-
Husqvarna RZ3019BF - page 1
Operator Manual RZ3019BF / 966582101 Please read the operator’ s manual car efully and mak e sur e y ou understand the instructions befor e using the machine. ...
-
Husqvarna RZ3019BF - page 2
©2010 HTC All rights reserved. Beatrice, NE. Printed in U.S.A. In order to implement improvements, specications and designs can be altered without prior notication. Note that no legal demands can be placed based on the information contained in these instructions. Use only original parts for repairs. The use of other parts voids the warranty ...
-
Husqvarna RZ3019BF - page 3
...
-
Husqvarna RZ3019BF - page 4
W ARNING! Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower . Each person operating the mower must be of sound mind and body and must not be under the in ...
-
Husqvarna RZ3019BF - page 5
5 Congratulations Thank you for purchasing a Husqvarna ride-on mower . This machine is built for superior efciency to rapidly mow primarily large areas. A contr ol panel easily accessible to the operator and a hydrostatic transmission regulated by steering contr ols both contribute to the machine’s perfor m ...
-
Husqvarna RZ3019BF - page 6
6 Good Service Husqvarna’s products are sold only in specialized retail stor es with complete service. This ensures that you as a customer receive only the best support and service. Before the pr oduct is delivered, the machine has, for example, been inspected and adjusted by your retailer . See the certica ...
-
Husqvarna RZ3019BF - page 7
7 R N IMPORT ANT INFORMA TION Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx. These symbols are found on the machine and in the operator’s manual. Study them carefully so that you know what they mean. Reverse Neutral Fast Slow Choke Fuel W arning! Parking Brake CE ...
-
Husqvarna RZ3019BF - page 8
8 Read Shut off engine and Keep a safe Use on slopes No passengers Operator’s remove key befor e distance from no greater Manual perfor ming any the machine than 10° maintenance or repair work Whole body Severing of ngers Do not open or Careful backing up, Careful going exposure to and t ...
-
Husqvarna RZ3019BF - page 9
9 Safety Instructions These instructions are for your safety . Read them carefully . General Operation Read, understand, and follow all instructions on • the machine and in the manual before starting. Do not put hands or feet near rotating parts or • under the machine. Keep clear of the discharge opening at all times. Only al ...
-
Husqvarna RZ3019BF - page 10
10 Operate machine only in daylight or good articial • light. Do not operate the machine while under the • inuence of alcohol or drugs. W atch for trafc when operating near or crossing • roadways. Use extra care when loading or unloading the • machine into a trailer or truck. Always wear eye protection when opera ...
-
Husqvarna RZ3019BF - page 11
11 Personal Safety Equipment Make sure that you have rst aid equipment close • at hand when using the machine. Never use the machine when barefoot. • Always wear protective shoes or boots, pr eferably • with steel toe caps. Always wear approved pr otective glasses or a full • visor when assembling or driving. Always we ...
-
Husqvarna RZ3019BF - page 12
12 8011-517 Ne ver allo w children to operate the machine 8011-518 K eep children awa y from work area Children T ragic accidents can occur if the operator is not alert to the presence of children. Childr en are often attracted to the machine and the mowing activity . Ne v er assume that children will r emain out of the path of d ...
-
Husqvarna RZ3019BF - page 13
13 8011-516 Ne ver fill the fuel tank indoors Safe Handling of Gasoline T o avoid personal injury or property damage, use extreme car e in handling gasoline. Gasoline is extremely ammable and the vapors ar e explosive. Extinguish all cigarettes, cigars, pipes, and other • sources of ignition. Use only approved gasoline cont ...
-
Husqvarna RZ3019BF - page 14
14 8011-515 Ne ver driv e the machine in an enclosed space General Maintenance Never operate machine in a closed area. • Keep all nuts and bolts tight to be sure the • equipment is in safe working condition. Never tamper with safety devices. Check their • proper operation r egularly . Keep machine free of grass, leaves, or ...
-
Husqvarna RZ3019BF - page 15
15 Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, re or eye injury . Sparking in this circuit can not occur after the chassis cable (normally negative, black) is removed from the battery . Use protective goggles. • Ensure that the fuel ller c ...
-
Husqvarna RZ3019BF - page 16
16 IMPORT ANT INFORMA TION The parking brake is not sufcient to lock the machine in place during transport. Ensure that the machine is well fastened to the transport vehicle. Always reverse the machine onto the transport vehicle to avoid tipping it over . W ARNING! Escaping hydraulic oil under pressure can have sufcient for ...
-
Husqvarna RZ3019BF - page 17
17 This operator’s manual describes the Husqvarna Zero T ur n Rider . The rider is tted with a Briggs & Stratton four -stroke overhead valve engine. Control Locations T ransmission from the engine is made via belt-driven hydraulic pumps. Using the left and right steering controls ...
-
Husqvarna RZ3019BF - page 18
18 8050-003 Steering controls Steering Control Levers The machine’s speed and direction ar e continuously variable using the two steering controls. The steering controls can be moved forwar d or backward about a neutral position. Further more, ther e is a neutral position, which is locked if the steering controls ar e mov ...
-
Husqvarna RZ3019BF - page 19
19 Throttle Control The throttle contr ol regulates the engine speed and thereby the rate of r otation of the blades. In order to incr ease or decrease the engine speed, the control is moved forwar d or back respectively . Avoid idling the engine for long periods, as ther e is a risk of fouling the spark plugs. USE FULL THR ...
-
Husqvarna RZ3019BF - page 20
20 Choke Control The choke control is used for cold starts in order to provide the engine with a richer fuel mixtur e. For cold starts the throttle should be pushed fully forward to the choke position. Fuel T ank Read the safety instructions before r efueling. The machine has one fuel tank, just behind the seat. The tank vo ...
-
Husqvarna RZ3019BF - page 21
21 Fuel Shut Off V alve The fuel shut off valve is located in the fuel line under the seat. Tilt seat forward for access. The fuel valve is ON when the valve is parallel to the fuel line. Rotate the valve ¼ turn clockwise to tur n fuel OFF . 8050-010 Fuel shut off valv e in the OPEN position. 8058-085 The mower dec k’ s ...
-
Husqvarna RZ3019BF - page 22
22 Bypass Linkage T ransaxle bypass linkages must be engaged when pushing or pulling the mower . The release levers ar e located on each side of the rear of the unit below the rear engine plate. See Man ual T ransport in the Operation section. 8050-018 Set bypass linkages into slots on both sides Blade Control Lever T o eng ...
-
Husqvarna RZ3019BF - page 23
23 Read the Saf ety section and following pages, if you are unfamiliar with the machine. T raining Zero turn mowers are far mor e maneuverable than typical riding mowers due to their unique steering capabilities. We suggest that this section be reviewed in its entir ety prior to attempting to move the mower under its ow ...
-
Husqvarna RZ3019BF - page 24
24 Before Starting Read the sections Safety Instructions and • Controls befor e star ting the machine. Perfor m the daily maintenance before starting • (see Maintenance Schedule in the Maintenance section). Check that there is sufcient fuel in the fuel tank. • Adjust the seat to the desired position. • The fo ...
-
Husqvarna RZ3019BF - page 25
25 Move the steering controls outwar d to the locked (outer) neutral position. Move the throttle to the middle position. If the engine is cold, the throttle contr ol knob should be pushed forward to the choke position. 8058-122 Set the throttle 8050-028 Place controls in neutral position 8058-122 Choke control ...
-
Husqvarna RZ3019BF - page 26
26 8050-135 T urn to ST ART position 8050-136 Release ignition to the R UN position 8050-010 Open the fuel valv e Open the fuel valve. Press in and turn the ignition key to the start position When the engine starts, immediately release the ignition key back to the run position. IMPORT ANT INFORMA TION Do not run the sta ...
-
Husqvarna RZ3019BF - page 27
27 Slowly push the choke control down when the engine has started. Set the desired engine speed with the thr ottle. Allow the engine to run at a moderate speed, “half throttle” for 3-5 minutes before loading it to heavily . USE FULL THROTTLE WHEN MOWING (no choke). W ARNING! Engine exhaust and certain vehicle compon ...
-
Husqvarna RZ3019BF - page 28
28 Running Release the parking brake by moving the lever 1. downward. NOTE: The mower is equipped with an operator presence system. When the engine is running, any attempt by the operator to leave the seat without rst setting the parking brake will shut off the engine. Move the steering controls to the neutral positi ...
-
Husqvarna RZ3019BF - page 29
29 Operating on Hills Read the Safety Instructions Driving on Slopes in the Saf ety Instructions . The slowest speed possible should be used • before starting up or down hills. Avoid stopping or changing speed on hills. • If stopping is absolutely necessary , pull drive • levers into the neutral position and push ...
-
Husqvarna RZ3019BF - page 30
30 Mowing Tips Observe and ag rocks and other xed objects to • avoid collisions. Begin with a high cutting height and reduce it until • the desired mowing r esult is attained. The average lawn should be cut to 2½" (64 mm) during the cool season and over 3" (76 mm) during the hot months. For healthie ...
-
Husqvarna RZ3019BF - page 31
31 Stopping the Engine Allow the engine to idle a minute in order to attain normal operating temperature before stopping it, if it has been worked hard. A void idling the engine for longer periods, as there is a risk of the spark plugs fouling. Disengage the mower deck by sliding the blade • control lever out of the l ...
-
Husqvarna RZ3019BF - page 32
32 Manual T ransport When pushing or pulling the mower , be sure to engage the EZT Hydrogear bypass linkages. The EZT bypass linkages are located on the r ear of the frame, below the rear engine guar d. Raise the deck into the highest cutting position. • Pull the EZT bypass linkages out and into the • slots. Release ...
-
Husqvarna RZ3019BF - page 33
33 Maintenance Schedule The following is a list of maintenance procedur es that must be perfor med on the machine. For those points not described in this manual, visit an authorized service workshop. An annual service carried out by an authorized service workshop is recommended to maintain your machine in the best ...
-
Husqvarna RZ3019BF - page 34
34 1) First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, r eplace every 50 hours. 2) In dusty conditions, cleaning and replacement ar e requir ed more often. 3) For daily use, the machine should be lubricated twice weekly . 4) Perfor med by authorized service workshop. ? ...
-
Husqvarna RZ3019BF - page 35
35 Battery Y our mower is equipped with a maintenance free battery that does not need servicing. However , periodic charging of the battery with an automotive type battery charger will extend its life. Keep battery and ter minals clean. • Keep battery bolts tight. • See chart for charging times. • T o clean b ...
-
Husqvarna RZ3019BF - page 36
36 Safety System The machine is equipped with a safety system that prevents starting or driving under the following conditions. The engine can only be started when: 1. The mower deck is disengaged. 2. The steering controls ar e in the outer , locked neutral position. 3. The driver is sitting in the driver’s seat. ...
-
Husqvarna RZ3019BF - page 37
37 Parking Brake Visually check that no damage is found on the lever , links, or switch belonging to the parking brake. Perfor m a standstill test and check that there is sufcient braking action. T o adjust the parking brake, contact the Husqvarna service workshop. W ARNING! Faulty adjustment can result in reduc ...
-
Husqvarna RZ3019BF - page 38
38 2 1 3 W ARNING! The engine and the exhaust system, become very hot during operation. Risk for burns if touched. Allow engine and exhaust system to cool at least two (2) minutes. EZT Belt T o replace EZT belt Park the mower on a level surface. Engage the park brake. EZT belt removal NOTE: Be careful not to damage ...
-
Husqvarna RZ3019BF - page 39
39 Adjusting the Mower Deck W ARNING! Before performing any service or adjustment checklist: 1. Engage the parking brake. 2. Place the Blade switch in the disengaged position. 3. T urn ignition switch to “OFF” position and remove the key . 4. Make sure the blades and all moving parts have completely stopped. 5. ...
-
Husqvarna RZ3019BF - page 40
40 1 2 3 Caster Wheels Check every 200 hours. Check that wheels rotate freely . If wheels do not r otate freely take the unit to your dealer for service. Foam lled tires or solid tir es will void the warranty . Removal and installation of caster wheel Remove nut (1) and caster bolt (2). 1. Pull the wheel out of ...
-
Husqvarna RZ3019BF - page 41
41 General Remove the ignition key to prevent unintentional movements during lubrication. When lubricating with an oil can, it must be lled with engine oil. When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulphide grease. For daily use, the machine should be lubricated twice ...
-
Husqvarna RZ3019BF - page 42
42 Front Wheel Mount Lubricate with a grease gun, one zerk for each wheel mount, until the grease is for ced out. Use only good quality bearing grease. Grease fr om well-known brand names (petrochemical companies, etc.) usually maintains a good quality . Front Wheel Bearings Lubricate with a grease gun, one zerk f ...
-
Husqvarna RZ3019BF - page 43
43 Problem Cause The engine will not start. Blade lever is engaged. • Steering controls ar e not locked in neutral • position. Driver is not sitting in driver’s seat. • Parking brake is not activated. • Battery is dead. • Contamination in carburetor or fuel line. • Fuel supply is closed or ...
-
Husqvarna RZ3019BF - page 44
44 Problem Cause The engine seems weak. Clogged air lter . • Fouled spark plugs. • Carburetor incorr ectly adjusted. • The engine overheats. Clogged air intake or cooling ns. • Engine overloaded. • Poor ventilation around engine. • Defective engine speed regulator . • Soot in the com ...
-
Husqvarna RZ3019BF - page 45
45 Winter Storage At the end of the mowing season, the machine should be readied for storage (or if it will not be in use for longer than 30 days). Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the carbur etor and disrupt engine function. Fuel stabilizers are an accep ...
-
Husqvarna RZ3019BF - page 46
46 ...
-
Husqvarna RZ3019BF - page 47
47 HEX HEAD CAP SCREWS The torque values shown should be used as a general guideline when specic tor que values are not given. U.S. Standard Hardware Grade SAE Grade 5 SAE Grade 8 Flangelock Screw w/Flangelock Nut Shank Size (Diameter in inches, ne or coarse thread) Size ft./lbs Nm ft./lbs Nm ft./ ...
-
Husqvarna RZ3019BF - page 48
48 1) Refer to the engine manufacturer's Owner's Manual for engine specications. 2) The power rating of the engines indicated is the average net power output (at specied rpm) of a typical production engine for the engine model measur ed to SAE standard J1349/ISO1585. Mass pr oduction eng ...
-
Husqvarna RZ3019BF - page 49
49 RZ3019 BF / 966582101 Equipment Cutting width 30" Cutting height 1½" - 4" / 2.5 cm - 10.6 cm Number of blades 1 Blade length 15" / 37 cm Sprung seat Standard Hinged armrests No Blade engagement Electric clutch Deck construction Stamped Productivity Output 1.6 acres/hr / 6475 m 2 ...
-
Husqvarna RZ3019BF - page 50
50 USA Requirements Labels are placed on the engine and/or in the engine compartment stating that the machine will fulll the requir ements. This is also applicable to special requir ements for any of the states, (Califor nia emission rules etc.). Do not remove any of these l ...
-
Husqvarna RZ3019BF - page 51
51 Delivery Service Charge the battery . q Adjust the tire pr essure of all wheels to 15 PSI (1 bar). q Mount the steering controls in the normal position. q Connect the contact box to the cabl ...
-
Husqvarna RZ3019BF - page 52
52 25-Hour Service Check the fuel pump’s air lter . q Sharpen/Replace mower bl ...
-
Husqvarna RZ3019BF - page 53
53 100-Hour Service Perfor m the 25-hour service. q Perfor m the 50-hour service. q ...
-
Husqvarna RZ3019BF - page 54
54 At Least Once Each Y ear Clean the engine’s cooling air intake (25 hours). q R ...
-
Husqvarna RZ3019BF - page 55
...
-
Husqvarna RZ3019BF - page 56
P/N 115 355026R2 09/14/10 ...
Hai una domanda su Husqvarna RZ3019BF?
Utilizza il modulo sottostante
Se non hai risolto il problema con Husqvarna RZ3019BF con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Husqvarna RZ3019BF è probabile che voglia condividere il modo di risolverlo.