Italiano dropdown-ico

Manuale per l’uso Hobart HFC50 ML-135555

28 pagine 0.93 mb
Scarica

Vai alla pagina of 28

Summary
  • Hobart HFC50 ML-135555 - page 1

    MODEL HFD/HFC SERIES ELECTRIC FRYERS MODELS HFD50 ML-135551 HFD85 ML-135553 HFC50 ML-135555 HFC85 ML-135558 HFO15 ML-135558 HFO21 ML-135559 FORM 35612 (08-03) 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 ...

  • Hobart HFC50 ML-135555 - page 2

    — 2 — TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Unpacking ...

  • Hobart HFC50 ML-135555 - page 3

    — 3 — Installation, Operation and Care of MODEL HFD/HFC SERIES ELECTRIC FRYERS SAVE THESE INSTRUCTIONS FOR FUTURE USE GENERAL Hobart HFD/HFC Series Electric Fryers are available in 2 sizes with an array of features and options for a range of commercial fryer applications. Width Fry Compound Model KW Inches / cm Lb / kg HFD/HFC50 17 15 1 / 2 / 3 ...

  • Hobart HFC50 ML-135555 - page 4

    — 4 — HF Series Fryer — Construction Features Model Filter Ready Battery Battery Configuration Interplumbing HFD50/HFC50 Opt. (Use HMF50) Opt. Opt. HFD85/HFC85 Opt. (Use HMF85) Opt. Opt. Model Fat Melt Thermostat Basket Lift(s) Basket(s) Cycle Twin Single Tri HFD50 Std. Solid State Opt. Std. Opt. N/A HFD85 Digital Display Std. Opt. Opt. HFC50 ...

  • Hobart HFC50 ML-135555 - page 5

    — 5 — HFO Series Frymate — Finish Options Model HFO15, HFO21 Front Door Legs Standard Stainless Steel Stainless Steel Legs Optional Not Applicable Casters * Model HFO15 is for use with the HF50 Series Fryers. Model HFO21 is for use with the HF85 Series Fryers. HFO Series Frymate — Features Tops Heat Lamp Drain Solid Pan Solid Pan Perforated ...

  • Hobart HFC50 ML-135555 - page 6

    — 6 — INSTALLATION Before installing the fryer, verify that the electrical service agrees with the specifications on the fryer data plate which is located on the inside of the door panel. If the supply and equipment requirements do not agree, do not proceed with the installation. Contact your dealer or Hobart Corporation immediately. UNPACKING ...

  • Hobart HFC50 ML-135555 - page 7

    — 7 — Fig. 1 LEVELING Place a carpenter's level on top of the fryer and level the fryer front-to-back and side-to-side by turning the adjustable legs or casters. ELECTRICAL CONNECTIONS WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL CODES. WARNING: DISCONNECT THE ELECTRICAL POW ...

  • Hobart HFC50 ML-135555 - page 8

    — 8 — OPERATION WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING AND SERVICING THE FRYER. WARNING: SPILLING HOT FRYING COMPOUND CAN CAUSE SEVERE BURNS. DO NOT MOVE FRYER WITHOUT DRAINING ALL FRYING COMPOUND FROM THE TANK. BEFORE FIRST USE Clean the Fryer and Heating Elements Do not operate fryer without frying compo ...

  • Hobart HFC50 ML-135555 - page 9

    — 9 — ADDING SOLID SHORTENING If replacing shortening, place the block of shortening in the room with the fryer for 1 to 2 hours before using. This will soften the shortening and make it easier to divide. CAUTION: Failure to remove crumb screens prior to addition of fresh shortening may cause heating elements to overheat, allowing shortening to ...

  • Hobart HFC50 ML-135555 - page 10

    — 10 — CONTROLS — Control Guide HFD SERIES (MANUFACTURED AFTER AUGUST 2003 WITH TDI CONTROLLERS) — Power switch; for turning the fryer on or off. — For cleaning purposes when the fryer is filled with water. Temperature is maintained at approxmiately 192°F (89°C).** — For entering and exiting the program mode. For scrolling through pro ...

  • Hobart HFC50 ML-135555 - page 11

    — 11 — PARAM ETER SELECT DISPLAY SCROLL Left Timer P re ss or to en ter ti me . LED is lit above the left ba sket icon . The ti me val ue is di splay ed in window. Pr es s a nd scroll to next item . Right Timer Pr es s o r to en te r t i me . LED is lit ab ove the right bas k et icon . The ti me val ue is di splay ed in window. Pr es s a nd scr ...

  • Hobart HFC50 ML-135555 - page 12

    — 12 — Melt Options (HFD Series) When using solid shortening in the fryer, the CY S (solid shortening) option must be used. Solid shortening must be gently warmed to a liquid state before heating to frying temperatures. Melting solid shortening without using this option will damage the fry tank and scorch the shortening. The controller has thre ...

  • Hobart HFC50 ML-135555 - page 13

    — 13 — USING THE FRYER (After Startup) Models Without Basket Lift Option 1. Load the fry basket(s); do not overfill. 2. Carefully lower basket(s) into shortening. 3. Press to start the left timer. Press to start the right timer. 4. When the timer times out, a beeper sounds. Press to silence the left timer beeper. Press to silence the right time ...

  • Hobart HFC50 ML-135555 - page 14

    — 14 — Control Guide CONTROLS — HFC SERIES (MANUFACTURED AFTER AUGUST 2003 WITH TDI CONTROLLERS) — Power switch; for turning the fryer on or off. — For setting fry temperature. For viewing shortening temperature and set temperature. — For entering and exiting the program mode. — For selecting program parameters. For setting timers 1 t ...

  • Hobart HFC50 ML-135555 - page 15

    — 15 — PARAMETER STEPS LEFT DISPLAY RIGHT DISPLAY Press SELECT OPTIONS Press DEGREES F or C F or C Press to select Fahrenheit or Celsius. DEGREES F or C F or C Press when complete. PROGRAM Press SELECT OPTIONS Press SET PASS NEW PASS Press to select NO PASS. NO PASS NEW PASS Press when complete. PROGRAM Press SELECT OPTIONS Press SET PASS NEW P ...

  • Hobart HFC50 ML-135555 - page 16

    — 16 — PARAMETER STEPS LEFT DISPLAY RIGHT DISPLAY Press SELECT OPTIONS Press ENGLISH (Factory Default) LANGUAGE Press to select a language. ENGLISH/ESPANOL FRANCAIS/DEUTSCH HOLLAND Press when complete. PROGRAM Press SELECT OPTIONS Press NO MELT/LIQUID/SOLID Press to select melt options. NO MELT/LIQUID/SOLID Press when complete. PROGRAM Press SE ...

  • Hobart HFC50 ML-135555 - page 17

    — 17 — Melt Options (HFC Series) When using solid shortening in the fryer, the SOLID melt option must be used. Solid shortening must be gently warmed to a liquid state before heating to frying temperatures. Melting solid shortening without using this option will damage the heating elements and scorch the shortening. The controller has three opt ...

  • Hobart HFC50 ML-135555 - page 18

    — 18 — TEMPERATURE AND TIME PROGRAMMING Temperature 1. Press to enter program mode. PROGRAM is displayed in the window. 2. Press to enter temperature mode. 000°F and TEMP are displayed in the window. 3. Press through to enter desired fry temperature. The fry temperature is displayed in the window. 4. Press to exit the temperature mode. Press a ...

  • Hobart HFC50 ML-135555 - page 19

    — 19 — Setting Advanced Time Features 1. Press and enter the program mode. 2. Press for timers through , or press for timers through . The LEDs are lit on the timers available for programming, and SELECT PRODUCT is displayed in the window. 3. Select a timer; the programmed time is displayed in the window. A. Duty Time : 1) Press either arrow on ...

  • Hobart HFC50 ML-135555 - page 20

    — 20 — USING THE FRYER (After Startup) Models Without Basket Lift Option 1. Load the fry basket(s), do not overfill. 2. Carefully lower basket(s) into shortening. 3. Press the desired number to select the product to be timed. Timers through are programmed for products. Once the product is selected, select or button to start timing of the produc ...

  • Hobart HFC50 ML-135555 - page 21

    — 21 — FRYING (All Models) Heat shortening to set temperature. Pieces of product to be fried should be about the same size to ensure the same doneness. Drain or wipe dry raw or wet foods to minimize splatter when lowering into the hot oil. Do not overfill baskets. Recommended maximum capacities are: Lb / kg of Total Lb / kg Total Lb / kg Produc ...

  • Hobart HFC50 ML-135555 - page 22

    — 22 — DAILY FILTERING Fryers Without Filter Ready Options Turn power switch off when draining or filling. Always filter the shortening while liquified. A cold fryer will not drain properly because the shortening under the cold zone tube area will remain hard, even if the heat is on for a few minutes. If necessary, the clean-out rod may be used ...

  • Hobart HFC50 ML-135555 - page 23

    — 23 — CLEANING (All Models) WARNING: DISCONNECT THE ELECTRICAL POWER SUPPLY TO THE MACHINE AND FOLLOW LOCKOUT/TAGOUT PROCEDURES. Daily Clean the exterior of your fryer regularly with a damp cloth and polish with a soft dry cloth. If regular cleaning is neglected, grease will be burned on and discolorations may form. These may be removed by was ...

  • Hobart HFC50 ML-135555 - page 24

    — 24 — CLEANING (CONTINUED) Weekly or as Required 1. Once the shortening has been drained, flush out scraps and sediment with a small amount of warm shortening. Allow the tank to drain thoroughly. 2. Close the drain valve and fill the tank with a non-corrosive, grease-dissolving commercial cleaner, following the manufacturer's instructions ...

  • Hobart HFC50 ML-135555 - page 25

    — 25 — TROUBLESHOOTING ALARMS AND ERROR MESSAGES O pen Probe - If an open probe is detected, the heat demand is disabled and any running cooking cycles are cancelled. All operator buttons are disabled. The control displays the following message: HFD Models - Prob HFC Models - OPEN PROBE The alarm sounds continuously until the fault clears or th ...

  • Hobart HFC50 ML-135555 - page 26

    — 26 — MAINTENANCE WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING AND SERVICING THE FRYER. WARNING: SPILLING HOT FRYING COMPOUND CAN CAUSE SEVERE BURNS. DO NOT MOVE FRYER WITHOUT DRAINING ALL FRYING COMPOUND FROM THE TANK. LUBRICATION Motors used on basketlifts are permanently lubricated. SERVICE AND PARTS INFORMA ...

  • Hobart HFC50 ML-135555 - page 27

    — 27 — NOTES ...

  • Hobart HFC50 ML-135555 - page 28

    — 28 — FORM 35612 (08-03) PRINTED IN U.S.A. NOTES ...

Fabbricante Hobart Categoria Fryer

I documenti che otteniamo dal fabbricante del dispositivoHobart HFC50 ML-135555 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Hobart
- manuali per l’uso HFC50 ML-135555
- schede prodotto Hobart
- opuscoli
- o etichette energetiche Hobart HFC50 ML-135555
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Hobart HFC50 ML-135555.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Hobart HFC50 ML-135555, manuali di manutenzione, brevi manuali o manuali utente Hobart HFC50 ML-135555. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Hobart HFC50 ML-135555.

Manuali per l’uso simili

Manuale completo del dispositivo Hobart HFC50 ML-135555, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Hobart HFC50 ML-135555 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Hobart HFC50 ML-135555.

Il manuale per l’uso completo Hobart, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Hobart HFC50 ML-135555 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Hobart HFC50 ML-135555, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Hobart HFC50 ML-135555 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Hobart HFC50 ML-135555 - che ci dovrebbe aiutare nei primi passi durante l'uso Hobart HFC50 ML-135555
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Hobart HFC50 ML-135555
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Hobart HFC50 ML-135555 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Hobart HFC50 ML-135555?

Utilizza il modulo sottostante

Se non hai risolto il problema con Hobart HFC50 ML-135555 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Hobart HFC50 ML-135555 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)