Italiano dropdown-ico

Manuale per l’uso ADT Security Services Safewatch Plus Enterpreneur Security Systems

28 pagine 0.76 mb
Scarica

Vai alla pagina of 28

Summary
  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 1

    ADT-1090-INT 7/25/00 3:12 PM Page 1 ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 2

    ADT-1090-INT 7/25/00 3:12 PM Page 2 ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 3

    Table of Contents * System Reference ................................................. 2 Operating Your System ......................................... 3 ARMING ....................................................................................... 3 Arming The System Prior To Leaving ..................................... 3 Arming The System Witho ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 4

    Zone Identification Card Space is provided for recording the areas of protection which are ;“““““““““‘““““““““’ : lndlvldual Zone Status i Ready status If lighted, zone is not secure. i ; /flight& the system is ready to be armed. Chedc doors, windows, etc. If not Iighted, one or more zones are faulted. i ! ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 5

    Operating Your System ARMING Before the control can be armed, all of the intrusion zones must be secure as indicated by the green READY indicator. If the READY indicator is off, one or more zones are faulted. The indicator(s) corresponding to the faulted zone(s) will light. Use the pull out zone I.D. card on the control station to determine the are ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 6

    ;I Turning Off the lnterlor Zones and Entrance Delay Control station key 4 may be used to turn the interior zones off prior to arming. This will allow the system to alarm instantly if the entrance door is opened, while armed. 1. Press the 4 key and hold for three seconds. 2. When interior defined zones are turned off, the corresponding Zone indicat ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 7

    DISARMING Your system is programmed with one or more entrance delay zones which allow time to enter the premises without causing an alarm. Each delay door may be programmed with a different entry time. Be sure to check with your installer. Note: If your system has the “Interior Follower” feature enabled, all interior designated zones automatica ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 8

    ALARM CONDITIONS Whenever an alarm occurs, the ALARM indicator will light, the audible alarm will sound (if applicable), and the control wilI communicate with the central station (if this option was purchased). NOTE: If upon returning to the premises it 1s discovered that an alarm has occurred, DO NOT ENTER THE PREMISES. Leave immediately and go to ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 9

    THE EMERGENCY KEYPAD PANIC ALARMS Your system may have been purchased with up to three emergency keypad panic alarms. These may be used to activate an alarm in the event of a Fire, Hold-up, or other emergency condition, as programmed by your installer. Each alarm is activated by pressing the appropriate emergency panic key (located below the numeri ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 10

    SPECIAL FEATURES The CHIME mode allows audible monitoring of zones while the system is disarmed. When the CHIME mode is active, the control station sounder will beep whenever a perimeter burglar defined zone (door, window, etc.) indicator is opened. For example, the CHIME feature will cause the control station to beep two times whenever the front d ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 11

    The bypass key (#) is used to bypass selected zones in your system. A bypassed zone will NOT be capable of activating an alarm as it is temporarily removed from your system. Bypassing (also referred to as shunting) is most commonly used to allow free movement of an area (zone or group of zones) while arming the rest of the system or to temporarily ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 12

    Your system may utilize a conventional key switch for arming and disarming the system. Arming and disarming with a key switch is performed as follows: cl 1. 2. 3. 0 1. 2. Arming Verify that the BEADY light is on. Insert your key into the key switch and turn. Hold for one second and release. The red ARMED light will blink during the exit delay cycle ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 13

    Programming Certain features of your system are programmable through the control station. The programming mode is entered by pressing key 9 and holding for three seconds, then entering the Master User Code. Other programming functions may be possible that are not detailed in this section. Consult your security representative for a list of the user ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 14

    Determine your desired new User Code or Master User Code sequence. If you make an error while programming, press the “ * ” key five times and start over from step 1. WARNING: Pressing the “ # ” or l4 * ” key while programmlng a code may result In Improper code operation, therefore you MUST return to step 1 when an error Is made. 0 1. 2. 3 ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 15

    An optional feature of your system allows you to assign a certain number of valid uses to User Code 6. After the code has been used the programmed amount of times, it automatically becomes disabled. This code may be assigned to a maintenance person, a maid, or anyone who you would like to be able to arm and disarm the system for a selected number o ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 16

    Notes ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 17

    The TEST mode commands the control station to beep continuously and light the corresponding zone indicator, each time a zone is violated. The zone indicator of each tested zone will remain lighted while each succeeding zone is tested. Testing can be performed only while the system is disarmed. Testing the system should be performed in both ELECTRIC ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 18

    FIRE DETECTION Your system may or may not include fire detection, depending upon what options were purchased, and the local codes and regulations for your area. Fire alarm systems are active 24 hours a day and cannot be turned off. A!! fire systems require regular testing and maintenance. Common household dust build-up in smoke detectors can cause ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 19

    Emergency Evacuation Plan Preparation and education are of prime importance in the prevention of fire. An emergency evacuation plan should be established BEFORE an emergency situation arises. Your system may or may not contain fire detection and notification equipment. Be sure to have your installer explain and that you fully understand exactly wha ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 20

    The purpose of heat and smoke detectors is to detect a fire in its earliest stages and sound an alarm, giving occupants more time to exit the premises before smoke reaches a dangerous level. Cl KNOW FIRE HAZARDS No detection device can protect life in all situations; therefore, safeguards should be taken to avoid such potentially dangerous situatio ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 21

    0 Smoke Detector Location Smoke detectors should be installed in accordance with theNational FireProtection Association (NFPA) Standard 74. The following is from NFPA 74: Smoke detectors shall be installed outside of each separate sleeping area in the immediate vicinity of the bedrooms and on each additional story of the family living unit includin ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 22

    Smoke Detector Placement 4 inches @lm) -_I NOTE: Allmae~~mmennts are to the closest edge of the dote&or A Smoke Detector should be located on each story. A Smoke Detector should be located between the sleeping area and the rest of the family living unit. l Indicates required smoke detector @ Indicates smoke detector is optional if door is not p ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 23

    Glossary Alarm Memory: A history of the alarm that last occurred. Arm: To turn the intrusion detection system on. Bypass: To temporarily remove a zone from operation. To Shunt a zone. Control Panel: The main system electronics housed in a metal enclosure. Control Station: The remote station used to enter instructions to the control panel such as to ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 24

    ADT-1090-INT 7/25/00 3:13 PM Page 12 ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 25

    ADT-1090-INT 7/25/00 3:13 PM Page 12 ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 26

    Notes 20 ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 27

    FCC COMPLIANCE This equipment ganerates and uses radio frequency energy and lf nU installed and used properly, that !a. In strict accordance with the rtwnufacturer’s instructions, may catae interference to radio and teledslon raceptlon. lt has been type tested and found to corrpiy with the llmks for a Class B corrputlng devtce In acwtdance with t ...

  • ADT Security Services Safewatch Plus Enterpreneur Security Systems - page 28

    MOOSE Sentrol, Inc resen~es the rtght to change specifmtmns wthout notice tJ1991 Sentrol. Inc ...

Fabbricante ADT Security Services Categoria Home Security System

I documenti che otteniamo dal fabbricante del dispositivoADT Security Services Safewatch Plus Enterpreneur Security Systems possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici ADT Security Services
- manuali per l’uso Safewatch Plus Enterpreneur Security Systems
- schede prodotto ADT Security Services
- opuscoli
- o etichette energetiche ADT Security Services Safewatch Plus Enterpreneur Security Systems
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso ADT Security Services Safewatch Plus Enterpreneur Security Systems.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione ADT Security Services Safewatch Plus Enterpreneur Security Systems, manuali di manutenzione, brevi manuali o manuali utente ADT Security Services Safewatch Plus Enterpreneur Security Systems. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto ADT Security Services Safewatch Plus Enterpreneur Security Systems.

Manuali per l’uso simili

Manuale completo del dispositivo ADT Security Services Safewatch Plus Enterpreneur Security Systems, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare ADT Security Services Safewatch Plus Enterpreneur Security Systems dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti ADT Security Services Safewatch Plus Enterpreneur Security Systems.

Il manuale per l’uso completo ADT Security Services, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale ADT Security Services Safewatch Plus Enterpreneur Security Systems - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice ADT Security Services Safewatch Plus Enterpreneur Security Systems, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per ADT Security Services Safewatch Plus Enterpreneur Security Systems che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo ADT Security Services Safewatch Plus Enterpreneur Security Systems - che ci dovrebbe aiutare nei primi passi durante l'uso ADT Security Services Safewatch Plus Enterpreneur Security Systems
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del ADT Security Services Safewatch Plus Enterpreneur Security Systems
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio ADT Security Services Safewatch Plus Enterpreneur Security Systems in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su ADT Security Services Safewatch Plus Enterpreneur Security Systems?

Utilizza il modulo sottostante

Se non hai risolto il problema con ADT Security Services Safewatch Plus Enterpreneur Security Systems con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con ADT Security Services Safewatch Plus Enterpreneur Security Systems è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)