Italiano dropdown-ico

Manuale per l’uso NEC NEC MultiSync LCD3210 LCD3210 LCD3210

38 pagine 0.33 mb
Scarica

Vai alla pagina of 38

Summary
  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 1

    (1/38) External Contro l LCD3210 1. Application This document defines the communications method for control of the LCD3210 when using an external controller . 2. Connectors and wiring Connector: D-Sub 9-pin Cable: Cross (reversed) cable or null modem cable 3. Communication Parameter (1) Communication system Asynchronous (2) Interface RS-232C (3) Ba ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 2

    (2/38) 4. Communication Format The command packet consists of four parts, Header, Message, Check code and Delimiter. Sequence of a typical procedure to control a monitor is as follows, [A controller and a monitor, two-way communication composition figure] 4.1 Header block for mat (fixed lengt h) 1 st byte) SOH: Start of Header ASCII SOH (01h) 2 nd ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 3

    (3/38) 4 th byte) Source: Source equipment ID. (Sender) Specify a sender address. The controller must be ‘0’(30h). 5 th byte) Message Type: (Case sensitive.) Refer to section 4.2 “Message block format” for more details. ASCII 'A' (41h): Command ASCII 'B' (42h): Command reply. ASCII 'C' (43h): Get current parame ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 4

    (4/38) 3 ） Set parameter The controller sends this message to change a setting of the monitor. Message format of the “Set parameter” is as follows;  Refer to section 5.3 “Set parameter” for more details. 4 ） Set Parameter reply The monitor replies with this message for a confirmation of the “Set parameter message”. Message format ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 5

    (5/38) Following is an example of a Check code (BCC) calculation. Check code (BCC) D 17 = D 1 xor D 2 xor D 3 xor … xor D 14 xor D 15 xor D 16 = 30h xor 41h xor 30h xor 45h xor 30h xor 41h xor 02h xor 30h xor 30h xor 31h xor 30h xor 30h xor 30h xor 36h xor 34h xor 03h = 7 7 h 4.6 Del imiter Packet delimiter code; ASCII CR(0Dh). Header Message SOH ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 6

    (6/38) 5. Message type 5.1 Get curr ent Paramet er from a monitor . Send this message when you want to get the status of a monitor. For the status that you want to get, specify the “OP code page” the “OP code”, refer to “Appendix A. Operation code table”. 1 st byte) STX: Start of Message ASCII STX (02h) 2 nd -3 rd bytes) OP code page: O ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 7

    (7/38) 00h: No Error. 01h: Unsupported operation with this monitor or unsupported operation under current condition. This result code from the monitor is encoded to ASCII characters. Ex.) The byte data 01h is encoded to ASCII character '0' and '1' (30h and 31h). 4 th –5 th bytes) OP code page: Operation code page. These bytes ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 8

    (8/38) Ex) The byte data 02h must be encoded to ASCII '0' and '2' (30h and 32h). Refer to the Operation code table. 4 th -5 th bytes) OP code: Operation code This OP code data must be encoded to ASCII characters. OP code 1Ah -> OP code (Hi) = ASCII '1' (31h) OP code (Lo) = ASCII 'A' (41h) Refer to the Oper ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 9

    (9/38) ASCII '0''1' (30h, 31h): Momentary Like Auto Setup function, that automatically changes the parameter. 10 th -13 th bytes) Max. value: Maximum value that monitor can accept. (16bits) Reply data from the monitor is encoded to ASCII characters. Ex.) '0''1''2''3' means 0123h (291) 14 t ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 10

    (10/38) Bit 5-2 Reserved (Don't care) Bit 1 1:Positive Horizontal sync polarity. 0:Negative Horizontal sync polarity. Bit 0 1:Positive Vertical sync polarity. 0:Negative Vertical sync polarity.  H Freq: Horizontal Frequency in unit 0.01kHz  V Freq: Vertical Frequency in unit 0.01Hz Ex.) When H Freq is '1''2''A&ap ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 11

    (11/38) Delimiter CR (0Dh): End of packet Step 2. The monitor replies with current Brightness setting and capability to support this operation. Header SOH (01h): Start Of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller 'A' (41h): Monitor ID LCD3210 must be ASCII 'A' (41h). 'D&apo ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 12

    (12/38) Step 4. The monitor replies with a message for confirmation. Header SOH (01h): Start Of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller 'A' (41h): Monitor ID LCD3210 must be ASCII 'A' (41h). 'F' (46h): Message Type is "Set parameter reply" '1'-&ap ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 13

    (13/38) 6.2. How to read the measuremen t value of the built-in temperature sensors. LCD3210 has two built-in temperature sensors. The controller can monitor inside temperatures by using those sensors through RS-232C. The following shows the procedure for reading the temperatures from the sensors. Step 1. Select a temperature sensor which you want ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 14

    (14/38) Delimiter CR (0Dh): End of packet Step 3. The controller requests the monitor to send the temperature from the selected sensor. Header Message Check code Delimiter SOH-'0'-'A'-'0'-'C'-'0'-'6' STX-'0'-'2'-'7'-'9'-ETX BCC CR Header SOH (01h): S ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 15

    (15/38) ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.5 “Check code” for a BCC calculation. Delimiter CR (0Dh): End of packet 7. Power control procedure 7.1 Power status read 1) The controller requests the monitor to reply a current power status. Header Message Check code Delimiter SOH-'0'-'A&a ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 16

    (16/38) Check code BCC: Block Check Code Refer to the section 4.5 “Check code” for a BCC calculation. Delimiter CR (0Dh): End of packet 7.2 Power con trol 1) The controller requests the monitor to control monitor power. Header SOH (01h): Start Of Header '0' (30h): Reserved 'A' (41h): Monitor ID LCD3210 must be ASCII 'A& ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 17

    (17/38) Check code BCC: Block Check Code Refer to the section 4.5 “Check code” for a BCC calculation. Delimiter CR (0Dh): End of packet. ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 18

    (18/38) 8. Asset Data read and write 8.1 Asset Data Read Requ est and repl y This command is used in order to read Asset Data. 1) The controller requests the monitor to reply with Asset data. Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-'0'-'A' STX-'C'-'0'-&a ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 19

    (19/38) 8.2 Asset D ata write This command is used in order to write Asset Data. 1) The controller requests the monitor to write Asset data. Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-N-N STX-'C'-'0'-'0'-'E'-'0'-'0'- Data(0)-Data(1)---Da ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 20

    (20/38) 9. Date & Time read and write 9.1 Da te & Ti me Read This command is used in order to read the setting of Date & Time. 1) The controller requests the monitor to reply with the Date & Time. Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-'0'-'6' STX-'C&a ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 21

    (21/38) WW: weekdays '0'-'0'(30h, 30h): Sunday '0'-'1'(30h, 31h): Monday '0'-'2'(30h, 32h): Tuesday '0'-'3'(30h, 33h): Wednesday '0'-'4'(30h, 34h): Thursday '0'-'5'(30h, 35h): Friday '0'-'6'(30h, 36h): Saturday ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 22

    (22/38) WW: weekdays '0'-'0'(30h, 30h): Sunday '0'-'1'(30h, 31h): Monday '0'-'2'(30h, 32h): Tuesday '0'-'3'(30h, 33h): Wednesday '0'-'4'(30h, 34h): Thursday '0'-'5'(30h, 35h): Friday '0'-'6'(30h, 36h): Saturday ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 23

    (23/38) WW: weekdays '0'-'0'(30h, 30h): Sunday '0'-'1'(30h, 31h): Monday '0'-'2'(30h, 32h): Tuesday '0'-'3'(30h, 33h): Wednesday '0'-'4'(30h, 34h): Thursday '0'-'5'(30h, 35h): Friday '0'-'6'(30h, 36h): Saturday ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 24

    (24/38) 10.Schedule read and write 10.1 Schedule Read This command is used in order to read the setting of the Schedule. 1) The controller requests the monitor to read Schedule Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-'0'-'8' STX-'C'-'2'-'1'-&ap ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 25

    (25/38) OFF_HOUR: Turn off time (hour) '0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): Off timer isn't set. OFF_MIN: Turn off time (minute) '0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 (=3Bh) '3'-'C'(3 ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 26

    (26/38) 10.2 Schedule Write This command is used in order to write the setting of the Schedule. 1) The controller requests the monitor to write Schedule . Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-'1'-'6' STX-'C'-'2'-'1'-'4'-PG-ON HOURS ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 27

    (27/38) EX. '0'-'1'(30h, 31h): Monday '0'-'4'(30h, 34h): Wednesday '0'-'F'(30h, 46h): Monday, Tuesday, Wednesday and Thursday '7'-'F'(37h, 46h): Monday to Sunday FL: Option bit 0: Everyday bit 1: Every week bit 2: Schedule Disable/Enable * When bit0 and bit1 are '1 ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 28

    (28/38) ON_MIN: Turn on time (minute) '0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 '3'-'C'(33h, 43h): On timer isn’t set. OFF_HOUR: Turn off time (hour) '0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): Off ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 29

    (29/38) 3) The controller requests the monitor to write Enable/Disable Schedule. Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-'0'-'A' STX-'C'-'2'-'1'-'5'-PG-EN-ETX BCC CR Header SOH (01h): Start Of Header '0' (30h): Reserved &apo ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 30

    (30/38) BCC: Block Check Code Refer to the section 4.5 “Check code” for a BCC calculation. Delimiter CR (0Dh): End of packet 11. Self diagnosis 11.1 Self-diagnosi s status rea d This command is used in order to read the Self-diagnosis status. 1) The controller requests the monitor to read Self-diagnosis status. Header Message Check code Delimit ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 31

    (31/38) ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.5 “Check code” for a BCC calculation. Delimiter CR (0Dh): End of packet ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 32

    (32/38) 12. Serial No. & Model Name Read 12.1 Serial No. Read This command is used in order to read a serial No. 1) The controller requests the monitor to read a serial No. Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-'0'-'6' STX-'C'-'2'-'1'-&ap ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 33

    (33/38) Header SOH (01h): Start Of Header '0' (30h): Reserved 'A' (41h): Monitor ID LCD3210 must be ASCII 'A' (41h). '0' (30h): Message sender is the controller 'A' (41h): Message type is "Command" '0'-'6'(30h, 36h): Message length. Message STX (02h): Start of Message & ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 34

    (34/38) Appendix A. Operation Code (OP code) Table Item OP code page OP code Parameter Remarks Brightness 00h 10h 0: dark | MAX.: bright Contrast 00h 12h 0: low | MAX.: high Sharpness 00h 8Ch 0: dull | MAX.:sharp Tint 00h 90h 0: | MAX.: Color 02h 1Fh 0: pale | MAX.: deep Black Level 00h 92h 0: dark | MAX.: bright Noise Reduction 02h 20h 0: Off | MA ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 35

    (35/38) Item OP code page OP code Parameter Remarks Zoom V-Position 02h CDh 0: Down side | Max.: Up side Screen reset 00h 06h 1: Reset Momentary Balance 00h 93h O: Left | 50:(Center) | 100: Right Treble 00h 8Fh O: Min. | 50:(Center) | 100: Max. Bass 00h 91h 0: Min. | 50:(Center) | 100: Max. AUDIO Audio reset 02h 31h 1: Reset Momentary PIP Size 02h ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 36

    (36/38) Item OP code page OP code Parameter Remarks VIDEO EQ. 02h E0h 0: | 7: LongCable Manual SYNC Terminate 02h E1h 1:Hi(2.2kohm) 2:Lo(75ohm) OSM Turn Off 00h FCh 0-9:Do not set. 10:10s 11:11s | 240:240s Information OSM 02h 3Dh 0:disable information OSM 3-10: OSM timer [seconds] Off Timer 02h 2Bh 0: OFF 1: 1 hour | 24: 24 hours 1 hour/step H Posi ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 37

    (37/38) Item OP code page OP code Parameter Remarks Power On Delay 02h D8h 0: OFF (0sec) │ 50:50sec Advanced Option Reset 02h E4h 1:RESET Momentary Input 00h 60h 3: RGB1 (DVI-D) 1: RGB2 (D-SUB) 2: RGB3 (BNC) 12: DVD/HD 5: VIDEO (Composite) 7: S-VIDEO Picture Mode 02h 1Ah 1: sRGB 3: Hi-Bright 4: Standard 5: Cinema SRGB: PC mode only Cinema: A/V mo ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 38

    (38/38) All data are subject to change without notice. Copyright 2004-2005 NEC Display Solutions All Right Reserved This document p rovides the technical info rmation for users. NEC Disp lay Solutions reserv es the right to ch ange or modify the i n form ation containe d herei n without notice. NEC Disp lay Solutions makes no warranty for the use o ...

Fabbricante NEC Categoria Computer Monitor

I documenti che otteniamo dal fabbricante del dispositivoNEC NEC MultiSync LCD3210 LCD3210 LCD3210 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici NEC
- manuali per l’uso MultiSync LCD3210 LCD3210 LCD3210
- schede prodotto NEC
- opuscoli
- o etichette energetiche NEC NEC MultiSync LCD3210 LCD3210 LCD3210
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso NEC NEC MultiSync LCD3210 LCD3210 LCD3210.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione NEC NEC MultiSync LCD3210 LCD3210 LCD3210, manuali di manutenzione, brevi manuali o manuali utente NEC NEC MultiSync LCD3210 LCD3210 LCD3210. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto NEC NEC MultiSync LCD3210 LCD3210 LCD3210.

Manuali per l’uso simili

Manuale completo del dispositivo NEC NEC MultiSync LCD3210 LCD3210 LCD3210, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare NEC NEC MultiSync LCD3210 LCD3210 LCD3210 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti NEC NEC MultiSync LCD3210 LCD3210 LCD3210.

Il manuale per l’uso completo NEC, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice NEC NEC MultiSync LCD3210 LCD3210 LCD3210, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per NEC NEC MultiSync LCD3210 LCD3210 LCD3210 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - che ci dovrebbe aiutare nei primi passi durante l'uso NEC NEC MultiSync LCD3210 LCD3210 LCD3210
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del NEC NEC MultiSync LCD3210 LCD3210 LCD3210
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio NEC NEC MultiSync LCD3210 LCD3210 LCD3210 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su NEC NEC MultiSync LCD3210 LCD3210 LCD3210?

Utilizza il modulo sottostante

Se non hai risolto il problema con NEC NEC MultiSync LCD3210 LCD3210 LCD3210 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con NEC NEC MultiSync LCD3210 LCD3210 LCD3210 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)