3) Line Card How to Configure the 1-Port Channelized OC-12/STM-4 (DS3) Line Card 12 Cisco IOS Release 12.0(8)S Using Loopback Commands The 1-port channelized OC-12 /STM-4 (DS3) line card supports loop back modes for both the OC-1 2 controller and for each of the associ at ...

  • Cisco Systems OC-12/STM-14 - page 13

    Cisco IOS Software Configuration for th e 1-Port Channelized OC-12/STM-4 (DS3) Line Card How to Configure the 1-Port Channe lized OC-12/STM-4 (DS3) Line Card 13 Cisco IOS Release 12.0(8)S • Line—This loopback mode loops data from the receiv e path to the transmit path at the mux/demux part on the line card, returning al l recei ved data at the ...

  • Cisco Systems OC-12/STM-14 - page 14

    Cisco IOS Software Configuration for the 1-Port Chann eliz ed OC-12/STM -4 (DS3) Line Card How to Configure the 1-Port Channelized OC-12/STM-4 (DS3) Line Card 14 Cisco IOS Release 12.0(8)S set to internal o n the local OC-12 controller in slot 1 with IP address 10.0.0 .2. Clock source is set to line on the remote OC-12 controller in slot 1 with IP ...

  • Cisco Systems OC-12/STM-14 - page 15

    Cisco IOS Software Configuration for th e 1-Port Channelized OC-12/STM-4 (DS3) Line Card How to Configure the 1-Port Channe lized OC-12/STM-4 (DS3) Line Card 15 Cisco IOS Release 12.0(8)S Entering Errors in BER Tests T o insert intentional erro rs into the BER test stream, use the follo wing command syntax: bert errors [ no-of-err ors ], where the ...

  • Cisco Systems OC-12/STM-14 - page 16

    Cisco IOS Software Configuration for the 1-Port Chann eliz ed OC-12/STM -4 (DS3) Line Card How to Configure the 1-Port Channelized OC-12/STM-4 (DS3) Line Card 16 Cisco IOS Release 12.0(8)S The follo wing example sho ws the information of a BER test that is still in prog ress: Router# show controller OC12 1/0:1 bert Interface Serial1/0:1 (DS3 port 1 ...

  • Cisco Systems OC-12/STM-14 - page 17

    Cisco IOS Software Configuration for th e 1-Port Channelized OC-12/STM-4 (DS3) Line Card Configuration Examples for the 1-Port Channelized OC-12/STM-4 (DS3) Line Card 17 Cisco IOS Release 12.0(8)S Configuration Examples for the 1-Port Channelized OC-12/STM-4 (DS3) Line Card Figure 2 sho ws two 1-port channelized OC-12/S T M-4 (DS3) line card conf i ...

  • Cisco Systems OC-12/STM-14 - page 18

    Cisco IOS Software Configuration for the 1-Port Chann eliz ed OC-12/STM -4 (DS3) Line Card Configuration Examples for the 1-Port Channelized OC- 12/STM- 4 (D S3) Line Card 18 Cisco IOS Release 12.0(8)S Figur e 2 1 -P ort Channelized OC-12/S T M-4 (DS3 ) L i n e Ca rd In te rop e ra b i l it y Di a gra m The following e xample shows a typical conf i ...

  • Cisco Systems OC-12/STM-14 - page 19

    Cisco IOS Software Configuration for th e 1-Port Channelized OC-12/STM-4 (DS3) Line Card Additional References 19 Cisco IOS Release 12.0(8)S Additional References The follo wing sections provide r eferences related to the 1-port channelized OC-12/STM-4 (DS3) line card. Related Documents Technical Assistance Copyright © 200 4 Cisco Syst ems, Inc. A ...

  • Cisco Systems OC-12/STM-14 - page 20

    Cisco IOS Software Configuration for the 1-Port Chann eliz ed OC-12/STM -4 (DS3) Line Card Additional References 20 Cisco IOS Release 12.0(8)S ...

Fabbricante Cisco Systems Categoria Network Router

I documenti che otteniamo dal fabbricante del dispositivoCisco Systems OC-12/STM-14 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Cisco Systems
- manuali per l’uso OC-12/STM-14
- schede prodotto Cisco Systems
- opuscoli
- o etichette energetiche Cisco Systems OC-12/STM-14
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Cisco Systems OC-12/STM-14.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Cisco Systems OC-12/STM-14, manuali di manutenzione, brevi manuali o manuali utente Cisco Systems OC-12/STM-14. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Cisco Systems OC-12/STM-14.

Manuali per l’uso simili

Manuale completo del dispositivo Cisco Systems OC-12/STM-14, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Cisco Systems OC-12/STM-14 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Cisco Systems OC-12/STM-14.

Il manuale per l’uso completo Cisco Systems, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Cisco Systems OC-12/STM-14 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Cisco Systems OC-12/STM-14, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Cisco Systems OC-12/STM-14 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Cisco Systems OC-12/STM-14 - che ci dovrebbe aiutare nei primi passi durante l'uso Cisco Systems OC-12/STM-14
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Cisco Systems OC-12/STM-14
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Cisco Systems OC-12/STM-14 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Cisco Systems OC-12/STM-14?

Utilizza il modulo sottostante

Se non hai risolto il problema con Cisco Systems OC-12/STM-14 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Cisco Systems OC-12/STM-14 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)