Grizzly G8691の取扱説明書

21ページ 0.37 mb
ダウンロード

ページに移動 of 21

Summary
  • Grizzly G8691 - page 1

    WOOD LATHE WITH STAND MODEL G8691 INSTRUCTION MANUAL COPYRIGHT © 2000 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. FEBRUARY, 2001. PRINTED IN CHINA. ...

  • Grizzly G8691 - page 2

    -1- G8691 Wood Lathe w/ Stand Table Of Contents PAGE 1. SAFETY WARNINGS ............................................................................................................2 SAFETY RULES FOR ALL TOOLS ........................................................................3 ADDITIONAL SAFETY INSTRUCTIONS FOR G8691 .......................... ...

  • Grizzly G8691 - page 3

    -2- G8691 Wood Lathe w/ Stand Safety Instructions For Power Tools SECTION 1: SAFETY 5. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area. 6. MAKE WORK SHOP CHILD PROOF with padlocks, master switches, or by removing starter keys. 7. DON’T FORCE TOOL. It will do the job better and safer at the ...

  • Grizzly G8691 - page 4

    -3- G8691 Wood Lathe w/ Stand 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your e ...

  • Grizzly G8691 - page 5

    G8691 Wood Lathe w/ Stand Additional Safety Instructions For The Lathe 1. MAKE SURE ALL GUARDS are in place and that the lathe sits on a flat, stable sur- face. 2. ALWAYS WEAR EYE PROTECTION and a face shield when operating the lathe. Use a respirator to avoid inhaling dust. All safety equipment should be ANSI approved. 3. BEFORE STARTING THE MACHI ...

  • Grizzly G8691 - page 6

    -5- G8691 Wood Lathe w/ Stand 110V Operation SECTION 2: CIRCUIT REQUIREMENTS A 15-amp fuse or circuit breaker should be used when fusing this wood lathe. Circuit breakers rated any higher are not adequate to protect the circuit from power surges. Grounding This equipment must be grounded. Verify that any existing electrical outlet and circuit you i ...

  • Grizzly G8691 - page 7

    -6- G8691 Wood Lathe w/ Stand SECTION 3: INTRODUCTION We are proud to offer the Grizzly Model G8691 Wood Lathe w/ Stand. The Model G8691 is part of a growing Grizzly family of fine woodworking machinery. When used according to the guide- lines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly? ...

  • Grizzly G8691 - page 8

    -7- G8691 Wood Lathe w/ Stand Unpacking This wood lathe is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for deliv- ery, and the truck and driver are gone, you will need to file a freight claim with the carrier. Save the containers and all packing materials for possi- ble in ...

  • Grizzly G8691 - page 9

    -8- G8691 Wood Lathe w/ Stand Clean Up Grease left over from the manufacturing process may be on the various parts of the lathe. It is rec- ommended to clean this grease off with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. Avoid chlorine-based solvents as they may damage painted surfaces should they come in cont ...

  • Grizzly G8691 - page 10

    -9- G8691 Wood Lathe w/ Stand SECTION 4: ASSEMBLY Beginning Assembly Most of your Model G8691 Wood Lathe has been assembled at the factory, but some parts must be assembled or installed after delivery. We have organized the assembly process into steps. Please follow along in the order presented here. TOOLS REQUIRED: A metric socket set, 6" adj ...

  • Grizzly G8691 - page 11

    -10- G8691 Wood Lathe w/ Stand ASSEMBLY, CONT. Spur Center The Model G8691 is supplied with a #2 Morse Taper spur center for use when spindle turning. The spur center is used in conjunction with the tailstock live center. Before installing the spur center, thread spindle nut onto shaft and lightly tighten nut. Then insert the spur center into the h ...

  • Grizzly G8691 - page 12

    -11- G8691 Wood Lathe w/ Stand SECTION 5: OPERATIONS Once assembly is complete and adjustments are made to your satisfaction, you are ready to test run the machine. Turn on the power supply at the main panel. Press the START button. Make sure that your fin- ger is poised on the STOP button, just in case there’s a problem. The lathe should run smo ...

  • Grizzly G8691 - page 13

    -12- G8691 Wood Lathe w/ Stand OPERATIONS, CONT. Make sure the live center in the tailstock lines up with the spur center in the head- stock before turning anything between the centers. Failure to observe this step could result in the workpiece being thrown from the lathe. Serious personal injury could occur if care is not taken. Adjust the tool re ...

  • Grizzly G8691 - page 14

    -13- G8691 Wood Lathe w/ Stand SECTION 6: MAINTENANCE Lubrication V-Belt Since all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced. Do not lubricate them. Inspect regularly for tension and wear. Check pul- leys to ensure that they are properly aligned. Proper tension is indicated by no more t ...

  • Grizzly G8691 - page 15

    -14- G8691 Wood Lathe w/ Stand The following pages contain general machine data, parts diagrams/lists, troubleshooting guide and Warranty/Return information for your Model G8691 Wood Lathe. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department. Our trained servi ...

  • Grizzly G8691 - page 16

    -15- G8691 Wood Lathe w/ Stand Design Type ......................................................................................................Floor Model Overall Dimensions: Including Stand ........................................................................42" H x 17" W x 54 1 ⁄ 4 " L Shipping Weight ....................... ...

  • Grizzly G8691 - page 17

    -16- G8691 Wood Lathe w/ Stand ...

  • Grizzly G8691 - page 18

    -17- G8691 Wood Lathe w/ Stand Ref# Part# Description 001 P8691001 Motor 002 P8691002 Shaft Pin 003 P8691003 Motor Pulley 004 P8691004 Phillips® Hd Scr M6 x 20 005 P8691005 Belt Cover 006 P8691006 Motor Mount Plate 007 P8691007 Hex Head Screw M8 x 16 008 PW 01M Washer M8 009 P8691009 Hex Hd Scr M8 x 16 010 P8691010 Hex Hd Scr M6 x 12 011 P8691011 ...

  • Grizzly G8691 - page 19

    -18- G8691 Wood Lathe w/ Stand Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole writte ...

  • Grizzly G8691 - page 20

    -19- G8691 Wood Lathe w/ Stand 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ___Scroll Saw ___Disc/Belt Sander ___Spindle/Belt Sander __ ...

  • Grizzly G8691 - page 21

    FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_______________________________ Street_______________________________ City______________State______Zip______ Send a Grizzly Catalog to a friend: ...

メーカー Grizzly カテゴリー Lathe

Grizzly G8691のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- G8691の取扱説明書
- Grizzlyの製品カード
- パンフレット
- またはGrizzly G8691の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Grizzly G8691の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Grizzly G8691の取り付け説明書、サービスマニュアル、簡易説明書、またはGrizzly G8691のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Grizzly G8691の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Grizzly G8691デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGrizzly G8691を使用するのを助ける技術的文書のことです。説明書は通常、全てのGrizzly G8691ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Grizzlyの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Grizzly G8691の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGrizzly G8691の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Grizzly G8691に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Grizzly G8691デバイスの基本機能を使うにあたってのヒント。 Grizzly G8691のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Grizzly G8691に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGrizzly G8691のメーカー/サービスへの連絡先に関する情報。

Grizzly G8691についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGrizzly G8691の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGrizzly G8691で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)