Gilson 600MPの取扱説明書

28ページ 0.48 mb
ダウンロード

ページに移動 of 28

Summary
  • Gilson 600MP - page 1

    GILS J J N MIXERS MORTAR-PLASTER MIXER MODEL: 600MP OPERATOR’S GUIDE & PARTS MANUAL GILS J J N MIXERS BY 4343 Easton Road · St. Joseph, MO 64503 816-233-4840 · 800-253-3676 Fax 816-233-4624 · 888-253-3676 E-Mail: cleform@ccp.com Web Address: www.cleform.com ...

  • Gilson 600MP - page 2

    1 INTRODUCTION This operator’s manual has been prepared to provide the information you need to correctly operated and maintain your mixer. For maximum satisfaction, carefully read and follow the instructions in this manual. Should you need repair parts or service, refer to the parts breakdown on pages 14 through 25. Information regarding operatio ...

  • Gilson 600MP - page 3

    2 TABLE OF CONTENTS 1. SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. ASSEMBLY AND PREOPERATIONAL CHECKS . . . . . . . 4 3. CONTROLS AND OPERATION Clutch Control Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Tow Pole Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Safety Ch ...

  • Gilson 600MP - page 4

    3 1 – SAFETY PRECAUTIONS THE FOLLOWING PRECAUTIONS ARE SUGGESTED TO HELP PREVENT ACCIDENTS. A CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS CAN BE AVOIDED BY OBSERVING CERTAIN PRECAUTIONS. READ AND PRACTICE THE FOLLOWING PRECAUTIONS BEFORE OPERATING THIS EQUIPMENT TO HELP PREVENT ACCIDENTS. EQUIPMENT SHOULD BE OPERATED ONLY BY THOSE WHO A ...

  • Gilson 600MP - page 5

    4  Never charge or fill the unit prior to starting the mixing blades as an overload encountered in starting a loaded unit could damage the engine/motor or drive components.  Connect safety chains as instructed when towing the mixer. Connect only to correct hitch or coupler.  Keep warning, caution and safety instruction labels clean and in ...

  • Gilson 600MP - page 6

    5 3 – CONTROLS AND OPERATIONS 1. The mixing paddles feature adjustable rubber wipers and steel backing plates. Paddles are factory preset for appropriate drum wrap clearance. If adjustment is required, proceed as follows: A. Loosen the wiper attaching hardware and move the wiper outward to maintain contact with the drum but without folding over w ...

  • Gilson 600MP - page 7

    6 TOW POLE ASSEMBLY The tow pole assembly is located on the front of the mixer and is used for transport only. For transport, pull the tow pole assembly out, line up the hold and insert the L-shaped pin through holes. When operating the mixer, pull the L-shaped pin out of the hole and push tow pole assembly all the way in. Line up the holes and ins ...

  • Gilson 600MP - page 8

    7 4 – MIXER TRANSPORT 1. Secure drum by engaging drum lock. 2. Secure all moveable parts, including the rear housing. 3. Secure tow pole coupler to vehicle and attach safety chains and hooks. (See FIGURE 2 , Safety Chains). A. Pintle type couplers require the appropriate tow vehicle coupler retainer. B. Match ball coupler size exactly with hitch ...

  • Gilson 600MP - page 9

    8 LOADING THE MIXER When the mixing blades are rotating, pour the required amount of water into the drum , then add cement, sand and lime. The desired mixing speed is 33 RPM DISCHARGING THE MIXER Allow the entire mixture to mix for one (1) full minute. DO NOT STOP MIXER FROM ROTATING. Hold the tilt handle and disengage the drum lock. Dump mortar to ...

  • Gilson 600MP - page 10

    9 TROUBLE SHOOTING GUIDE FOR MP MIXERS. ENGINE WON’T START: 1. Check for sufficient fuel. 2. Check oil level (some engines have an oil alert, preventing the engine from starting when oil level is low) 3. Was engine choked when starting? 4. Is engine flooded? 5. Check spark plug. (Clean and check gap). 6. If engine still won’t start, take to ser ...

  • Gilson 600MP - page 11

    10 6 – OPERATING GUIDELINES MASONRY CONSTRUCTION GUIDELINES The strength and durability of brick masonry depends upon the quality of the brick, the quality of the mortar and the workmanship in laying. The strength also depends upon adequate bond and the shape of the masonry unit. Brick quality – Characteristics are hardness and density. Brick f ...

  • Gilson 600MP - page 12

    11 MIXING SHAFT BEARINGS The mixing shaft bearings are permanently factory sealed and lubricated, and should not require further service. DRUM SHAFT BEARING HANGERS Drum bearing hangers are located on each side of the drum, and are equipped with grease fittings. These bearings should be lubricated once each week with lithium based grade 2 multi-pur ...

  • Gilson 600MP - page 13

    12 8 – ADJUSTMENT RUBBER WIPER BLADES Adjust rubber wipers so they fit snugly against the drum but not to the point that they fold over when the blades rotate. ENGINE/MOTOR DRIVE SEE FIGURE 4. 1. Align pulleys correctly 2. Tighten locking collars in the direction of rotation and tighten setscrews. 3. Adjust tension on the engine belt as follows: ...

  • Gilson 600MP - page 14

    13 9 – STORAGE For short term storage, clean the mixer and store in a dry place. If the mixer is not to be used for an extended period of time, service the mixer completely and store in a dry place. 1. Refer to the engine/motor instructions for storage instructions. 2. Cover exposed metal surfaces with a thin coat of SAE 30 weight engine oil. 3. ...

  • Gilson 600MP - page 15

    14 ...

  • Gilson 600MP - page 16

    15 Concrete Mixer Parts List REF NO. PART NO. DESCRIPTION QTY DRUM & DRIVE 1 232255 Bearing Hanger 2 2 1031 Grease Fitting 4 3 214837 Gear 1 4 5079 Drum Sheel Assembly 1 5 5207 Grill Assembly 1 6 232392 Bearing Support Assembly 2 7 245704 Drum Tilt Lever 1 8 5771 Drum Seal 2 9 245349 Houseing, Seal 2 10 5772 O-ring Seal Clamp 2 11 5773 O-Ring 2 ...

  • Gilson 600MP - page 17

    16 ...

  • Gilson 600MP - page 18

    17 Concrete Mixer Parts List MIXING BLADES REF NO. PART NO. DESCRIPTION QTY 1 245711 Mixing Arm Assembly, Tow End 2 2 245709 Mixing Arm Assembly, Engine End 2 3 245705 MixingArm Cap 4 4 5235 Drum Wrap Wiper 4 5 5234 Wrap Wiper Backing Plate 4 6 5230 End Wiper Backing Plate 2 7 5231 Drum End Wiper 2 8 *70343 Capscrew, Hex HD 1/2-13 x 1 1/2 Gr 5 10 9 ...

  • Gilson 600MP - page 19

    18 ...

  • Gilson 600MP - page 20

    19 Concrete Mixer Parts List ENGINE HOUSING AND AXLE REF NO. PART NO. DESCRIPTION QTY 1 245712 Engine Housing Assembly w/decals 1 2 245701 Housing Base Assembly 1 3 32082 Reflector 2 4 232623 T-Handle Latch 2 5 5402 Handle, Engine Housing 1 6 220521 Rivet, Handle 4 7 223590 Rubber Bumper 4 8 232614 Housing Base Front Plate 1 9 213297 Screw, Thread ...

  • Gilson 600MP - page 21

    20 ...

  • Gilson 600MP - page 22

    21 Concrete Mixer Parts List FRAME, DRIVE AND CLUTCH CONTROL REF NO. PART NO. DESCRIPTION QTY 1 245265 Frame, Engine and Drive Support 1 2 245281 Frame Assembly 1 3 232276 Pin and Chain Assembly 1 4 *70731 Pin, Cotter 3/16 x 1 1 5 *2776 Spring Clip 1 6 232301 Tow Pole Assembly Pintle (std) 1 7 *71215 Capscrew, Hex Hd 1/2-13 x 3 1/4 Gr 5 1 8 245426 ...

  • Gilson 600MP - page 23

    22 ...

  • Gilson 600MP - page 24

    23 Concrete Mixer Parts List ENGINE AND POWER OPTIONS REF NO. PART NO. DESCRIPTION QTY 1 232412 Belt Guide, Upper 1 2 245339 Belt Guide, Lower (Angled Bracket) 1 3 *70631 Nut, Hex 3/8-16 Cone Lock 3 4 *70703 Washer, 3/8 Flat 4 5 232548 Pivot Blocks, Engine Plate 2 6 *70258 Capscrew, Hex Hd 3/8-16 x 2 Gr 5 4 7 *70553 Nut, Hex 3/8-16 4 8 *70649 Washe ...

  • Gilson 600MP - page 25

    24 ...

  • Gilson 600MP - page 26

    25 Mixer Parts List ENGINE AND POWER OPTIONS MP600 Model 59299 REF. # PART # DESCRIPTION QUANTITY 14 245200 Engine, Honda GX240HA 8 HP 1 15 245400 Engine Mount Plate 1 16 239969 Belts (set of 2) 1 17 5254 Pulley, Drive 5 3/4 O.D. 1 18 5240 Pulley, Driven 8 1/4 O.D. 1 19 *70170 Capscrew, Hex Hd 5/16-18 x 1 3/4 Gr 5 4 MP600 Model 59297 14 29055 Engin ...

  • Gilson 600MP - page 27

    26 GILSON MIXER WARRANTY WARRANTY: This mixer is warranted to the original purchaser only, to be free of defects in material and workmanship under normal use, for one year from purchase date. Cleform Tool Corp. shall without charge, repair or replace parts which are found to be defective. All transportation charges for replacement parts must be bor ...

  • Gilson 600MP - page 28

    27 WARRANTIES ARE EXCLUDED AND DISCLAIMED AFTER THE EXPIRATION OF SUCH PERIOD. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitations of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may als ...

メーカー Gilson カテゴリー Mixer

Gilson 600MPのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 600MPの取扱説明書
- Gilsonの製品カード
- パンフレット
- またはGilson 600MPの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Gilson 600MPの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Gilson 600MPの取り付け説明書、サービスマニュアル、簡易説明書、またはGilson 600MPのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Gilson 600MPの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Gilson 600MPデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGilson 600MPを使用するのを助ける技術的文書のことです。説明書は通常、全てのGilson 600MPユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Gilsonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Gilson 600MPの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGilson 600MPの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Gilson 600MPに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Gilson 600MPデバイスの基本機能を使うにあたってのヒント。 Gilson 600MPのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Gilson 600MPに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGilson 600MPのメーカー/サービスへの連絡先に関する情報。

Gilson 600MPについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGilson 600MPの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGilson 600MPで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)