Italiano dropdown-ico

Manuale per l’uso Outback Power Systems FW-SP-R

22 pagine 0.57 mb
Scarica

Vai alla pagina of 22

Summary
  • Outback Power Systems FW-SP-R - page 1

    Sur ge P r ot ec tor FW -SP-A CA FW -SP-250 FW -SP-R U ser ’ s Guide Includes M ounting and Installation ...

  • Outback Power Systems FW-SP-R - page 2

    About OutBack P ower S ystems OutBack P ower Systems is a leader in advanced ener gy conversion t echnology . Our products include true sine wave in verter/chargers, maximum power point char ge controllers, syst em com- munication components, as well as br eaker panels, breakers, accessories, and assembled syst ems. Notice of Cop yright FLEXware Su ...

  • Outback Power Systems FW-SP-R - page 3

    2 W arranty I ntroduction Dear OutBack Customer , Thank you for y our purchase of OutBack products. We make every e or t to assur e our power con- version products will give y ou long and reliable ser vice for your r enewable energy system. As with any manufactured device , repairs might be needed due to damage , inappropriate use, or unintentio ...

  • Outback Power Systems FW-SP-R - page 4

    OUTBACK FLEX ware Surge P rotector INST ALLA TION GUIDELINES AND SAFET Y INSTRUC TIONS This product is intended to be installed as part of a permanently grounded electrical system . • The FLEXware Sur ge P rotector is designed f or indoor installation or installation inside a weatherproof enclosure . • F or full system protection, one FLEXware ...

  • Outback Power Systems FW-SP-R - page 5

    INTRODUC TION The OutBack FLEXware Sur ge Pr otec tor connects to the f ollowing FX Ser ies Inverter/Charger por ts: • DC+ • DC- • AC HO T IN • AC NEUTRAL IN • AC HO T OUT • AC NEUTRAL OUT • GROUND The FLEXware Sur ge Pr otec tor is desig ned to protect the FX’ s sensitive components from excessively high v oltages (e.g., electrical ...

  • Outback Power Systems FW-SP-R - page 6

    The FLEX ware Surge P rotector Speci cations LEDs • AC TIVE lights are y ellow (power is present). • ERROR lights are red (pr otection in that circuit is compromised , replacing the surge pr otec tor is recommended). • F or the ERR OR light to show , its circuit must be pow ered; its ACTIVE light will also glow. Figur e 3 : Surge P rotecto ...

  • Outback Power Systems FW-SP-R - page 7

    FW-SP -ACA The FW-SP -ACA consists of an FW-A CA with an included surge prot ector and is installed onto an FX Series Inver ter/Char ger . Figur e 4: FLEXware Sur ge Pr otec tor -ACA LEDs Underside screw secures FW-SP -ACA to FX Phillips screw secur es FW-SP -ACA bracket and surge prot ector board to the FW-SP -ACA Underside screw secures FW-SP -AC ...

  • Outback Power Systems FW-SP-R - page 8

    (1) Remove the DC C or T urbo (secured by four Phillips corner screws) (2) Remove the DC battery caps (under the DCC or T urbo) (3) Remove the AC Wiring Compartment plastic cover (secured with two Phillips screws) (5) Remove the AC C on- duit Plate, which slides up and out from the FX (4) Remove these two M5 hex bolts from the FX Figur e 5 : Removi ...

  • Outback Power Systems FW-SP-R - page 9

    (7) Remove the appropriate knockouts for the individual power application. Note that knockouts should be scored  rst with a utility knife and then removed . The dual, concentric knock out on the back o ers openings for the FW500, FW1000, PS2 and PS4 AC enclosures . (9) The FW-SP-ACA slides ont o the FX in the same location as the now remov ed ...

  • Outback Power Systems FW-SP-R - page 10

    9 (11) Inser t a bushing into the AC enclosur e (it is not critical that this bushing line up precisely with the FW-SP -ACA); if  exible cable is used instead of an enclosure , appropriate strain relief is r equired. Screws (included) secure the FW -SP-A CA to an FX FW-SP -ACA slides down FX slots Figur e 7: T op view of FW-SP-ACA installed on a ...

  • Outback Power Systems FW-SP-R - page 11

    FW-SP -250 The FW-SP -250 is a two-piece combined FLEXware 250 top cover and FLEX ware Surge P rotector . I t replaces an existing FLEXwar e 250 cover , attaching at the AC end of the FLEXware 250. Pr ocedure The FLEXware 250 A C should already be installed (see FW250 AC instructions) and all AC and DC power shut o . (4) Replace the standard FLE ...

  • Outback Power Systems FW-SP-R - page 12

    (8) Route the FW-SP -250 wires through to the A C Wiring Compartment and to the batter y lugs. (9) Secure the surge pr otec tor’ s wiring in the appropriate locations and replace the various plastic covers as per the wiring instructions on page 16. 11 (5) Install the top section of the cover contain- ing the surge prot ector  rst. (6) The lowe ...

  • Outback Power Systems FW-SP-R - page 13

    Figur e 11: FW-ACA (2) Remove the FW-A CA plastic cover (secured with two Phillips screws) (3) Remove the FW- ACA Bracket (secured with one Phillips screw); if a damaged FLEXware Sur ge Pr otec tor is being replaced, r emove it by disengaging the locating pin FW-ACA housing Locating pin FW-SP -R (REPLACEMENT ) for the FW -SP-A CA or the FW-A CA An ...

  • Outback Power Systems FW-SP-R - page 14

    1/ 3/07 The locating pin on the FW-ACA bracket  ts in this slot (4) P ass the FW-SP -R wires through the FW - ACA Bracket opening, lining up the locating pin with the slot on the surge prot ector . FW-SP -R LEDs Figur es 12: FW-SP -R and FW-ACA Bracket 13 ...

  • Outback Power Systems FW-SP-R - page 15

    (5) With the FW-SP-R attached t o the FW-ACA Bracket, hold the ends of the FW-SP -R wires and slide it and the bracket back inside the FW-ACA to its original location. NO TE: The FW-SP -R slides into a double slot at the bottom of the FW-ACA. The LEDs should be level with the top of the FW-A CA housing. Figur e 13: FW-SP -R installed inside the FW- ...

  • Outback Power Systems FW-SP-R - page 16

    (6) When the new surge protector board has been secured to the FW-SP -250 cover , reinstall the FW-SP -250 as shown on pages 10-11. (3) Remove the FW-SP -250 (secured by six Phillips screws). (2) Remove the AC Wiring Compartment cover (secured by two Phillips screws). (1) Remove the DC C or T urbo cover (secured by f our Phillips screws) and the DC ...

  • Outback Power Systems FW-SP-R - page 17

    Wiring and C onnec ting the FLEX ware Surge Pr otec tor With the FW-SP -250 or FW-SP-ACA secur ed, connect all AC and DC wiring as well as any HUB, MA TE, A UX, and BA T TERY TEMP cables. • Install all AC and DC power cables  rst followed by the sur ge protector wires in their appropriate locations; each wire is labeled on the shrink- wrapped ...

  • Outback Power Systems FW-SP-R - page 18

    • Install the various covers in this order with the DCC or Turbo last: (1) DC battery terminals (2) FW-ACA (if used) (3) AC Wiring Compar tment Figur e 16: After wiring, install all covers . The surge prot ector ’ s DC + and DC- cables and the BA T T TEMP sensor cable pass under this rubber bushing The system can now be po wered up • DC power ...

  • Outback Power Systems FW-SP-R - page 19

    18 FLEX ware ™ Surge P rotector Limited W arranty OutBack P ower Systems , Inc. (“OutBack ”) provides a limit ed warranty (“ Warranty ”) against defects in materials and workmanship for its FLEXware Sur ge Pr otec tor P roducts (“Product”) if installed for use with OutBack FX Series Inverter/Chargers in  xed location applications. ...

  • Outback Power Systems FW-SP-R - page 20

    19 1. P roof- of-purchase in the f or m of a copy of the original P roduct purchase invoice or r eceipt con rming the Pr oduct model number and serial number ; 2. OutBack issued warranty cer ti cate f or the FX Series I n verter/Charger used with the Pr oduc t; 3. Description of the problem; and 4. Shipping address f or the replacement equipm ...

  • Outback Power Systems FW-SP-R - page 21

    Surge P rotector Limited W arranty Registra tion 20 Revision 2007-06-20 Surge P rotector Limited W arrant y Registration Complete this form to request a Limited W arranty , and return it to: Outback P ower Systems Inc. 19009 62nd Ave . NE Arlington, W A 98223 Note: A Limited Warranty Cer ti cate will only be issued if this Registration Card is r ...

  • Outback Power Systems FW-SP-R - page 22

    900-0089-01-00 REV A European Sales O c e Barcelona, España (+34) 600-843-845 19009 62nd Avenue NE Arlington, W A USA (+1) 360-435-6030 www.outbackpower .com ...

Fabbricante Outback Power Systems Categoria Surge Protector

I documenti che otteniamo dal fabbricante del dispositivoOutback Power Systems FW-SP-R possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Outback Power Systems
- manuali per l’uso FW-SP-R
- schede prodotto Outback Power Systems
- opuscoli
- o etichette energetiche Outback Power Systems FW-SP-R
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Outback Power Systems FW-SP-R.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Outback Power Systems FW-SP-R, manuali di manutenzione, brevi manuali o manuali utente Outback Power Systems FW-SP-R. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Outback Power Systems FW-SP-R.

Manuali per l’uso simili

Manuale completo del dispositivo Outback Power Systems FW-SP-R, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Outback Power Systems FW-SP-R dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Outback Power Systems FW-SP-R.

Il manuale per l’uso completo Outback Power Systems, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Outback Power Systems FW-SP-R - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Outback Power Systems FW-SP-R, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Outback Power Systems FW-SP-R che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Outback Power Systems FW-SP-R - che ci dovrebbe aiutare nei primi passi durante l'uso Outback Power Systems FW-SP-R
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Outback Power Systems FW-SP-R
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Outback Power Systems FW-SP-R in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Outback Power Systems FW-SP-R?

Utilizza il modulo sottostante

Se non hai risolto il problema con Outback Power Systems FW-SP-R con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Outback Power Systems FW-SP-R è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)