-
Ryobi TS1340 - page 1
OPERA T OR'S MANUAL 10 in. (254 mm) Compound Miter Saw Model TS1340 - Double Insulated Your new Miter Saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of i ...
-
Ryobi TS1340 - page 2
Page 2 TABLE OF CONTENTS PRODUCT SPECIFICA TIONS Blade Arbor 5/8 in. (16 mm) Blade Diameter 10 in. (254 mm) Rating 120 volts, 60Hz, AC Only No Load Speed 5000 RPM Input 1 4 Amperes Net Weight 29.92 lbs. (13.6 kg.) INTRODUCTION Y our saw has many features for making cutting operations more pleasant and enjoyable. Safety , performance, and dependabil ...
-
Ryobi TS1340 - page 3
Page 3 RULES FOR SAFE OPERA TION DOUBLE INSULA TION Double insulation is a concept in safety , in electric power tools, which eliminates the need for the usual three-wire ground power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. W A ...
-
Ryobi TS1340 - page 4
Page 4 Safe operation of this power tool requires that you read and understand this operator's manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your miter saw works. READ ALL INSTRUCTIONS ■ KNOW YOUR POWER TOOL. Read the operator's manual carefully. Learn the saw's a ...
-
Ryobi TS1340 - page 5
Page 5 ■ NEVER reach behind, under, or within three inches of the blade and its cutting path with your hands and fingers for any reason. ■ NEVER hand hold a workpiece that is too small to be clamped. Keep hands clear of the no hands zone. ■ NEVER reach to pick up a workpiece, a piece of scrap, or anything else that is in or near the cutting p ...
-
Ryobi TS1340 - page 6
Page 6 SA VE THESE INSTRUCTIONS RULES FOR SAFE OPERA TION ■ STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush. ■ MAKE SURE THE WORK AREA HAS AMPLE LIGHT- ING to see the work and that no obstructions will interfere with safe operation BEFORE performing any work usi ...
-
Ryobi TS1340 - page 7
Page 7 UNP ACKING ■ Lift the saw arm by the handle. Hand pressure should remain on the saw arm to prevent sudden rise upon release of the tie wrap. ■ Examine all parts to make sure no breakage or damage has occurred during shipping. If any parts are missing, do not attempt to assemble the miter saw, plug in the power cord, or turn the switch on ...
-
Ryobi TS1340 - page 8
Page 8 The following items are included with your Compound Miter Saw: ■ 10 in. (254 mm) Saw Blade ■ Miter Lock Handle ■ Dust Bag ■ Dust Guide LOOSE P ARTS LIST ■ Work Clamp ■ Blade Wrench ■ Operator's Manual ■ Warranty Registration Card Fig. 1 SAW BLADE DUST GUIDE WARNING: The use of attachments or accessories not listed might ...
-
Ryobi TS1340 - page 9
Page 9 FEA TURES KNOW YOUR COMPOUND MITER SAW See Figure 2. Before attempting to use your saw, familiarize yourself with all operating Features and Rules for Safe Operation. W ARNING: Do not allow familiarity with your saw to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. 15 AMP MOTOR Your s ...
-
Ryobi TS1340 - page 10
Page 10 FEA TURES BLADE WRENCH / ST ORAGE AREA See Figure 2. A blade wrench is packed with your saw . One end of the wrench is a phillips screwdriver and the other end is a 1/4 in. (6.4 mm) hex key . Use the hex key end when installing or removing blade and the phillips end when removing or loosening screws. A storage area for the blade wrench is l ...
-
Ryobi TS1340 - page 11
Page 11 15 30 45 0 15 30 45 FEA TURES POSITIVE STOPS ON MITER TABLE Positive stops have been provided at 0 ° , 15 ° , 22-1/2 ° , 30 ° , and 45 ° . The 22-1/2 ° and 45 ° positive stops have been provided on both the left and right side of the miter table. BEVEL LOCK KNOB The bevel lock knob securely locks your compound miter saw at desired be ...
-
Ryobi TS1340 - page 12
Page 12 ASSEMBL Y W ARNING: To prevent accidental starting that could cause possible serious personal injury, assemble all parts, make sure all adjustments are complete, and make sure all fasteners are secure before connecting saw to power supply. Saw should never be connected to power supply when you are assembling parts, making adjustments, insta ...
-
Ryobi TS1340 - page 13
Page 13 ...
-
Ryobi TS1340 - page 14
Page 14 1 5 45 30 45 30 3 1.6 31.6 5 1 22.5 ASSEMBL Y CAUTION: Always install the blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw. The direction of blade rotation is also stamped with an arrow on the upper blade guard. ■ Tighten blade bolt securely. ■ Replace the lower blade guard ...
-
Ryobi TS1340 - page 15
Page 15 ADJUSTMENTS W ARNING : Failure to unplug your saw could result in accidental starting causing possible serious personal injury. ■ Push down on the saw arm and pull out the lock pin to release the saw arm. ■ Raise saw arm to its full raised position. ■ Loosen the miter lock handle approximately one-half turn. ■ Depress the miter lock ...
-
Ryobi TS1340 - page 16
Page 16 ...
-
Ryobi TS1340 - page 17
Page 17 ...
-
Ryobi TS1340 - page 18
Page 18 ADJUSTMENTS BEVEL PIVOT ADJUSTMENT ■ Your compound miter saw should bevel easily by loos- ening the bevel lock knob and tilting the saw arm to the left. ■ If movement is tight or if there is play in the pivot, have saw repaired by at your nearest RYOBI AUTHORIZED SERVICE CENTER. W ARNING: Do not start your compound miter saw without che ...
-
Ryobi TS1340 - page 19
Page 19 CUTTING WITH YOUR COMPOUND MITER SAW W ARNING: When using a work clamp or C-clamp to secure your workpiece, clamp workpiece on one side of the blade only. The workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece. The workpiece binding the blade will cause motor stalling and kickback. This situat ...
-
Ryobi TS1340 - page 20
Page 20 BEVEL SCALE INDICATOR SCREW SCALE INDICATOR OPERA TION ■ Pull out the lock pin and lift saw arm to its full height. ■ Loosen the miter lock handle. Rotate the miter lock handle approximately one-half turn to the left to loosen. ■ Press the miter lock plate down with your thumb and hold. ■ Rotate the control arm until the pointer ali ...
-
Ryobi TS1340 - page 21
Page 21 OPERA TION ■ Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when possible. See Figure 27. W ARNING: To avoid serious personal injury, always keep your hands outside the no hands zone; at least 3 in. (7.6 cm) from blade. Never perform any cutting operat ...
-
Ryobi TS1340 - page 22
Page 22 ■ Recheck miter angle setting. Make a test cut in scrap material. ■ Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board could collapse on the blade at the end of the cut, jamming the blade. See Figures 32 and ...
-
Ryobi TS1340 - page 23
Page 23 CUTTING COMPOUND MITERS To aid in making the correct settings, the compound angle setting chart below has been provided. Since compound cuts are the most difficult to accurately obtain, trial cuts should be made in scrap material, and much thought and planning made, prior to making your required cut. OPERA TION 4 PITCH OF SIDE NUMBER OF SID ...
-
Ryobi TS1340 - page 24
Page 24 When setting the bevel and miter angles for compound miters, remember that the settings are interdependent; chang- ing one angle changes the other angle as well. Keep in mind that the angles for crown moldings are very precise and difficult to set. Since it is very easy for these angles to shift, all settings should first be tested on scrap ...
-
Ryobi TS1340 - page 25
Page 25 ...
-
Ryobi TS1340 - page 26
Page 26 W ARNING: When servicing, use only identical Ryobi replacement parts. Use of any other part may create a hazard or cause product damage. GENERAL Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, ...
-
Ryobi TS1340 - page 27
Page 27 NOTES ...
-
Ryobi TS1340 - page 28
Page 28 983000-248 3-03 RYOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road Anderson SC 29625 Post Office Box 1207 Anderson SC 29622-1207 Phone 1-800-525-2579 www.ryobitools.com EXTENSION CORD CAUTION When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the ...
Hai una domanda su Ryobi TS1340?
Utilizza il modulo sottostante
Se non hai risolto il problema con Ryobi TS1340 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Ryobi TS1340 è probabile che voglia condividere il modo di risolverlo.