-
Garmin SL40 - page 1
...
-
Garmin SL40 - page 2
No part of this document may be reproduced in any form or by any means without the express written consent of Garmin AT, Inc. II Morrow, Garmin AT, and Apollo are trademarks of Garmin AT, Inc. © 2003 by Garmin AT, Inc. All rights reserved. Printed in the U.S.A. Garmin AT, Inc. 2345 Turner Road S.E. Salem, OR 97302 U.S.A. Toll Free 800.525.6726 Can ...
-
Garmin SL40 - page 3
Welcome ... Welcome to a new era of aviation communication. Once again, Garmin AT, Inc. has set new standards in features and ease of use for the general aviation public. The Apollo SL40 is a VHF Communications Transceiver for use by the aviation pilot. Packaged in a new slim form factor that helps you get the most out of limited panel real estate ...
-
Garmin SL40 - page 4
History of Revisions December 1996 Original Release March 1997 Rev. -01 June 1998 Rev. -02 September 2003 Rev. -02a Ordering Information To receive additional copies of the Apollo SL40 User’s Guide, order part #560-0954-02a. The Apollo SL40 Installation Guide is part #560-0956-xx. ii ...
-
Garmin SL40 - page 5
Table of Contents Welcome ... ·······················i History of Revisions ··················i i Ordering Information ·················i i Introduction ······················1 Display ·······················1 Annunciators ············ ...
-
Garmin SL40 - page 6
Intercom Function ·················9 Stuck Mic ·····················9 System Functions ···················1 0 Software Version ·················1 0 RF Level ·····················1 1 Noise Level ····················1 1 Headphone Level ? ...
-
Garmin SL40 - page 7
Introduction This guide describes the operation of the Apollo SL40 VHF Communication Transceiver. Display The 1-line by 16-character display is composed of 5x7 dot matrix alphanumeric high intensity LEDs. A photocell is located in the top left corner of the front panel display. The photocell automatically controls the intensity of the display from ...
-
Garmin SL40 - page 8
Controls Power/Volume/Squelch The knob on the left side of the SL40 controls power on/off, volume, and squelch test. Rotate the knob clockwise (CW) past the detent to turn the power on. Continuing to rotate the knob to the right increases speaker and headphone amplifier volume level. Rotate the knob to the left to reduce the volume level. Pull the ...
-
Garmin SL40 - page 9
Basic Operation This section introduces the basic operating details of the Apollo SL40 VHF Communications Transceiver. Power On/Off Turn the Power/Volume control clockwise past the OFF detent. The SL40 may be installed to be powered from the avionics panel so the on/off control will be disabled. Volume Turn the Power/Volume control clockwise to inc ...
-
Garmin SL40 - page 10
Frequency Monitoring The Frequency Monitoring function allows you to listen to the Standby frequency, while monitoring the Active frequency for activity. Press the MON button to listen to the standby frequency. A small “m” is displayed in front of the Standby frequency. When the Active frequency receives a signal, the unit will switch automatic ...
-
Garmin SL40 - page 11
TWR - Tower frequency GND - Ground frequency ATS - ATIS frequency ATF - Air Traffic Frequency APP - Approach ARR - Arrival AWS - Automatic Weather Station CLR - Clearance/Delivery CTF - Common Traffic Advisory Frequency DEP - Departure frequency FSS - Flight Service Station RFS - Remote Flight Service Station UNI - Unicom frequency MF - Mandatory F ...
-
Garmin SL40 - page 12
Weather (WTH) The standard weather channels are stored in the memory of the SL40. You cannot transmit on a weather channel frequency. A small “x” to the right of the Active frequency indicates that transmitting is not permitted. Press RCL and then turn the Large , outer knob to display the weather (WTH) channel memory. Then, turn the Small , in ...
-
Garmin SL40 - page 13
Removing a Frequency from User Memory You may edit the contents of User memory to remove its stored frequencies when you want to make a change or you receive a “MEM Full” message. 1. Press RCL . Turn the Large knob to the User (MEM) frequencies. 2. Press MEM . Turn Large knob to show “Remove.” 3. Turn the Small knob to choose the frequency ...
-
Garmin SL40 - page 14
Assigning an ID to a User Frequency Frequencies in User (MEM) memory can be given an alphanumeric identifier for your ease of use. 1. Press RCL . Turn the Large knob to the User (MEM) frequencies. 2. Press MEM and hold it for about two seconds. “Assign ID” and the frequency to be given an ID will be displayed. 3. Turn the Small knob to select t ...
-
Garmin SL40 - page 15
Intercom Function When two headphone and microphone jacks are connected to the SL40, these headsets can be used as a voice-activated intercom. When you select the Intercom function with the installed selector switch, the intercom function is enabled. The Volume control will control the headphone listening level. The receive function will automatica ...
-
Garmin SL40 - page 16
System Functions The SL40 includes a number of System Functions that give you more information about your communication equipment. Press and hold the MON button for about three seconds to reach the System Function. Turn the Large, outer knob to display the available functions. Adjustments are made with the Small , inner knob. Software Version The S ...
-
Garmin SL40 - page 17
RF Level The RF Level function shows the relative signal strength of the frequency you are listening to. The range displayed is between 0 and 255. The value will constantly change as you are viewing it as signal conditions change. Noise Level The Noise Level function shows the relative received noise level of the frequency you are listening to. The ...
-
Garmin SL40 - page 18
Mic Squelch 1 and 2 The input level required to break squelch by the microphone is set from this page. Lower numbers indicate a higher input level necessary to break squelch. Turn the Small knob to change the value. The range is from 0 to 127. Transmit Mic The Transmit Microphone page allows you to control which microphone is permitted to transmit. ...
-
Garmin SL40 - page 19
Sidetone Level This function displays and adjusts the sidetone audio level. Turn the Small knob to change the value. The range is from 0 to 255. Setting the value to 0 slaves the sidetone level to the volume control knob. Display Brightness As it arrives from the factory, the SL40 automatically adjusts its display brightness for the current lightin ...
-
Garmin SL40 - page 20
SL40 Specifications Features 760 Communication Channels Frequency Range: 118 to 136.975 MHz Active and Standby Flip/Flop Frequencies Volume Control 16-Character High-Intensity Alphanumeric LED Display Automatic Display Intensity Control Backlit Keypad Controls Transmit Status Indicator 2x8 Frequency Memory and Recall Stores/Recalls Eight User-Defin ...
-
Garmin SL40 - page 21
Physical 1.3” (H) x 6.25” (W) x 10.5” (D) Weight: 2 lbs 15 SL40 Specifications ...
-
Garmin SL40 - page 22
Notes 16 SL40 Specifications ...
-
Garmin SL40 - page 23
...
-
Garmin SL40 - page 24
© 2003 by Garmin AT, Inc. 2345 Turner Rd., S.E. Salem, OR 97302 U.S.A. Phone 503.581.8101 800.525.6726 In Canada 800.654.3415 FAX 503.364.2138 http://www.garminat.com Part #560-0954-02 Rev A September 2003 ...
Hai una domanda su Garmin SL40?
Utilizza il modulo sottostante
Se non hai risolto il problema con Garmin SL40 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Garmin SL40 è probabile che voglia condividere il modo di risolverlo.