Italiano dropdown-ico

Manuale per l’uso Generac Power Systems K4080

24 pagine 4.22 mb
Scarica

Vai alla pagina of 24

Summary
  • Generac Power Systems K4080 - page 1

    OPERA T OR’S MANUAL PLEASE READ THIS MANUAL CAREFULL Y AND KEEP READY A T ALL TIMES KUBOT A ® BR USH MO WER MODEL K4080 ...

  • Generac Power Systems K4080 - page 2

    BEFORE OPERA TION ——————————————————————— 1 SAFE OPERA TION —-——————————————————————— 2-3 A TT ACHING T O THE EXCA V A T OR —-———————————————— 4-5 ADJUSTMENT & MAINTE NANCE ———————— ——————? ...

  • Generac Power Systems K4080 - page 3

    BEFORE OPERA TION 1 BEFORE OPERA TION 1. Keep children out of the operating area under the watchful eye of another re- sponsible adult. 2. Never allow another person in the operator’s station of the excavator while the machine is in operation. 3. Stop machine operation if a person approaches the mowing area. 4. The operator should walk through th ...

  • Generac Power Systems K4080 - page 4

    SAFE OPERA TION 2 SAFETY Failure to heed these warnings may re sult in personal injury or death. • Before operating this machinery r ead the owner’s manual carefully. • Use OSHA approved eye, ear and head protection to protect the operator from any flying debris and noise. • All personnel except operator should be 150 f eet clear of machi n ...

  • Generac Power Systems K4080 - page 5

    SAFE OPERA TION 3 • Stop the operation of this machine when pe ople or vehicle driver’s vision bec omes obscured, caused by the discharge of material s and dust. Also avoid operating this attachment in unusually foggy or dusty conditions or at night. • Never leave the excavator or the brush shredding attachment unattended while it is in the l ...

  • Generac Power Systems K4080 - page 6

    AT TA C H I N G T O T H E E X C AVAT O R • Be sure to inspect all safety devices (inc luding safety shields, guards, deflectors, etc.) before each use. Safety Device Examples Shaft protection cap Motor & gearbox cover Debris chain curtain guarding • Maintain all safety decals and make sure they are visible to the operator and by- standers. ...

  • Generac Power Systems K4080 - page 7

    A TT ACHING T O THE KX080 AT T E N T I O N The K4080 brush mower is designed speci fically for the Kubota KX080 excavator and should not be used on any other machin e. Ma ke sure the person who is attach- ing this brush mower has knowledge of a ttaching regular buckets and can do so in a safe manner. The method used most ofte n for attaching this b ...

  • Generac Power Systems K4080 - page 8

    ADJUSTMENT & MAINTENANCE CLEANING YOUR BRUSH MOWER To preserve life of paint and decals, wash the brush mower after each use. The preservation of your brush mower’s decals is essential to safet y, so make sure they are kept in good condition. It is also reco mmended that some sort of degreasing solution be used on all bearings. ADJUSTMENT &am ...

  • Generac Power Systems K4080 - page 9

    Running Your Attachment The K4080 brush mower is designed to cut all types of vegetation such as grass, brush and small trees. The condition of your terr ain and the material to be cut should be evaluated for the best results. House Rotation Mowing Brush on flat terrain can be cut by rotating the house control from side-to-si de and keeping the cut ...

  • Generac Power Systems K4080 - page 10

    BASIC OPERA TION BASIC OPERA TION 8 1. Before beginning your job, walk the mowing area and clear all hidden hazards such as large rocks, stumps, utility lines and hi dden debris like broken glass, bottles and miscellaneous materials. Pr ojected debris can cause inju ries to operators, pedes- trians, livestock and property. 2. While inspecting your ...

  • Generac Power Systems K4080 - page 11

    BASIC OPERA TION Starting Procedure 1. While the excavator’s engine is turned OFF, and all moving parts have completely stopped, remove outer spindle cover. 2. Check to see that the br ush mower is in the down posi tion and blades are not touch- ing the ground. Star t the engine and set throttle at idle speed. Important: Do not start the operatin ...

  • Generac Power Systems K4080 - page 12

    MAINTENANCE MAINTENANCE 10 AT T E N T I O N Before doing any service work, ob serve the following safety rules: 1. Remove the ignition key from the operating vehicle and allow all movements to stop before leaving the operator’s position and starting any maintenance activities. 2. Allow all movements to st op before leaving the operator’s positi ...

  • Generac Power Systems K4080 - page 13

    REPLACING KNIVES REPLACING KNIVES 1 1 1. Worn knives, bolts, and spacers must be replaced. Neglecting the replacement of these parts could cause the cutti ng drum to run out of balance. Do not mix new parts with older, worn parts. Alw ays replace wear washer s w hen blades are replaced. Failing to do so could cause the cutter drum to run out of bal ...

  • Generac Power Systems K4080 - page 14

    HYDRAULIC DIAGRAM HYDRAULIC DIAGRAM 12 The diagram below represent s the hydraulic plumbing sy stem for the Kubot a K4080 Brush Mower att achment. T o reverse cutter drum rot ation, reverse the hoses on the motor side of the protection valve. On quick couplers, the female end is usually the pressure in. Double check the excavator plumbing to insure ...

  • Generac Power Systems K4080 - page 15

    TRANSPORT TRANSPOR T 13 ATTENTION Allow all movements to stop bef ore leaving the operator’s posit ion to lubricate or clean the machine. Before working on or underneat h the brush mower, place blocks on both sides of the operating vehicle tires or treads and under each end of the mower to pre- vent accidental lowering of the machine. Remove the ...

  • Generac Power Systems K4080 - page 16

    T. Where is the serial number for my machine? C. The serial number for your brush shredder is stamped next to th e mounting bracket on the opposite side of the motor. T. Where do I find replacement parts? C. Your local Kubota dealer. T. How often should I change my knives? C. Replacing the cutting knives is a performa nce issue. When the cut begins ...

  • Generac Power Systems K4080 - page 17

    T. How do I reverse the cutter drum rotation? C. Refer to the Adjustments and Maintenance section of this manual for information on reversing the hydraulic hoses at the moto r to reverse the cutte r drum direction. T. How do I replace my knives? C. Refer to the Adjustments and Maintenance section of this manual for information regarding the replace ...

  • Generac Power Systems K4080 - page 18

    K4080 Brush Mower S pecifications SPECIFICA TIONS SPECIF ICA TIONS 16 W orking Width 40” (101.6 cm) Overall Width 58” (127 cm) W eight 1,325 lbs. (600 kg) Number of knives 24/12 –77 lbs.(35 kg) Capacity 6“. (15.3cm.) Hyd. Flow required 23 gpm / 87 lpm FEA TURES • Bolt on excavator bucket st yle quick att ach mount • 3/4” & 3/8” ...

  • Generac Power Systems K4080 - page 19

    KNIFE ASSEMBL Y # Description Model Part # Quantity 1 2 3 4 5 6 7 BOLT, KNIFE 1"x4" GR8 -2 1/2" Shoulder KNIFE, SHREDDER SPACER, 1" Flat Washer (KNIFE BOLT) NUT, CASTLE 1" (KNIFE) PIN, ROLL 3/16"x1 1/2" (KNIFE BOLT) KNIFE, SHREDDER (CENTER) WASHER, LOCK 1" (KNIFE BOLT) All All All All All All All 77700-00862 ...

  • Generac Power Systems K4080 - page 20

    DRIVE ASSEMBL Y # Description Model Part # Quantity 1 2 3 4 5 6 7 8 9 10 11 12 GUARD, WIRE - DRIVE SIDE SEAL, SHAFT 3 1/2"x2 3/4" OD WASHER, DAMPENER HOUSING, SPINDLE BREATHER BEARING, BALL 50mm ANGULAR CONTACT NUT, LOCK (DRIVESHAFT) O RING, SPINDLE HOUSING 5/32"x17" MOTOR, HYD 26 gpm flow GUARD, WIRE - IDLER SIDE BEARING, FLANG ...

  • Generac Power Systems K4080 - page 21

    HYDRAULIC PLUMBING # Description Model Part # Quantity 1 2 2a 2b 3 4 5 6 7 Hydraulic Motor-24 GPM Motor Protection Valve MPV Pressure Relief MPV Check Valve Adapter, 12 MORB x 12 MJIC 90 Coupler, 3/4" FEM FLUSH FACE Coupler, 3/4" MALE FLUSH FACE Hose, 44 " 12FJIC x 12 FJIC Breather K4080 K4080 K4080 K4080 K4080 K4080 K4080 K4080 K408 ...

  • Generac Power Systems K4080 - page 22

    NOTES Notes 20 ...

  • Generac Power Systems K4080 - page 23

    K4080 Complete Parts List Qty. Per Unit Description Part Number 1 BEARING, FLANGE (1 15/16" 4 BOLT) 77700-00852 24 KNIFE, SHREDDER 77700-00853 12 KNIFE, SHREDDER (CENTER) 77700-00854 1 O RING, SPINDLE HOUSING 5/32"x17" 77700-00855 2 BEARING, BALL 50mm ANGULAR CON- TACT 77700-00856 1 SEAL, SHAFT 3 1/2"x2 3/4" OD 77700-00857 ...

  • Generac Power Systems K4080 - page 24

    PRINTED IN USA KUBOTA TRACTOR C ORPORATION 3401 Del Amo Blvd., Torrance, CA 90503, U.S.A. Telephone: (310) 370-3370 Western Division: 1175 S. Guild Ave., Lodi, CA 95240 Telephone: (209) 334-9910 Central Division: 14855 FAA Blvd., Forth Worth, TX 76155 Telephone: (817) 571-0900 Northern Division: 6300 at One Kubota Way, Groveport, OH 43125 Telephone ...

Fabbricante Generac Power Systems Categoria Lawn Mower

I documenti che otteniamo dal fabbricante del dispositivoGenerac Power Systems K4080 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Generac Power Systems
- manuali per l’uso K4080
- schede prodotto Generac Power Systems
- opuscoli
- o etichette energetiche Generac Power Systems K4080
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Generac Power Systems K4080.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Generac Power Systems K4080, manuali di manutenzione, brevi manuali o manuali utente Generac Power Systems K4080. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Generac Power Systems K4080.

Manuali per l’uso simili

Manuale completo del dispositivo Generac Power Systems K4080, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Generac Power Systems K4080 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Generac Power Systems K4080.

Il manuale per l’uso completo Generac Power Systems, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Generac Power Systems K4080 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Generac Power Systems K4080, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Generac Power Systems K4080 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Generac Power Systems K4080 - che ci dovrebbe aiutare nei primi passi durante l'uso Generac Power Systems K4080
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Generac Power Systems K4080
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Generac Power Systems K4080 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Generac Power Systems K4080?

Utilizza il modulo sottostante

Se non hai risolto il problema con Generac Power Systems K4080 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Generac Power Systems K4080 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)