Italiano dropdown-ico

Manuale per l’uso Honeywell RTH221B1021/A

40 pagine Non applicabile
Scarica

Vai alla pagina of 40

Summary
  • Honeywell RTH221B1021/A - page 1

    RTH2300 /RTH22 1 Pro gr am mab le The rm os tat Quick Inst allation Guid e 69-2448ES-03 ...

  • Honeywell RTH221B1021/A - page 2

    69 -2 448ES— 03 ii Quick In stallation Gui de Identif y S ystem T ype This thermostat is compatible with the following systems: Gas, oil or electric fur nace • Central air conditioner • Hot water system with or without pump • Millivolt system • Central heating and cooling system • Heat pump without auxiliary/backup heat ? ...

  • Honeywell RTH221B1021/A - page 3

    1 69-2448ES—03 RTH2300 /RTH221 1 T urn Of f Power to H eat ing/ Cooling Sy stem M28097 ...

  • Honeywell RTH221B1021/A - page 4

    6 9 -24 4 8 ES— 03 2 Quick In stallation Gui de Remove Old Thermost at 2 M28099 Old thermostat Cover Remove old thermostat but leave wallplate with wires attached. Do not remove wallplate yet MERCUR Y NOTICE Do not put your old therm ostat in the trash if it contain s merc ury in a sealed tube. Contact your local waste management authority for in ...

  • Honeywell RTH221B1021/A - page 5

    3 69-2448ES—03 RTH2300 /RTH221 If any wires are not attached to your old thermostat or are attached to a terminal marked C or C1 , they will not be connected to your new thermostat. Wrap the bare metal end of each of these wires with electrical tape, so it can- not touch and short other wires. Identif y Wires 3 M29988 Disconne ct wires and remove ...

  • Honeywell RTH221B1021/A - page 6

    6 9 -24 4 8 ES— 03 4 Quick In stallation Gui de Mount N ew Wallplat e Loosen the locking screw at the bottom of the 1. thermostat. Note that the screw is captive and cannot be removed from the wallplate. Separate the thermostat from the wallplate as per 2. Figure 1. Position the wallplate against the wall and mark hole 3. positions with a pencil. ...

  • Honeywell RTH221B1021/A - page 7

    5 69-2448ES—03 RTH2300 /RTH221 Connect Wires (typical wiring) Loosen the terminal screws using a screwdriver , insert 2. the wires, then tighten the screws. Push any excess wire back into the wall opening. 3. Labels don’ t match? If a wire does not match any terminal designation, see next page. 5 Match each labeled wire with the terminal having ...

  • Honeywell RTH221B1021/A - page 8

    6 9 -24 4 8 ES— 03 6 Quick In stallation Gui de Connect Wires (alternat e w iring) 5 If labeled wire does not match any terminal design ation, see diagram below. M32169A REMOVE JUMPER BETWEEN R AND RC IF YOU HAVE WIRES ON BOTH R AND RC . DO NOT USE C, C1, OR X WIRE. DO NOT USE B WIRE IF YOU ALREADY HAVE 0 WIRE. WRAP BARE END OF WIRE WITH ELECTRIC ...

  • Honeywell RTH221B1021/A - page 9

    7 69-2448ES—03 RTH2300 /RTH221 Set jumper JP1, on the back of the thermostat, if you have connected a wire to the G terminal. Set He atin g Fan Cont rol 6 HG Leave the jumper in this factory-set position if you have a gas or oil fur nace. HE Place the jumper to this position if you have an electric furnace. Incorrect jumper setting: An incorrect ...

  • Honeywell RTH221B1021/A - page 10

    6 9 -24 4 8 ES— 03 8 Quick In stallation Gui de Set jumper JP2, on the back of the thermostat, if you have a heat pump. Set He at Pump Reversi ng V alve 7 O Leave the jumper in this factory-set position if you have connected O wire to the O/B terminal. B Place the jumper to this position if you have connected B wire to the O/B terminal. Incorrect ...

  • Honeywell RTH221B1021/A - page 11

    9 69-2448ES—03 RTH2300 /RTH221 Install 2 AAA batteries 1. on the back of the thermostat. Install Batteri es and Thermostat 8 Align the two brackets 2. on the top of the thermostat with the corresponding slots on the top of the wallplate. Push the thermostat 3. against the wallplate. Tighten the screw 4. at the bottom of the thermostat. T ur n pow ...

  • Honeywell RTH221B1021/A - page 12

    Advanced Inst allation System setup ...................................................................... 11 T emperature display ...........................................................12 Time display format ...........................................................13 Heating cycles per hour ................................................... ...

  • Honeywell RTH221B1021/A - page 13

    RTH2300 /RTH221 11 69-2448ES—03 About your new thermost at WIRING ASSIST ANCE TROUBLESHOOTING Syste m setu p Follow the procedure below to personalize and con- figure the thermostat according to the heating/cooling system. Press and hold the 1. s and t buttons simultaneously (for three seconds) until the display appears as shown below. Function n ...

  • Honeywell RTH221B1021/A - page 14

    Advanced Insta llatio n Guide 6 9 - 2 4 4 8 E S — 0 3 12 About your new thermost at WIRING ASSIST ANCE TROUBLESHOOTING Press the s or t button to select Fahrenheit or Celsius temperature display . T emperature display 0 Fahrenheit temperature display (°F) 1 Celsius temperature display (°C) When correct setting is selected, press both s and t to ...

  • Honeywell RTH221B1021/A - page 15

    RTH2300 /RTH221 13 69-2448ES—03 About your new thermost at WIRING ASSIST ANCE TROUBLESHOOTING Press the s or t button to select 12-hour display or 24-hour display . Time dis play format 0 12-hour display 1 24-hour display When correct setting is selected, press both s and t to display next function . 2 0 ...

  • Honeywell RTH221B1021/A - page 16

    Advanced Insta llatio n Guide 6 9 - 2 4 4 8 E S — 0 3 14 WIRING ASSIST ANCE TROUBLESHOOTING When correct setting is selected, press both s and t to display next function . Heating cycles per hour Note: Make sure system switch is in the heat position. Press the s or t button to select your heating system and optimize its operation: 5 12 min, Gas o ...

  • Honeywell RTH221B1021/A - page 17

    RTH2300 /RTH221 15 69-2448ES—03 WIRING ASSIST ANCE TROUBLESHOOTING When correct setting is selected, press the s and t buttons to save any changes and exit the menu. Compressor Protection Press the s or t button to select compressor protec- tion: Damage can occur if the compressor is restarted too soon after shutdown. This fea- ture forces the co ...

  • Honeywell RTH221B1021/A - page 18

    Advanced Insta llatio n Guide 6 9 - 24 4 8 E S— 0 3 16 About your new thermost at WIRING ASSIST ANCE TROUBLESHOOTING Customer assistance For assistanc e with this pro duct, please visit http://y ourhome.hone ywell.com or call Honeywell Custom er Care toll-free at 1-800-468-1502. ...

  • Honeywell RTH221B1021/A - page 19

    RTH2300 /RTH221 17 69-2448ES—03 About your new thermost at WIRING ASSIST ANCE TROUBLESHOOTING One -yea r l imite d warra nt y Honeywell warran ts this product, excluding batter y , to be free from defects in the workmanship or materials , under normal use and service, for a period of one (1) year from the date of purchase by the consumer . If at ...

  • Honeywell RTH221B1021/A - page 20

    Automation and Control Solutions Honeywell Inter national Inc. 1985 Douglas Drive North Golden Valley , MN 55422 Honeywell Limited-Honeywell Limitée 35 Dynamic Drive T oronto, Ontario M1V 4Z9 http://yourhome.honeywell.com ® U. S. Re gi ste re d Trad em ar k © 2 010 Ho ne ywe ll Int er na tio na l In c. 69 -2448 ES — 03 M. S. R ev. 10 - 10 Prin ...

  • Honeywell RTH221B1021/A - page 21

    RTH2300 /RTH22 1 T er mos ta to p rog ra ma ble Guía d e instalación rápid a 69-2448ES-03 ...

  • Honeywell RTH221B1021/A - page 22

    69 -2 448ES— 03 ii Guía de insta lación rápida Identifique el tipo de sistema Este termostato es compatible con los siguientes sistemas: Calefactor a gas, aceite o eléctrico • Aire acondicionado central • Sistema a agua caliente con o sin bomba • Sistema de milivoltios • Calefacción y aire acondicionado centrales • B ...

  • Honeywell RTH221B1021/A - page 23

    1 69 -2448ES—03 RTH2300 /RTH221 1 Desc onecte la aliment ación en el sistema de calefacción/refrigeración M28097 ...

  • Honeywell RTH221B1021/A - page 24

    6 9 -24 4 8 ES— 03 2 Guía de insta lación rápida Remueva s u viejo termost ato 2 M28099 T ermostato viejo Cubierta Retir e el termos tato existente pero deje la placa de montaje con los cables adheridos. No retirar la placa mural todavía ADV E RTE NC IA SO BR E E L MERCURIO: N o ar ro je el v ie jo ter mo st ato a l a b as ur a s i co nti en ...

  • Honeywell RTH221B1021/A - page 25

    3 69 -2448ES—03 RTH2300 /RTH221 Identifique los cables 3 Si en el viejo termostato hubiera cables no conectados o conectados a un terminal marcado C o C1, estos cables no se usarán con el nuevo termostato. Recubra el extremo de metal desnudo de cada uno con cinta aisladora para que no puedan tocarse y producir un corto circuito. M29988 Desconec ...

  • Honeywell RTH221B1021/A - page 26

    6 9 -24 4 8 ES— 03 4 Guía de insta lación rápida Instalar la nuev a placa mural 4 Aflojar los tornillos de la base del termostato. El 1. tornillo está cautivo y no se lo puede retirar de la base. Separar el termostato de la placa mural como se 2. indica en la Figura 1. Colocar la placa mural contra la pared y marcar la 3. posición de los agu ...

  • Honeywell RTH221B1021/A - page 27

    5 69 -2448ES—03 RTH2300 /RTH221 Conec te los cabl es (conexión tí pica) 5 Haga coincidir cada cable etiquetado con el terminal 1. de la misma letra. Aflojar los tornillos del terminal con un destor nillador , 2. introducir los cables y reajustar los tornillos. Empuje el exceso de cables en el agujero de la pared. 3. ¿Las etiquetas no coinciden ...

  • Honeywell RTH221B1021/A - page 28

    6 9 -24 4 8 ES— 03 6 Guía de insta lación rápida Conect e los cables (conexión alternati va ) 5 Si un cable etiquetado no coincide con la designación de ningún terminal, refiérase al diagrama siguiente: SI LOS CABLES ESTÁN CONECTADOS CON LOS TERMINALES R Y RC , RETIRE EL PUENTE. NO USAR LOS CABLES C, C1 O X. NO USAR EL CABLE B SI YA EXIST ...

  • Honeywell RTH221B1021/A - page 29

    7 69 -2448ES—03 RTH2300 /RTH221 Ajuste el puente JP1, que está en la parte de atrás del termostato, si se conectó un cable al terminal G. Aju ste el cont rol del vent ilador 6 HG Deje el puente en este ajuste de fábrica en el caso de una estufa a gas o a aceite HE Ponga el puente en esta posición en el caso de una estufa eléctrica. Ajuste i ...

  • Honeywell RTH221B1021/A - page 30

    6 9 -24 4 8 ES— 03 8 Guía de insta lación rápida Ajustar el puente JP2, en la parte de atrás del termostato, en el caso de una bomba de calor . Ajuste de la válvula de inversión 7 O Dejar el puente en este ajuste de fábrica si hay un cable O conectado al terminal O/B. B Poner el puente en esta posición si hay un cable B conectado al termi ...

  • Honeywell RTH221B1021/A - page 31

    9 69 -2448ES—03 RTH2300 /RTH221 Ins talaci ón de las pil as y del termostato 8 Instalar 2 pilas AAA en 1. la parte de atrás del termostato. Alinear las dos lengüetas 2. de la parte superior del termostato con las ranuras correspondientes de la parte superior de la placa mural. Empujar el termostato 3. contra la placa mural. Ajustar el tornillo ...

  • Honeywell RTH221B1021/A - page 32

    Guía de instalación avanzada Cómo cambiar la configuración ........................................11 Visor de la temperatura .....................................................12 Formato de la hora ............................................................. 13 Ciclos de calefacción por hora ..........................................14 Pro ...

  • Honeywell RTH221B1021/A - page 33

    RTH2300 /RTH221 11 69-2448ES—03 About your new thermost at WIRING ASSIST ANCE TROUBLESHOOTING Configuración del sistem a El procedimiento a continuación permite personalizar y configurar el termostato según el sistema de calefacción/enfriamiento. Presionar los botones 1. s y t al mismo tiempo (3 seg.) hasta que se vea lo que se indica en la i ...

  • Honeywell RTH221B1021/A - page 34

    Guía de insta lación avanzada 6 9 - 2 4 4 8 E S — 0 3 12 About your new thermost at WIRING ASSIST ANCE TROUBLESHOOTING Vi sor de la tem per atur a 0 Visualización de la temperatura en Fahrenheit (°F) 1 Visualización de la temperatura en Centígrados (°C) Cuando haya elegid o la configu ración correc ta, presione s y t para mostrar la funci ...

  • Honeywell RTH221B1021/A - page 35

    RTH2300 /RTH221 13 69-2448ES—03 About your new thermost at WIRING ASSIST ANCE TROUBLESHOOTING 2 0 Forma to de la hor a 0 Visualización de la 12 ho ra s 1 Visualización de la 24 ho ra s Cuando haya elegid o la configu ración correc ta, presione s y t para mostrar la función siguiente. Presione los botones s o t p ar a op ta r e ntr e visualiza ...

  • Honeywell RTH221B1021/A - page 36

    Guía de insta lación avanzada 6 9 - 2 4 4 8 E S — 0 3 14 About your new thermost at WIRING ASSIST ANCE TROUBLESHOOTING 3 5 Cuando haya elegid o la configu ración correc ta, presione s y t para mostrar la función siguiente. Ciclos de calefacción por hora No ta: cer cióre se que e l interr uptor del sistema esté en la posición de ca lor . P ...

  • Honeywell RTH221B1021/A - page 37

    RTH2300 /RTH221 15 69-2448ES—03 About your new thermost at WIRING ASSIST ANCE TROUBLESHOOTING 4 1 Cuando haya elegid o la configu ración correc ta, presionar s y t para salvag uardar los cambios y salir del menú. Protección del compresor Presione los botones s o t para seleccionar Protección del compresor: El compresor puede dañarse si se pu ...

  • Honeywell RTH221B1021/A - page 38

    Guía de insta lación avanzada 6 9 - 24 4 8 E S— 0 3 16 About your new thermost at WIRING ASSIST ANCE TROUBLESHOOTING Asistencia al cliente Si necesita asistencia, visite http://yourhome.honeywell.com o llame al número gratuito de atención al cliente de Honeywel l al 1 800 468-1502 . ...

  • Honeywell RTH221B1021/A - page 39

    RTH2300 /RTH221 17 69-2448ES—03 About your new thermost at WIRING ASSIST ANCE TROUBLESHOOTING Ga rant ía limi tad a d e 1 a ño Honeywell garant iza este producto, a excepción de la batería, por el término de un (1) año contra cualquier defecto de fabricaci ón o de los materiale s, a partir de la fecha de compra por parte del consumidor . S ...

  • Honeywell RTH221B1021/A - page 40

    Automatización y control desenlace Honeywell Inter national Inc. 1985 Douglas Drive North Golden Valley , MN 55422 Honeywell Limited-Honeywell Limitée 35, Dynamic Drive T oronto, Ontario M1V 4Z9 http://yourhome.honeywell.com ® Marca Registrada en lo s EE. UU. © 2010 Hon eywe ll Int erna tion al In c. 69 -2448 ES — 03 M. S. R ev. 10 - 10 Im pr ...

Fabbricante Honeywell Categoria Thermostats

I documenti che otteniamo dal fabbricante del dispositivoHoneywell RTH221B1021/A possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Honeywell
- manuali per l’uso RTH221B1021/A
- schede prodotto Honeywell
- opuscoli
- o etichette energetiche Honeywell RTH221B1021/A
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Honeywell RTH221B1021/A.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Honeywell RTH221B1021/A, manuali di manutenzione, brevi manuali o manuali utente Honeywell RTH221B1021/A. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Honeywell RTH221B1021/A.

Manuali per l’uso simili

Manuale completo del dispositivo Honeywell RTH221B1021/A, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Honeywell RTH221B1021/A dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Honeywell RTH221B1021/A.

Il manuale per l’uso completo Honeywell, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Honeywell RTH221B1021/A - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Honeywell RTH221B1021/A, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Honeywell RTH221B1021/A che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Honeywell RTH221B1021/A - che ci dovrebbe aiutare nei primi passi durante l'uso Honeywell RTH221B1021/A
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Honeywell RTH221B1021/A
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Honeywell RTH221B1021/A in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Honeywell RTH221B1021/A?

Utilizza il modulo sottostante

Se non hai risolto il problema con Honeywell RTH221B1021/A con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Honeywell RTH221B1021/A è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)