Italiano dropdown-ico

Manuale per l’uso Brinkmann Pro Series 2500

32 pagine 2.11 mb
Scarica

Vai alla pagina of 32

Summary
  • Brinkmann Pro Series 2500 - page 1

    MAXIMUM SIDE BURNER LOAD = 15 lbs. 1. Read and follow all warnings and instructions in owner’s manual before lighting. 2. Open lid before lighting burner. 3. Make sure all control knobs are in the OFF position. 4. Select the burner to be lit. Push and turn the control knob of that burner to HIGH. 5. Press the electronic igniter and hold for 3-5 s ...

  • Brinkmann Pro Series 2500 - page 2

    WE W ANT YOU T O ASSEMBLE AND USE YOUR GRILL AS SAFEL Y AS POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO A TTRACT YOUR A TTENTION TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL. WHEN YOU SEE THE SAFETY ALERT SYMBOL P A Y CLOSE A TTENTION TO THE INFORMA TION WHICH FOLLOWS! READ ALL SAFETY W ARNINGS AND INSTRUCTIONS CAREFULL Y BEFOR ...

  • Brinkmann Pro Series 2500 - page 3

    2 W ARNING • Never use natural gas in a unit designed for liquid propane gas. • Never use charcoal briquets or lighter fluid in a gas grill. • Leak test all connections before first use, even if grill was purchased fully assembled and after each tank refill. • Never check for leaks using a match or open flame. CAUTION! Strong odors, colds, ...

  • Brinkmann Pro Series 2500 - page 4

    CYLINDER SPECIFICA TIONS: When purchasing or exchanging a cylinder for your gas grill, it must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the National Standard of Canada, CAN/CSA-B339 as applicable with a listed over-filling prevention device (OPD). 3 W ARNI ...

  • Brinkmann Pro Series 2500 - page 5

    4 The cylinder must also be equipped with: • A shut-off valve terminating in a T ype 1 gas cylinder valve outlet. • A T ype 1 valve that prevents gas flow until a positive seal is obtained. • An arrangement for vapor withdrawal. • A collar to protect the cylinder shut-off valve. • A safety relief device having direct communication with th ...

  • Brinkmann Pro Series 2500 - page 6

    FILLING THE LP GAS CYLINDER: • Allow only qualified LP gas dealers to properly fill or repair your LP gas cylinder . • New tanks should be purged prior to filling; inform LP gas dealer if you are using a new tank. • DO NOT allow the cylinder to be filled beyond 80% capacity . Over-filled tanks can create a dangerous condition. Over-filled tan ...

  • Brinkmann Pro Series 2500 - page 7

    6 W ARNING • Never use your grill without leak testing all gas connections and hoses. See the section on "Leak T esting" in this manual for proper procedures. The pressure regulator and hose assembly supplied with your gas grill is designed to work with an LP gas supply cylinder . • DO NOT attempt to connect it to any other fuel suppl ...

  • Brinkmann Pro Series 2500 - page 8

    LEAK TESTING: T o prevent fire or explosion hazard: • DO NOT smoke or permit ignition sources in the area while conducting a leak test. • Perform test OUTDOORS only in a well ventilated area. • Never perform a leak test with a match or open flame. • Never perform a leak test while the grill is in use or while grill is still hot. WHEN TO PER ...

  • Brinkmann Pro Series 2500 - page 9

    W ARNING 8 6. Check each place listed (A -K) for growing bubbles which indicates a leak. 7. T urn OFF gas supply at cylinder valve. 8. T urn on control knobs to release gas pressure in hose. 9. T urn control knobs to OFF position. 10. T ighten any leaking connections. 1 1. Repeat soapy water test until no leaks are detected. DO NOT use the grill if ...

  • Brinkmann Pro Series 2500 - page 10

    LIGHTING INSTRUCTIONS: Follow the instructions exactly . 1. OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside the grill. An explosion could occur if grill lid is down. 2. Check that all burner control knobs and the cylinder valve are turned to the OFF position. 3. T urn on the fuel supply by rotating the ...

  • Brinkmann Pro Series 2500 - page 11

    LIGHTING THE SIDE BURNER: 1. Open lid to the side burner before lighting. 2. T urn on the side burner by pressing in and rotating the control knob to the HIGH position. 3. Press and hold the igniter button on the main control panel for 3-5 seconds until the burner ignites. 4. If burner does not ignite immediately , turn the burner control knob to O ...

  • Brinkmann Pro Series 2500 - page 12

    11 OPERA TING THE GRILL: Never use Charcoal or Lighter Fluid inside your Gas Grill. Read and follow all warnings and instructions contained in the preceding sections of this manual. BREAKING IN YOUR GRILL: • In manufacturing and preserving the components of your grill, oil residue may be present on the burner and cooking surfaces of your grill. ? ...

  • Brinkmann Pro Series 2500 - page 13

    ROTISSERIE COOKING: • Y our grill was pre-drilled from factory to include mounting holes for a Brinkmann rotisserie (sold separately). Do not use a rotisserie not specifically manufactured for this grill. • Read and follow all instructions provided with the rotisserie. Save instructions for future reference. • Do not use the side burner when ...

  • Brinkmann Pro Series 2500 - page 14

    TRANSPORTING AND STORAGE: • Never move a grill when it is hot or when objects are on the cooking surfaces. • Make sure that cylinder valve is shut off. After moving the grill check that all gas connections are free of leaks. Refer to instructions for leak test on page 7 of this manual. • DO NOT store a spare LP gas cylinder (filled or empty) ...

  • Brinkmann Pro Series 2500 - page 15

    CLEANING AND MAINTENANCE: • For safe grilling and peak performance of your grill, perform these checks at least twice per year or after extended periods of storage. HARDW ARE • Be sure to tighten up all hardware (nuts, bolts, screws, etc.) at least twice per year . CASTINGS • Remove the cooking grills, heat shields, and burners from inside yo ...

  • Brinkmann Pro Series 2500 - page 16

    TROUBLE SHOOTING: Problem: Possible Causes: • Burner will not light 1. Check LP cylinder fuel level. 2. Bad electrode spark. Check to see if the grill will “ match light. ” (See Page 9) Electrode or collector may need adjustment. 3. Burner may not be properly seated. 4. Burner may be obstructed. 5. The cylinder valve may be closed. 6. Regulat ...

  • Brinkmann Pro Series 2500 - page 17

    16 • T o protect your grill from excessive rust, the unit must be kept clean and covered at all times when not in use. A grill cover may be ordered directly from Brinkmann by calling 1-800-468-5252 or 1-800-527-0717. • W ash cooking grills and heat shields with hot, soapy water , rinse well and dry . Lightly coat cooking grill with vegetable oi ...

  • Brinkmann Pro Series 2500 - page 18

    ASSEMBL Y INSTRUCTIONS READ ALL SAFETY W ARNINGS & ASSEMBL Y INSTRUCTIONS CAREFULL Y BEFORE ASSEMBLING OR OPERA TING YOUR GRILL. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT . The following provided tools are required to assemble this Brinkmann Pro Series 2500 Grill: • Flathead Screwdriver • Hex Nut Wrench 17 1 Side Shelf ...

  • Brinkmann Pro Series 2500 - page 19

    50 100 200 300 400 500 ° F OFF HIGH LOW OFF HIGH LOW OFF HIGH LOW OFF HIGH LOW OFF HIGH LOW OFF HIGH LOW M A X IM U M S I D E B U R N E R L O A D = 1 5 l b s . 1 . R e a d a n d f o l lo w a l l w a r n in g s a n d i n s t r u c t i o n s i n o w n e r ’ s m a n u a l b e f o r e l ig h t in g . 2 . O p e n l i d b e f o r e l i g h t i n g s i ...

  • Brinkmann Pro Series 2500 - page 20

    19 8 M6 X 12mm bolts 8 M6 X 20mm bolts 12 M6 X 50mm bolts 1 AA /1.5V Alkaline battery P AR TS CARD CONTENTS Make sure you have all items listed under P ARTS LIST and P ARTS BAG CONTENTS before you begin the installation process. Y our Parts Bag will include: M6 X 12mm bolts M6 X 20mm bolts M6 X 50mm bolts AA /1.5V Alkaline battery Wheel washers Whe ...

  • Brinkmann Pro Series 2500 - page 21

    Choose a good, cleared assembly area and get a friend to help you put your grill together . Lay cardboard down to protect grill finish and assembly area. Step 1 Assemble bottom cart panel and right side cart panel assembly by using four M6 X 50mm bolts (hand tighten only at this point). Step 2 Assemble bottom cart panel and left side cart panel ass ...

  • Brinkmann Pro Series 2500 - page 22

    help of a friend, turn the cart over , try to minimize the stress to the side panels. Step 3 Install the wheels as illustrated, by inserting the wheel axle bolts through the wheels, washers and right side panel axle holes. T ighten axle bolts securely using hex nut wrench provided in parts pack. Step 4 Snap wheel hub caps onto the outside of wheels ...

  • Brinkmann Pro Series 2500 - page 23

    22 Step 6 Attach back cart panel by using four M6 X 50mm bolts. Note: Leave bolts hand tight until Step 8. Step 7 Attach the grease tray bracket onto the back cart panel by inserting the three tabs into the slots on the back cart panel. Grease T ray Bracket ...

  • Brinkmann Pro Series 2500 - page 24

    23 Note: When performing Step 8, Lift grill body from front and rear panels to avoid injury to hands and fingers. Step 8 With the help of a friend, place grill body assembly on grill cart. Grill body will rest on upper side sections of cart. Align bolt holes located on the outside of the grill body assembly . Secure using four M6 X12mm bolts. At th ...

  • Brinkmann Pro Series 2500 - page 25

    Step 10 Insert right side door over lower pivot (on bottom cart panel) then align door with cart frame. Depress spring pin located on top edge of door and slide door toward side cart panel until spring pin locks into hole in door bracket. Repeat for other door . Step 1 1 Attach side burner assembly to grill body assembly by inserting four M6 X 20mm ...

  • Brinkmann Pro Series 2500 - page 26

    25 Step 12 Remove the plastic cap on gas supply manifold and attach rubber gas hose to gas supply manifold. Hand tighten first, then use supplied wrench to turn brass nut an additional 1/8 turn. Important: Do not overtighten. This could damage brass fitting. W arning: Never use your grill without leak testing all gas connections and hoses. See the ...

  • Brinkmann Pro Series 2500 - page 27

    Step 15 Insert grill bottom into opening on backside of grill. Make sure to slide tray onto tracks as illustrated. Step 16 Slide grease tray into grease tray bracket located under grill bottom on backside of grill. 26 Grill Bottom Grease T ray ...

  • Brinkmann Pro Series 2500 - page 28

    Step 17 Place the porcelain coated heat shields on lower level of grill body assembly directly above burners. Step 18 Place porcelain cast iron cooking grills on support ribs directly above porcelain heat shields. Step 19 Place warming rack in slots above cast iron cooking grills. Step 20 Insert smoker box into opening on the right side of control ...

  • Brinkmann Pro Series 2500 - page 29

    28 MAXIMUM SIDE BURNER LOAD = 15 lbs. 1. Read and follow all warnings and instructions in owner ’ s manual before lighting. 2. Open lid before lighting burner. 3. Make sure all control knobs are in the OFF position. 4. Select the burner to be lit. Push and turn the control knob of that burner to HIGH. 5. Press the electronic igniter and hold for ...

  • Brinkmann Pro Series 2500 - page 30

    PROFESSIONAL SHISH-KABOB SKEWERS These heavy-duty , 18" shish-kabob skewers are extra-long for fabulous restaurant style kabobs. Made of rust resistant stainless steel to last for years. SET OF 12 812-2904-0 ACCESSORIES 29 RIB RACK Chrome-plated rack can greatly increase the cooking capacity of your grill. Holds ribs, chicken halves, potatoes ...

  • Brinkmann Pro Series 2500 - page 31

    ACCESSORIES LOOK FOR THESE AND OTHER BRINKMANN ACCESSORIES A T YOUR LOCAL RET AILER WHERE SMOKERS ARE SOLD, OR ORDER DIRECT BY CALLING 1-800-468-5252. THE UL TIMA TE 5-PIECE BBQ TOOL SET Yo u ’ ll be the envy of your fellow outdoor chefs with this ultimate BBQ tool set. It ’ s sleek ergonomic design combined with durable, heavy- gauge stainless ...

  • Brinkmann Pro Series 2500 - page 32

    8/02 140-2501-0 The Brinkmann Corporation warrants to the original purchaser that the Brinkmann Stainless Steel Pro Series 2500 TM is free from defects due to workmanship or materials for: Stainless steel and die cast parts - Lifetime Electronic ignition and burners - 1 Y ear Remaining parts - 1 Y ear The Brinkmann Corporation ’ s obligations und ...

Fabbricante Brinkmann Categoria Gas Grill

I documenti che otteniamo dal fabbricante del dispositivoBrinkmann Pro Series 2500 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Brinkmann
- manuali per l’uso Pro Series 2500
- schede prodotto Brinkmann
- opuscoli
- o etichette energetiche Brinkmann Pro Series 2500
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Brinkmann Pro Series 2500.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Brinkmann Pro Series 2500, manuali di manutenzione, brevi manuali o manuali utente Brinkmann Pro Series 2500. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Brinkmann Pro Series 2500.

Manuali per l’uso simili

Manuale completo del dispositivo Brinkmann Pro Series 2500, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Brinkmann Pro Series 2500 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Brinkmann Pro Series 2500.

Il manuale per l’uso completo Brinkmann, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Brinkmann Pro Series 2500 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Brinkmann Pro Series 2500, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Brinkmann Pro Series 2500 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Brinkmann Pro Series 2500 - che ci dovrebbe aiutare nei primi passi durante l'uso Brinkmann Pro Series 2500
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Brinkmann Pro Series 2500
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Brinkmann Pro Series 2500 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Brinkmann Pro Series 2500?

Utilizza il modulo sottostante

Se non hai risolto il problema con Brinkmann Pro Series 2500 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Brinkmann Pro Series 2500 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)