-
Calculated Industries Home ProjectCalc - page 1
...
-
Calculated Industries Home ProjectCalc - page 2
T ABLE OF C ONTENTS Key Definitions ................................1 Basic Function Keys ..................................1 Dimensional Unit Keys ..............................2 Convert Key Functions ..............................3 Memory ....................................................4 Entering Square or Cubic ..........................4 Fr ...
-
Calculated Industries Home ProjectCalc - page 3
P OCKET R EFERENCE G UIDE - 1 Basic Function Keys o - On/Clear Key T urns power on. Pressing once clears the display . Pressing twice clears all temporary values. O - Off T urns all power off, clearing all non- permanent registers. + – x ÷ = Arithmetic operation keys. 0 - 9 and • Digits used for keying in numbers. % - Per cent (%) Four-functio ...
-
Calculated Industries Home ProjectCalc - page 4
Dimensional Unit Keys y - Y ards K ey Enters or converts to Y ards. f - Feet Key Enters or converts to Feet as whole or decimal numbers. Also used with the i and / keys for entering Feet-Inch-Fraction values (e.g., 6 f 9 i 1 / 2 ). Repeated presses during conversions toggle between Feet-Inch-Fractions and Decimal Feet. i - Inch Ke y Enters or conve ...
-
Calculated Industries Home ProjectCalc - page 5
...
-
Calculated Industries Home ProjectCalc - page 6
Memory Ç + (M+) - Adds or stores a value in the semi-permanent memory (e.g., 1 5 0 Ç + ). Semi-permanent means the value is cleared when the calculator is turned off. Ç – Ç + (M-) - Subtracts a value from the semi-permanent Memory (e.g., 1 5 0 Ç – Ç + subtracts 150 from the memory). Ç = (MR) - Recalls Memory value (e.g., if 150 has been ...
-
Calculated Industries Home ProjectCalc - page 7
P OCKET R EFERENCE G UIDE - 5 Fraction Resolution Y our calculator is set to display Fractional values to the nearest 16th of an Inch (default setting). Press Ç / to access the fraction resolution setting. Repeated presses of / will then revolve through the available settings: 1/16, 1/32, 1/64, 1/2, 1/4 and 1/8. Press o to exit. Project K eys p - ...
-
Calculated Industries Home ProjectCalc - page 8
(Cont’d) t - Tile Finds the number of tiles, based on an entered or calculated area. Repeated presses will scroll between numbers of tiles for various “stan- dard” tile sizes (18”, 16”, 13”, 12”, 10”, 8”, 6”, 4”, 2”, 1” and 24”). Note: Tile sizes shown in Inches, not Square Inches. In other words, a 6” tile is really 6 ...
-
Calculated Industries Home ProjectCalc - page 9
P OCKET R EFERENCE G UIDE - 7 Linear Con versions Convert 15 Feet 9-1/16 Inches to other units of measure. KEYSTROKE DISPLA Y o 0. 1 5 f 9 i 1 / 1 6 15 FEET 9-1/16 INCH Ç f 15.75521 FEET Ç i 189.0625 INCH Ç y 5.251736 YD Ç m 4.802187 M Convert Decimal Inches to Fractional Inches. KEYSTROKE DISPLA Y o 0. 1 4 • 7 9 3 i 14.793 INCH Ç i 14-13/16 ...
-
Calculated Industries Home ProjectCalc - page 10
P OCKET R EFERENCE G UIDE - 8 Square and Cubic Con versions Convert 25 Square Feet to other Square dimensions. KEYSTROKE DISPLA Y o 0. 2 5 f f 25. SQ FEET Ç y 2.777778 SQ YD Ç m 2.322576 SQ M Convert 25 Cubic Feet to Cubic Y ards. KEYSTROKE DISPLA Y o 0. 2 5 f f f 25. CU FEET Ç y 0.925926 CU YD ...
-
Calculated Industries Home ProjectCalc - page 11
P OCKET R EFERENCE G UIDE - 9 Basic Dimensional Math KEYSTROKE DISPLA Y o 0. Adding Dimensions: 1 0 i + 2 f 5 i = 3 FEET 3 INCH Subtracting Dimensions: 5 f – 1 i 3 / 4 = 4 FEET 10-1/4 INCH Dividing Dimensions: 1 0 f ÷ 1 i 1 / 4 = 96. Multiplying Dimensions/Waste Factor Allowance: 1 5 0 f f + 1 0 % 165. SQ FEET Finding Area/Square Feet: 2 f x 1 f ...
-
Calculated Industries Home ProjectCalc - page 12
Paint: Gallons, Quarts or Pints of How many quarts of paint will you need to cover a wall measuring 12’ x 8’? How many pints? How many gal lons? KEYSTROKE DISPLA Y o 0. 1 2 f x 8 f = 96. SQ FEET p 1.10 QT p 2.19 P t p 0.27 GL W allpaper: Rolls of Find the number of wallpaper rolls needed for a wall measuring 8’ x 12’. KEYSTROKE DISPLA Y o 0 ...
-
Calculated Industries Home ProjectCalc - page 13
P OCKET R EFERENCE G UIDE - 11 Tiles: Number of How many tiles do you need to cover a floor measuring 10’ x 15’? Find the number of tiles in various sizes. Also, add a 10% waste allowance, in case you need extra tile. Note: After converting to Tile, press the t key until you reach the desired tile size. (The Home ProjectCalc lists 1 1 of the mo ...
-
Calculated Industries Home ProjectCalc - page 14
P OCKET R EFERENCE G UIDE - 12 Carpet: Length of Find the quantity of carpet needed to cover a floor that measures 12’ 6” x 10’ in area. KEYSTROKE DISPLA Y o 0. 1 2 f 6 i x 1 0 f = 125. SQ FEET c 13.89 SQ YD c 10.42 FEET (12 Ft ROLL ) c 9.62 FEET (13 Ft ROLL ) c 8.33 FEET (15 Ft ROLL ) Concrete: Bags of Find the number of bags of concrete for ...
-
Calculated Industries Home ProjectCalc - page 15
P OCKET R EFERENCE G UIDE - 13 Cost of Concrete How much will 216 Cubic Feet of con- crete cost, if the Cost Per Cubic Y ard is quoted at $50? KEYSTROKE DISPLA Y o 0. 2 1 6 f f f 216. CU FEET Ç y 8. CU YD x 5 0 Ç • (Cost) 400. 00 (It’ll cost approx. $400) FINDING THE COST OF MA TERIALS ...
-
Calculated Industries Home ProjectCalc - page 16
P OCKET R EFERENCE G UIDE - 14 Reset If your calculator should ever “lock up,” press Reset - a small hole located above the C key/upper right - using the end of a paper clip. Auto Shut-Off and Batteries Auto Shut-Off: After 8-12 minutes of non-use. Batteries Included: T wo LR-43 batteries. Battery-Life: 575 hours of actual use. T o replace the ...
-
Calculated Industries Home ProjectCalc - page 17
P OCKET R EFERENCE G UIDE - 15 W arranty , Repair and Return Information Return Guidelines: 1. Please read the Warranty in this User's Guide to determine if your Calculated Industries product remains under warranty before calling or return- ing any device for evaluation or repairs. 2. If your product won't turn on, check the batteries as ...
-
Calculated Industries Home ProjectCalc - page 18
P OCKET R EFERENCE G UIDE - 16 W arranty Repair Service – U.S.A. Calculated Industries (“CI”) warrants this product against defects in materials and workmanship for a period of one (1) year from the date of original consumer purchase in the U.S. If a defect exists during the warranty period, CI, at its option, will either repair (using new or ...
-
Calculated Industries Home ProjectCalc - page 19
P OCKET R EFERENCE G UIDE - 17 Non-W arranty Repair Service – U.S.A. Non-warranty repair covers service beyond the warranty period, or service requested due to dam- age resulting from misuse or abuse. Contact Calculated Industries at the number listed above to obtain current product repair information and charges. Repairs are guaranteed for 90 da ...
-
Calculated Industries Home ProjectCalc - page 20
P OCKET R EFERENCE G UIDE - 18 Disclaimer CI MAKES NO WARRANTY OR REPRESENT A- TION, EITHER EXPRESS OR IMPLIED, WITH RESPECT T O THE PRODUCT’S QUALITY , PER- FORMANCE, MERCHANT ABILITY , OR FITNESS FOR A P ARTICULAR PURPOSE. AS A RESUL T , THIS PRODUCT , INCLUDING BUT NOT LIMITED TO, KEYSTROKE PROCEDURES, MA THEMA TI- CAL ACCURACY AND PREPROGRAMM ...
-
Calculated Industries Home ProjectCalc - page 21
This equipment has been certified to comply with the limits for a Class B computing device, pur- suant to Subpart J of Part 15 of FCC rules. Calculated Industries, a leading manufacturer of special-function calculators and digital measuring instruments, is always looking for new product ideas in these areas. If you have an idea, or a suggestion for ...
-
Calculated Industries Home ProjectCalc - page 22
Software copyrighted and licensed to Calculated Industries, by Construction Master T echnologies, LLC, 2007. User ’s Guide copyrighted by Calculated Industries, 2007. ProjectCalc® and Calculated Industries® are registered trademarks of Calculated Industries, Inc. ALL RIGHTS RESERVED Designed in the U.S.A. U.S. Patent 6,721,623 8/07 PRG8510E-A ...
Hai una domanda su Calculated Industries Home ProjectCalc?
Utilizza il modulo sottostante
Se non hai risolto il problema con Calculated Industries Home ProjectCalc con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Calculated Industries Home ProjectCalc è probabile che voglia condividere il modo di risolverlo.