-
Chicago Electric 41213 - page 1
7” ELECTRIC POLISHER / SANDER Model 41213 SET UP AND OPERA TING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally . Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit o ...
-
Chicago Electric 41213 - page 2
Page 2 SKU 41213 For technical questions, please call 1-800-444-3353. SA VE THIS MANUAL Keep this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures. Write the product’ s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product ha ...
-
Chicago Electric 41213 - page 3
Page 3 SKU 41213 For technical questions, please call 1-800-444-3353. GENERAL SAFETY RULES W ARNING! Read all instructions Failure to follow all instructions listed below may result in electric shock, re, and/or serious injury . The term “power tool” in all of the warnings listed below refers to your line-operated (corded) power tool or batt ...
-
Chicago Electric 41213 - page 4
Page 4 SKU 41213 For technical questions, please call 1-800-444-3353. Avoid accidental starting. Ensure the switch is in the of f-position before plug- ging in. Carrying power tools with your nger on the switch or plugging in power tools that have the switch on invites accidents. Remove any adjusting key or wrench before turning the power tool o ...
-
Chicago Electric 41213 - page 5
Page 5 SKU 41213 For technical questions, please call 1-800-444-3353. Service Have your power tool serviced by a qualied repair person using only identi - cal replacement parts. This will ensure that the safety of the power tool is maintained . VIBRA TION HAZARD This tool vibrates during use. Repeated or long-term exposure to vibration may cause ...
-
Chicago Electric 41213 - page 6
Page 6 SKU 41213 For technical questions, please call 1-800-444-3353. (1) Do not force the Polisher/Sander . This tool will do the work better and safer at the speed and capacity for which it was designed. Do not force the pads into the vehicle being waxed/polished. Apply moderate pressure, allowing the Bonnet to rotate freely without being forced. ...
-
Chicago Electric 41213 - page 7
Page 7 SKU 41213 For technical questions, please call 1-800-444-3353. When using the polisher , maintain a rm grip on the tool with both hands to resist starting torque. Use clamps (not included) or other practical ways to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lea ...
-
Chicago Electric 41213 - page 8
Page 8 SKU 41213 For technical questions, please call 1-800-444-3353. GROUNDING Improperly connecting the grounding wire can result in electric shock. Check with a qualied electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from ...
-
Chicago Electric 41213 - page 9
Page 9 SKU 41213 For technical questions, please call 1-800-444-3353. dard Association, and the National Electrical Code. (See Outlets for 2-Prong Plug.) Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Extension Cords Grounded tools require a three wire extens ...
-
Chicago Electric 41213 - page 10
Page 10 SKU 41213 For technical questions, please call 1-800-444-3353. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120/240 VOL T) NAMEPLA TE AMPERES (at full load) EXTENSION CORD LENGTH 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – ...
-
Chicago Electric 41213 - page 11
Page 1 1 SKU 41213 For technical questions, please call 1-800-444-3353. SPECIFICA TIONS Electrical Requirements 1 10 V~ / 60 Hz / 6 A (load) Motor No Load Speed 2 Speed (2800/ 3300) Arbor Diameter 7/8” Spindle Thread 5/8” - 1 1 UNP ACKING When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broke ...
-
Chicago Electric 41213 - page 12
Page 12 SKU 41213 For technical questions, please call 1-800-444-3353. Depress the Stop Pin (3). Using the Wrench (49), T ighten the Flange Nut (47) by turning it clockwise until rmly in place. See Figure 1 below . Wrap a clean Polishing Bonnet (48) on top of the Backing Pad (46). T ie it se- curely using the drawstring. Make sure to tuck any ex ...
-
Chicago Electric 41213 - page 13
Page 13 SKU 41213 For technical questions, please call 1-800-444-3353. Controls Polishing Place a clean Polishing Bonnet (48) securely onto the Backing Pad (46). T ie it securely using the drawstring. Make sure to tuck any excess string inside the Bonnet Note: Prior to waxing or polishing a vehicle, make sure it’s surface has been thoroughly wash ...
-
Chicago Electric 41213 - page 14
Page 14 SKU 41213 For technical questions, please call 1-800-444-3353. 15 to 25 Degrees T o start, grip the Polisher rmly with both hands and press in on the ON/OFF Switch (24). Press the Lock-ON Button (22) to lock the Switch in the ON posi- tion. Press the ON/OFF Switch (24) in again to unlock it. Position the unit on the area to be polished. ...
-
Chicago Electric 41213 - page 15
Page 15 SKU 41213 For technical questions, please call 1-800-444-3353. Place a sanding disk, with a hole in the center of it, onto the Backing Pad (46) and secure it with the Flange Nut (47). T ighten the Flange Nut (47) using the Spanner Wrench (49). See Assembly Diagram and Parts List pages 16 and 17. Plug the Power Cord (33) of the Polisher/Sand ...
-
Chicago Electric 41213 - page 16
Page 16 SKU 41213 For technical questions, please call 1-800-444-3353. MAINTENANCE AND SERVICING Risk of serious personal injury from accidental starting or electric shock. T urn the Power Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures ...
-
Chicago Electric 41213 - page 17
Page 17 SKU 41213 For technical questions, please call 1-800-444-3353. Part # Description Qty Part # Description Qty 1 Screw 1 26 Brand 1 2 W asher 1 27 W asher 1 3 Stop Pin 1 28 Screw 1 4 Spring 1 29 Screw 1 5 Gear Box 1 30 Screw 1 6 Bearing 1 31 Cord Clip 1 7 Bearing Cover 1 32 Cord Armor 1 8 Screw 1 33 Cord 1 9 Pinion Gear 1 34 Side Handle 1 10 ...
-
Chicago Electric 41213 - page 18
Page 18 SKU 41213 For technical questions, please call 1-800-444-3353. ASSEMBL Y DIAGRAM Note: Some parts are listed and shown for illustration purposes only , and are not avail- able individually as replacement parts. ...
-
Chicago Electric 41213 - page 19
Page 19 SKU 41213 For technical questions, please call 1-800-444-3353. Record Product’ s Serial Number Here: Note: If product has no serial number , record month and year of purchase instead. LIMITED 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants ...
Hai una domanda su Chicago Electric 41213?
Utilizza il modulo sottostante
Se non hai risolto il problema con Chicago Electric 41213 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Chicago Electric 41213 è probabile che voglia condividere il modo di risolverlo.